Q4 Example 3.5A U-tube manometer similar to that shown in Figure 3.8 is used to measure the gaugepressure of a fluid P of density p= 1000 kg/m. If the density of the liquid Q is 13.6 x10° kg/m, what will be the gauge pressure at A if h; = 0.15 m and h2 = 0.25 m aboveBC. Take into consideration patm = 101.3 kN/m.Fluid PFigure 3.8Solution to Example 3.5Putting,PQ = 13.6 x103Pp = 1000 kg/mhi = 0.15 mh2 0.25 m

Answered: Image /qna-images/answer/d52e010b-cfac-4842-8cb4-671bd67adaaa.jpg

Answered: 04 Example 3.5 A U-tube manometer…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A U-tube differential manometer is connected to two pipes at A and B. Pipe A Contains oil of density 1400 Kg/m3 and pipe B is carrying fluid of density 850 Kg/m3. If the pressure at point A is 195 kN/m2. Find the pressure at point B for the following data h1=11 cm, h2=7.5 cm and h3=23.5 cm. The specific gravity of mercury is13.6?
Three types of fluids stack in an open tank as shown in the picture. If the specific gravidties are sg1=1.00, sg2=2.00, sg3=3.00, and h1=1.00 m, h2=1.00 m, h3=1.00 m, calculate the gage pressure at location 4, P4(gage)=_________(kPa)
6.At sea level a mercury barometer reads 750 mm and at thesame time on the top of the mountain another mercury barometer reads 745 mm. If the specific weight is uniform at 12 N/m3, determine the height of the mountain. Fluid Mechanics
An open manometer, shown in the figure, is installed to measure the pressure in a pipe carrying an oil (SG = 0.82). If the manometer liquid is carbon tetrachloride (SG = 1.60) determine the pressure in the pipe (in N/m2). Find the pressure head in meters of water column height.
Shown in figure below, the manometer fluid of density 875 kg/m3 shows a column height difference of 3 cm with one end attached to a pipe and the other open to atmosphere at 101 kPa. What is the absolute pressure in the pipe in psi?
An open tank contains water up to a depth of 1.2m from the bottom and above it mercury for a depth of 0.8m and above it an oil of specific gravity 0.8 for a depth of 1m. Assume the atmospheric pressure is 1 bar. Find the gauge pressure and absolute pressure i) at the bottom of the container, ii) at the interface of water and mercury and iii) at the interface of an oil and mercury. ( i) At bottom Gauge Pressure = ________________N/m2 Absolute Pressure =_________________ N/m2 ii) At the interface of water and mercury Gauge Pressure =_______________ N/m2 Absolute pressure =_____________ N/m2 iii) At the interface of oil and mercury Gauge Pressure =_____________ N/m2 Absolute Pressure = _________________ N/m2
The gage pressure of air in a pressurized water tank is measured simultaneously by both a pressuregage and a manometer. The differential height h of the mercury column is to be determined. Assumptions The air pressure in the tank is uniform (i.e., its variation with elevation is negligible dueto its low density), and thus the pressure at the air-water interface is the same as the indicated gagepressure.
The pipe (0-1-2) shown in the …gure is angled upward at 30 and is …lled with water. The distance from (1) to (2) (along the pipe) is 1.2 m. The manometer liquid is mercury. For part (a), the pipe is capped at location (0) so that the water is stationary in the pipe. What would be the value of h in this case? For part (b), the pipe shown is just a section of a much longer pipe, and water is ‡owing upwards from (0) to (1) to (2). If the pressure loss due to friction from location (1) to location(2) is 20 kPa, what is the value of h in this case?
A pressure gauge on a receiver tank reads 125.5 psi at sea level. If this tank were brought to Huancayo Peru at an altitude of 10,013 ft with an air pressure of 10.2 psi, what would the tank pressure read?
In the figure, pressure gauge A shows 1.5 kPa (gauge). Fluids are at 20 ° C. Determine the elevation z in meters of the level at which to find the liquids in tubes B and C.
Water fl ows upward in a pipe slanted at 30 ° , as in Fig. .The mercury manometer reads h =12 cm. Both fl uidsare at 20° C. What is the pressure difference p 1 - p 2 inthe pipe?
(Just Question a.) A water filled pipe has water flowing at v1= 5.90 m/s in a section of pipe where the diameter is d1= 20.2 cm and the pressure is known to be P1= 7.00×104 N/m2 above atmospheric pressure. If the pipe carries the water 3.5 meters up hill without any change in diameter, what is the new absolute pressure within the pipe? After flowing up the hill described above, the pipe narrows to 80% of its original radius, what will be the new water velocity (v2) in the pipe? What will be the absolute pressure (P3) in the smaller pipe? a. What is the volume flow rate through the smaller pipe?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS