Q1: On the shaft H.P. Turbine of open cycle gas power plant drives the L.P. compressor,for the other side L.P.Turbine drives the H.P. Compressor and the generator. The reservoirof plant has 1.1bar, 26 °C. Max. cycle temperature 722 °C, the pressure ratio of eachcompression stage 2.6, turbine compressor efficiencies is 0.82, regenerator effectiveness77%, the pressure drop for each side of generator and heater is Y%.1- Find an expression for the output temperature of first turbine by the units of input planttemperature.2- Sketch the T-s diagram and calculate the air rate, power output for turbines andcompressors with cycle thermal efficiency assuming intercooling to ambient temperatureand reheating to max. cycle temperature. Calorific value of fuel is X MJ/kg, combustionefficiency is 97%.3- Obtain SSC , When specific heat at constant pressure for air and gases is 1.005, 1.14kJ/kg.K respectively.Yg = 1.33, output power of the plant = 1880KWX and Y values are mentioned at the second page.X33Y=2.65

01: On the shaft H.P. Turbine of open cycle gas power plant drives the L.P. compressor, or the other side L.P.Turbine drives the H.P. Compressor and the generator. The reservoir of plant has 1.1bar, 26 °C. Max. cycle temperature 722 °C, the pressure ratio of each ompression stage 2.6, turbine compressor efficiencies is 0.82, regenerator effectiveness "7%, the pressure drop for each side of generator and heater is Y%. - Find an expression for the output temperature of first turbine by the units of input plant emperature. - Sketch the T-s diagram and calculate the air rate, power output for turbines and ompressors with cycle thermal efficiency assuming intercooling to ambient temperature nd reheating to max. cycle temperature. Calorific value of fuel is X MJ/kg, combustion fficiency is 97%. - Obtain SSC , When specific heat at constant pressure for air and gases is 1.005, 1.14 J/kg.K respectively. 9 = 1.33, output power of the plant = 1880kW K and Y values are mentioned at the second page. X33 Y=2.65

01: On the shaft H.P. Turbine of open cycle gas power plant drives the L.P. compressor, or the other side L.P.Turbine drives the H.P. Compressor and the generator. The reservoir of plant has 1.1bar, 26 °C. Max. cycle temperature 722 °C, the pressure ratio of each ompression stage 2.6, turbine compressor efficiencies is 0.82, regenerator effectiveness "7%, the pressure drop for each side of generator and heater is Y%. - Find an expression for the output temperature of first turbine by the units of input plant emperature. - Sketch the T-s diagram and calculate the air rate, power output for turbines and ompressors with cycle thermal efficiency assuming intercooling to ambient temperature nd reheating to max. cycle temperature. Calorific value of fuel is X MJ/kg, combustion fficiency is 97%. - Obtain SSC , When specific heat at constant pressure for air and gases is 1.005, 1.14 J/kg.K respectively. 9 = 1.33, output power of the plant = 1880kW K and Y values are mentioned at the second page. X33 Y=2.65

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A power plant operates between pressures of 80 bar and 0.1 bar in an actual Rankine cycle. The maximum cycle temperature is 650 deg. Celsius. for mass flow rate of 5 kg/sec. Condensate pump has an isentropic efficiency 82% and Turbine isentropic efficiency of 93%. Determine: a. Actual Turbine Work (KW) b. Actual Work Net (KW) c. Decrease in efficiency due to irreversibility
A rankine turbo generator unit receives 27000kg/h of steam at 1.2mpa and superheat by 122 degree. Condensate leaves at 22°c. For a brake steam rate of 4.74 kg/kwh, mechanical efficiency of 94%, determine (a) the ideal cycle thermal efficiency, (b) the indicated engine efficiency, (c) the condition of turbine actual exhaust, and (d) the turbo generator output in kw.
In a gas turbine plant working on air standard Brayton cycle, the air at inlet is at 27°C temperature ,0.1 MPa pressure respectively.The pressure is 6.25 and maximum temperature is 800° C the turbine and compressor efficiencies are each 80%. Find per kg of air; i) The compressor work ii)The turbine work iii) The cycle efficiency iv) The turbine exhaust temperature
Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 300 K, with a volumetric flow rateof 5 m3/s. The compressor pressure ratio is 10. The turbine inlet temperature is 1400 K. The thermal efficiency is 45.7%, back work ratio is 39.6%, net power delivered is 2481 kW. Determine the rate of heat transfer to the air passing through the combustor, in kW.
Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 27 °C, with a volumetric flow rate of 5 m3/s. The compressor pressure ratio is 5. The turbine inlet temperature is 1127 °C. Assume cold-air analysis, determine the back work ratio.
A regenerative gas turbine with intercooling and reheat operates at steady state. Air enters the compressor at 100 kPa, 300 K with a mass flow rate of 5.807 kg/s. The pressure ratio across the two-stage compressor is 10. The pressure ratio across the two-stage turbine is also 10. The intercooler and reheater each operate at 300 kPa. At the inlets to the turbine stages, the temperature is 1400 K. The temperature at the inlet to the second compressor stage is 300 K. The regenerator effectiveness is 80%. Determinethe thermal efficiency.
show complete and step by step solution with ts diagram illustration. REGENERATIVE CYCLE AN ENGINE
Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 300 K, with a volumetric flow rateof 5 m3/s. The compressor pressure ratio is 10. The turbine inlet temperature is 1400 K. Determine the rate of heat transfer to the air passing through the combustor, in kW.
an ideal reheat turbine with one stage of reheat receieves steam at 8 mpa, 480 degrees celsius. reheat pressureis 0.83 mpa and exhaust pressure is 0.0007 mpa. determine A) heat added B) effeciency cycle C) energy chargable D) engine thermal effeciency
Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 27 °C, with a volumetric flow rate of 5 m3/s. The compressor pressure ratio is 5. The turbine inlet temperature is 1127 °C. Assume cold-air analysis, determine the net power developed of the cycle.
Air enters the compressor of an ideal air standard Brayton cycle at 100 kPa, 290 K, with a mass flow rate of 6 kg/s. The compressor pressure ratio is 10. The turbine inlet temperature is 1500 K. If a regenerator with an effectiveness of 70% is incorporated in the cycle, determine (i)turbine work, (ii) compressor work, (iii) heat supplied, and (iv) the efficiency of the cycle. Draw a suitable block diagram and T-s diagram. Take Cp=1.005 kJ/kg K and ϒ= 1.4
Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 27 °C, with a volumetric flow rate of 5 m3/s. The compressor pressure ratio is 5. The turbine inlet temperature is 1127 °C. Assume cold-air analysis, determine the net power developed of the cycle. determine the thermal efficiency of the cycle. Determine the heat rejected to the condenser, in kW, determine the back work ratio. determine the input heat into combustor, in kW.