The five-bolt connection shown must support an applied load of P = 330 kN. If the average shear stress in the bolts must be limited to 295 MPa, determine the minimum bolt diameter that may be used in the connection.

The five-bolt connection shown must support an applied load of P = 330 kN. If the average shear stress in the bolts must be limited to 295 MPa, determine the minimum bolt diameter that may be used in the connection.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.4.22P: , Solve the preceding problem using the numerical data: /) = 90mm, h = 280 mm, d = 210 mm, q = 14...

See similar textbooks

Related questions

Q: A hollow iron pipe with outside diameter of 240 mm is used as a column to carry a load of 80 kN.…

Q: A hollow steel tube with an inside diameter of 110 mm must carry a tensile load of 480 kN. Determine…

Q: The axial stresses are 12 MPa C in the wood post B and 150 MPa T in the steel bar A as shown below.…

A: Answer: (a) The load P is 70875 N. (b) The minimum diameter for pin C is 22.62 mm. (c) The minimum…

Q: The solid steel rod (1) has an allowable shear stress of 12 ksi. The brass tube (2) has an allowable…

Q: For the connection shown, the average shear stress in the 15-mm-diameter bolts must be limited to…

Q: Determine the required wire diameter

A: To determine the required diameter.

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 10 mm2.…

Q: For the connection shown, the average shear stress in the 16-mm-diameter bolts must be limited to…

Q: Two pieces of wood, 2 in. by 4 in., are glued together along the 40° Joint. Determine the maximum…

Q: The pipe assembly shown is subjected to a force F= 600 N. The pipe has an inner diameter of 20 mm…

A: Consider the Free Body Diagram: Torque,T=600*0.2 =120 N.mTorque acting on part BC,TBC=120 N.mTorque…

Q: The five-bolt connection shown must support an applied load of P = 370 kN. If the average shear…

A: Given data as per the question Applied load =370 KN Average shear stress =200Mpa

Q: The five-bolt connection shown must support an applied load of P = 214 kN. If the average shear…

A: Given:number of bolts, n=5Applied force, P=214 KNAverage shear stress, σ=249 MPa

Q: 1.55 In the structure shown, an 8-mm-diameter pin is used at A, and 12-mm-diameter pins are used at…

Q: A boiler with an outside diameter of 300 mm, length of 1000 mm and a wall thickness of 10 mm is…

A: According to the information we have a boiler with a diameter of 300 mm and a length of 1000 mm…

Q: The d = 13-mm-diameter solid rod passes through a D = 18-mm-diameter hole in the support plate. When…

A: To find: The maximum value of Pmax supported by structure. Given: The diameter of rod is d=13 mm1…

Q: 5.0 in. 3.0 in. The 1.4-kip load P is supported by two wooden members of uniform cross section that…

A: Given load P=1.4 kip Cross section A=5×3 in.2

Q: Q1: A hollow steel tube with an inside diameter of 80 mm must carry an axial tensile load of 330 kN.…

Q: The d = 12-mm-diameter solid rod passes through a D = 17-mm-diameter hole in the support plate. When…

Q: The normal stress in a piece of structural member is 300 MPa. If the modulus of rigidity G is 85…

A: Problem is based on strength of materials and can be solved as:

Q: The five-bolt connection must support an applied load of P = 3800 lb. If the average shear stress in…

Q: For the connection shown, the bolt diameter is d = 30 mm. The average shear stress in the bolts…

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A: Given: Let us consider the given data, d=0.75P=56 kipsn=5 Where, d=Diameter P=Applied load n=Bolt…

Q: For the connection shown, the bolt diameter is d = 20 mm. The average shear stress in the bolts must…

Q: Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

Q: The five-bolt connection shown must support an applied load of P-500 kN. If the average shear stress…

Q: Assuming that the load P = 120 KN is carried equally by the four rivets in the figure showing the…

A: Solution: a) Shear force in each rivet=P4=1204=30kN Since the rivets are in double shear, the shear…

Q: The bar AB is supported by a frictionless inclined surface at A and a % in diameter pin at B that is…

Q: Torsion. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which…

A: Given data: ◆ The bolt circle diameter: D = 250 mm ◆ The number of bolts: n = 12 bolts ◆ The…

Q: For the connection shown, the average shear stress in the 6-mm-diameter bolts must be limited to 176…

Q: 2] The I-beam column shown below is to support a normal load of value P. The column has a cross-…

Q: determine the minimum bolt diameter that may be used for this connection.

