Part 1: Rotating Viscometer One type of viscometer involves the use of a rotating cylinder inside a fixed cylinder as shown in the figure below. The gap between the cylinders must be very small to achieve a linear velocity distribution in the liquid. Design a viscometer that will be used to measure the viscosity of motor SAE 30 oil| from 0°C to 100°C. Here you need to determine and report the following parameters: a. The dimensions of the two cylinders, lengths, thicknesses and diameters. b. The gap clearance between the surfaces of the cylinders. c. The rated power of the driving motor. d. The rotational speed of the shaft. e. Assumptions, and operational procedure. Rotating Drum Viscometer Drive Motor Rotating Cylinder Viscos Liquid Sample Stationary Cylinder Figure 3: Schematic for task 3 part 1.

Part 1: Rotating Viscometer One type of viscometer involves the use of a rotating cylinder inside a fixed cylinder as shown in the figure below. The gap between the cylinders must be very small to achieve a linear velocity distribution in the liquid. Design a viscometer that will be used to measure the viscosity of motor SAE 30 oil| from 0°C to 100°C. Here you need to determine and report the following parameters: a. The dimensions of the two cylinders, lengths, thicknesses and diameters. b. The gap clearance between the surfaces of the cylinders. c. The rated power of the driving motor. d. The rotational speed of the shaft. e. Assumptions, and operational procedure. Rotating Drum Viscometer Drive Motor Rotating Cylinder Viscos Liquid Sample Stationary Cylinder Figure 3: Schematic for task 3 part 1.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A concentric cylinder viscometer may be formed by rotating the inner member of a pair of closely fitting cylinders. The annular gap is small so that a linear velocity profile will exist in the liquid sample. Consider a viscometer with an inner cylinder diameter of 4 in, a height of 8 in, and a clearance gap width of 0.001 in, filled with castor oil at 90 oF. Determine the torque (in lbf×ft) require to turn the inner cylinder at 400 rpm. The dynamic viscosity of the caster oil is 0.0079 lbf×s /ft2.
Find the dynamic and kinematic viscosities of water at 327 K.
One type of viscometer involves the use of a rotating cylinder inside a fixed cylinder as shown in the figure below. The gap between the cylinders must be very small to achieve a linear velocity distribution in the liquid. Design a viscometer that will be used to measure the viscosity of motor SAE 30 oil from 0°C to 100°C. d. The rotational speed of the shaft.
What methods exist to calculate the viscosity of dense gases and liquids?
A tape, of width w = 25.40 mm is to be coated on both sides with a lubricant by drawing in throughnarrow gap of length, L as depicted in Figure 2. Following below values are given:c = 0.300 mm, t = 0.381 mm, and L = 20.0 mm.The lubricant, of dynamic viscosity  = 1.0054 kg/m.s completelys fills the gap and the velocitydistribution is asssumed to linear as shown in Figure 2. The maximum allowable force in tape isgiven as F = 30.04 N. Find the maximum allowable tape speed
what is the relationship between the fluid viscosity and the drag force Fdrag?
A Pipe used to transport an oil of specific gravity of 0.90 & 0.03poise at a Velocity of 1.6977m/s with a flow rate of 3cubic meter per second. A Pipe was used to conduct a test using water at 20 degree celsius with a velocity of 5.0931m/s. Find the diameter of the prototype. Viscosity of water at 20 degree celsius is 0.01poise
Find the dynamic and kinematic viscosities of kerosene, SAE 10W-30 motor oil, and water at a temperature of 38°C (100°F). show solution.
An oil film of thickness 1.5 mm is used for lubrication between asquare plate of size 0.9 m × 0.9 m and an inclined plane having anangle of inclination 200. The weight of the square plate is 392.4 N andit slides down the plane with a uniform velocity of 0.2 m/s. Find thedynamic viscosity of the oil
In a falling-ball viscometer, a steel ball 1.6 mm in diameter is allowed to fall freely in a heavy fuel oil having a specific gravity of 0.95. Steel weighs 79 kN/m3. If the ball is observed to fall 250 mm in 10.5 s, calculate the viscosity of the oil.
A rotating viscometer consists of two concentric cylinders—a stationary inner cyliner of radius Ri and an outer cylinder of inside radius Ro rotating at angular velocity (rotation rate) ?o. In the tiny gap between the two cylinders is the fluid whose viscosity (? ) is to be measured. The length of the cylinders in Fig is L. L is large such that end effects are negligible (we can treat this as a two-dimensional problem). Torque (T) is required to rotate the inner cylinder at constant speed. Showing all your work and algebra, generate an approximate expression of T as a function of the other variables.
SAE 10W30 motor oil has a dynamic viscosity of 0.21 kilograms per meter second and a specific gravity of 0.896 (a) What is the density of the motor oil in units of kilograms per cubic meter?