For a Rankine cycle, higher steam pressures and temperature conditions can be achieved because of the development of new exotic materials. With the condenser pressure found in problem 2, the following conditions exist: Tmax=600 deg C Pmax=20 MPa TRH=620 deg C (maximum possible temperature that can be used) The pump efficiency is 75% and the turbine efficiency if 87% What should be used for a reheat temperature? 620 deg C 500 deg C 550 deg C 285 deg C

For a Rankine cycle, higher steam pressures and temperature conditions can be achieved because of the development of new exotic materials. With the condenser pressure found in problem 2, the following conditions exist: Tmax=600 deg C Pmax=20 MPa TRH=620 deg C (maximum possible temperature that can be used) The pump efficiency is 75% and the turbine efficiency if 87% What should be used for a reheat temperature? 620 deg C 500 deg C 550 deg C 285 deg C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The Steam Engine for a simple Rankine Cycle with super heat vapor steam power plant, drives 150 kW generator of 90% electrical efficiency. Steam rate, 6.7 kg per bhp-hr; steam pressure, 1,034.6 kPag, 55.6°C superheat; exhaust to condenser at 15.2 cm Hg abs. No feedwater heating. Motor driven boiler feed-pump. Other data are as follows: Enthalpy of steam at 1,034.6 kPag & 55.6°C sh = 2,919 kJ/kg; Enthalpy of steam at 15.2 cm Hg abs. (after isentropic expansion work) = 2,252 kJ/kg; Enthalpy of Condensate at 15.2 cm Hg abs (hf) = 252.8 kJ/kg; and Specific Volume of Condensate = 0.001019 m3/kg.Determine the unitary Feedwater pump work, in kJ/kg. Determine the Ranking Cycle Efficiency in %.Determine the Brake Thermal Efficiency of the cycle in %. Determine the Combined thermal and electrical efficiency in %.
An ideal Rankine cycle operates between a steam boiler pressure of 18 MPa and a condenser temperature of 42 °C. The steam leaving the boiler is a saturated vapor. The net power generated by the cycle is 150 MW. What is the mass flow rate of steam? What is the cycle efficiency? Use the formula: n=Wnet/Qin.
In a Rankine cycle steam enters the turbine at 2.5 MPa (enthalpies & entropies given) and condenser of 50 kPa (properties given), what is the thermal efficiency of the cycle? At 2.5 MPa: hg = 2803.1 kJ/kg; sg = 6.2575 At 50 kPa: sf = 1.0910; sfg = 6.5029; hf = 340.49; hfg = 2305.4; vf = 0.0010300
Solve the Rankine Cycle problems. Draw a detailed Schematic and Ts Diagram. Show a clear and detailed solutions. 1, Consider a steam power plant that operates on an ideal reheat Rankine Cycle.The Plant maintains the boiler at 8MPa, the reheat section at 700kPa.and the condenser at 10kPa. The mixture quality at the exit of both turbines is 93%. Determine the temperature at the inlet of each turbine .
in a rankine cycle, what is the entrance pressure of the turbine if the condenser pressure is 105 kpa and the pump work is 20 kj/kg. use density of water entering the pump, 950 kg/m^3.
Consider below ideal reheat Rankine Cycle (operating with water):a) Draw T-s diagramb) Mass flow ratec) Thermal efficiencyd) Thermal power supplied to the burnere) Carnot efficiencyf) Second law efficiency of this cycle xx=40 , yy=20
Q2/ Actual Rankine cycle, has the following specifications: Boiler pressure is 160 bar and Turbine inlet temperature is 600 Co and Condenser pressure is 0.08 bar , Turbine efficiency is 0.9 and Pump efficiency is 0.85 and Steam mass flow rate is 130 kg/s Calculate: 1-Work net (kW). 2-heat addition (kW) 3-thermal efficiency.
1. A reheat steam cycle has 13,580 kPa of throttle pressure at the turbine inlet and a 37.50308414 atm reheat pressure, the throttle and reheat temperature of the steam is 1302 R, condenser pressure is 4.3 kPa. Determine the difference between the simple Rankine cycle efficiency and the reheat Rankine cycle efficiency, in percent.
A simple Rankine cycle uses water as a working fluid. The boiler operates at 6000 kPa and the condenser at 50 kPa. At the entrance to the turbine, the temperature is 450 degrees celcius. The isentropic efficiency to the turbine is 90%, pressure and pump losses are negligible, and the water leaving the condenser is subcooled to 6.32 degrees celcius. The boiler is sized for the mass flow rate of 20 kg/s. Determine: a) The rate at which heat is added in the boiler b) The power required to operate the pumps c) The net power produced by and thermal efficiency of the cycle
In an ideal Rankine cycle, steam generated at 3.546 Mpa and 450°C. The condenser isat 45°C. Determine (a) the ideal pump work, (b) the cycle efficiency, (c) for an enginewith the same end state, determine the engine efficiency.(Note: Draw the schematic and T-s diagram)
Superheated steam generated in a power plant at a pressure of 8,600 kPa anda temperature of 500 ℃ is fed to a turbine. Exhaust from the turbine enters acondenser at 15 kPa, where it is condensed to saturated liquid, which is thenpumped to the boiler.(a) What is the thermal efficiency of a Rankine cycle operating at theseconditions?(b) What is the thermal efficiency of a practical cycle operating at theseconditions if the turbine efficiency and pump efficiency are both 75%?Which of the two efficiencies has greater impact on the thermal efficiency?(c) Sketch both cycles in the same T-s diagram.(d)If the power output of the turbine is 80,000 kW in case (b), calculate themass flow rate of the working fluid.(e) Calculate the heat transfer rates in the boiler and the condenser. Doublecheck the result for the condenser.(f) For both cases (a) and (b), make a comment about the operation of turbine(issue of cavitation). [one sentence is fine](g) How you would operate the condenser of a practical…
1. In a Rankine cycle, steam enters the turbine at 2.5 MPa and condenser at 50 kPa, what is the thermal efficiency of the cycle?At 2.5 MPa: hg = 2803.1 kJ/kg sg = 6.2575 kJ/ kg – KAt 50 kPa: sf = 1.0910 sfg = 6.5029hf = 340.49 hfg = 2305.4vf = 0.0010300