Q: 2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the…

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A: Given: P=64 kips d=0.75 in

Q: For the clevis connection shown, the shear stress in the 5/16-in.-diameter bolt must be limited to…

A: Given data: d=516 inτ=32 ksi Need to determine the maximum allowable load that can apply.

Q: Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

Q: Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 15…

A: Given, d = 15 mmτmax = 120 MPa = 120 N/mm2θmax = 5° = 0.08727 radG = 80 GPa = 80,000 N/mm2l = 500 mm…

Q: QUESTION 1. Determine the constant thickness t of the square shaped tube if the average shear stress…

A: Given data: The average shear stress is; ? = 90 MPa. The magnitude of the torque is; T = 3 kNm. The…

Q: Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution…

Q: Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

A: To find : determine the largest allowable value of P. Given :- diameter of shaft ds=30 mm shear…

Q: 5. The cast iron block with cross-sectional dimensions of 2.5 inches by 2.5 inches consists of two…

Q: The rivet group connects two narrow lengths of plate, one of which carries a 15 kN load. If the…

A: Formula And Concept Of Rivet Joint Used

Q: The bracket shown below is to carry a load F = 20 kN acting at an eccentricity of 1.2 from the…

A: givenbracket carry a load F = 20 kNeccentricity e=1.2 mshear stress in the rivets is not to exceed…

Q: The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable…

A: given; diameter of steel(d1)=0.500inallowable shear stress of steel(τs)=13ksimaximum torque…

Q: (a) the normal stresses in the steel plates (1) and the oak block (2). (b) the shortening of the…

Q: Problem #5: If the allowable normal stress for the bar is 120 MPa, determine the maximum axial force…

Q: For a lap joint, determine the maximum safe load P which may be applied if the shearing stress in…

Q: The average shear stress in each of the 6mm-diameter bolts cannot exceed 80 MPa. Furthermore, the…

Question

100%

The five-bolt connection shown must support an applied load of P = 330 kN. If the average shear stress in the bolts must be limited
to 295 MPa, determine the minimum bolt diameter that may be used in the connection.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The five-bolt connection must support an applied load of P = 1800 lb. If the average shear stress in the bolts must be limited to 47 ksi, determine the minimum bolt diameter that may be used for this connection.
For the connection shown, the average shear stress in the 15-mm-diameter bolts must be limited to 179 MPa. Determine the maximum load P that may be applied to the connection.
The rivet group connects two narrow lengths of plate, one of which carries a 15 kN load. If the ultimate shear strength t of a rivet is 350 N/mm² and its failure strength in compression stress is 600 N/mm², determine the minimum allowable values of rivet diameter d (mm) and plate thickness t (mm).
Assuming that the load P = 120 KN is carried equally by the four rivets in the figure showing the double lap connection, determine the following: (a) the shear stress in the rivets if the diameter of the rivet is 16 mm and (b) the thickness of the inner steel plate if the bearing stress is132.63 MPa.
The horizontal bar shown is pinned at O and is supported with a helical springat L1 from O. L1=2m, L2=1m. The spring has 30 turns and the diameter of the wire usedis 20mm. The diameter of the spring is 125mm. Modulus of Rigidity = 83GPa. Determine the shear stress of the helical spring loaded as shown if w = 25kN/m.
A solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the limiting stress of the bar is 27.24 kPa determine the cross sectional area of the steel square bar and its dimensions.
A steel wire 5 m long hanging vertically supports a weight of 1200 kN. Determine the required wire diameter if the stress is limited to 140 MPa and the total elongation must not exceed 4 mm. Neglect the width of the wire and assume E=200 GPa.
A stainless steel tube with an outside diameter of 50 mm and a wall thickness of 5 mm is used as a compression member. If the axial stress in the member must be limited to 384 MPa, determine the maximum load P that the member can support.
A piping tube with an outside diameter of 50 mm and wall thickness of 5 mm is used as a compression member. Determine the maximum load P that the member can support if the normal stress in the member must be limited to 120 MPa.
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 17 mm. Determine the allowable value of P if the shear stress in the shaft is not to exceed 134 MPa. Use G = 80 GPa for steel.
A steel wire 5-m long hanging vertically supports a weight of 1200 N. Determine the required wire diameter if the stress is limited to 140 MPa and the total elongation must not exceed 4 mm. Neglect the weight of the wire and assume E = 200 GPa.
2. A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN. Determinethe outside diameter of the tube if the stress is limited to 120 MN/m2.