Please solve the question in 20 minutes. 02-In the below circuit the zener diode acts as voltage regulator. Given that V,= 12V and thezener diode has the following specification z= 52,V=7V@10 mA, Ik=0.1mA andIzin 100 mA andThe min output voltage .-6.15b) The maximumi allowed resistance ,1002) The minimuni allowed load resistance =The load regulation ,%

Brief description : Here they have mentioned a zener voltage regulator circuit which is used to…

02-In the below circuit the zener diode acts as voltage regulator. Given that V,=12V and the zener diode has the following specification Izin= 100 mA and = 52,V=7V@10 mA, Ik=0.1mA and The min output voltage =.61.15 b) The maximum allowed resistance =, 1002 The minimum allowed load resistance = R_ The load regulation7C,%

02-In the below circuit the zener diode acts as voltage regulator. Given that V,=12V and the zener diode has the following specification Izin= 100 mA and = 52,V=7V@10 mA, Ik=0.1mA and The min output voltage =.61.15 b) The maximum allowed resistance =, 1002 The minimum allowed load resistance = R_ The load regulation7C,%

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
Q1: In this Zener diode regulator, the source voltage varies from 6 V to 14 V. Assume that the load current varies between 1 mA and 35 mA, and that the diode is an ideal 4 V Zener diode. What is the largest allowable resistance that will ensure the load voltage remains constant with variations in load current and source voltage? Please enter your answer to 3 significant figures. Q2: Given the circuit design for a Zener diode regulator in the Ques 1, what is the maximum power that will be dissipated by the Rs resistor? You are told that the source voltage Vs varies from 6 V to 11 V, the load current il varies between 2 mA and 45 mA, and the diode is an ideal 3 V Zener diode. You will need to recalculate the maximum allowable resistance Rs with your new values, as part of this question. Please enter your answer to 3 significant figures, and in Watts.
We have a junction diode that has iD = 0.2 mA for vD = 0.6 V. Assume that n = 2 and VT = 0.026 V. Use the Shockley equation to compute the diode current at vD = 0.65 V and at vD = 0.70 V.
6) We can say about the zener diode:a) The Zener diode works in the breakdown region, that is, it works with reverse bias.b) The Zener diode must be connected in series with a current limiting resistor for the Zener, Rs.c) The use of the Zener diode and its current limiting resistor must be placed in parallel with the load.d) The Zener diode and its current limiting resistor should not be considered as a type of voltage regulator.e) None of the above statements are correct.
For the diode applied in the circuit has a knee current of 5mA, and a maximum allowed power dissipation of 300mW. What are the maximum and minimum load currents that can be drawn safely from the circuit with constant voltage output Vo of 6V?
A silicon diode is in connected to a DC voltage source with Forward biased, the net currentflowing through the diode is (25mA) where the applied voltage across the terminals of thediode is (820mV). Determine diode temperature, if Is "dark saturation current", the diodeleakage current density in the absence of light is 3.4 × 10−10 A
Considering a clamper circuit, where capacitance C, load R, the cut-in voltage of diode are unknown, which is the correct statement 1- the dc level of the signal changes 2- the peak-to-peak value of signal changes 3- the shape of signal changes 4- the dc level shifts up 5- the dc level shifts down
Given the clamper circuit below, assume that the value of R and C are large enough sothe voltage across the capacitor does not change significantly during the interval of time.a. Using the simplified diode model, simulate the action of the circuit when the Silicon diode isin forward and reverse bias condition and measure the corresponding output voltage.b. Draw the complete output waveform of the circuit
The diode current in a p-n junction is modeled exponentially (given below.) When the p-n junction is polarized with 0.7V and 0.75V, the currents flowing through the diode are again measured on the basis of 1.36 mA and 7.20 mA. Accordingly, what is the ideality factor? (Note: Take the thermal voltage as mV)
Zener voltage, VZ = 6.1V and incremental resistance, rz = 0 a) Determine the value of Ri such that the Zener diode remains in breakdown if the load current varies from IL = 20 to 200 mA and if the input voltage varies from VI = 8.6 to 10V. Assume IZ(min) = 0.1IZ(max). b) Determine the power rating required for the Zener diode and the load resistor. c) If the position of Zener diode were changed to be in forward bias region, will the voltage regulator still work properly? Justify your answer
Design a voltage-regulator circuit to provide a constant voltage of 5 V to a load from a variable supply voltage. The load current varies from 0 to 100 mA, and the source voltage varies from 8 to 10 V. You may assume that ideal Zener diodes are available. Resistors of any value may be specified. Draw the circuit diagram of your regulator, and specify the value of each component. Also, find the worst case (maximum) power dissipated in each component in your regulator. Try to use good judgment in your design. Repeat Problem P9.29 if the supply voltage ranges from 6 to 10 V.