05. Determine the forces in members DE, DI, and JI of the arched roof truss shown below. ¢4>6 6*4> 4 6 6→4> | 100 kN 75 kN 75 kN D 25 kN- E 25 kN 3 МЕMBER FORCE (kN) DE F B DI JI K H 14 G Dimensions in meters

05. Determine the forces in members DE, DI, and JI of the arched roof truss shown below. ¢4>6 6*4> 4 6 6→4> | 100 kN 75 kN 75 kN D 25 kN- E 25 kN 3 МЕMBER FORCE (kN) DE F B DI JI K H 14 G Dimensions in meters

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.76P: The 50-ft measuring tape weighs 2.4 lb. Compute the span L of the tape to four significant figures.

See similar textbooks

Related questions

Q: The member is supported by a pin at A and cable BC. Determine the components of reaction at these…

Q: Figure 6 m 4 m B Part A Determine the force in member DE of the truss, and state if the member is…

A: Given that: For the truss, F1 = 550 N, F2 = 870 N It is required to determine: (a) Force in member…

Q: The forces in the member BC and BD respectively are B 2m D 2m 2m 2m 10KN 2m 20 A V3 (Tensile) and v3…

A: Data given-

Q: h 0.75 m 0.4 m B Fig. Q5. Q5. A plane truss subjected to loading as shown in Fig. Q5. If P = (1500 +…

Q: Use method of sections only. Detailed Steps

A: The above truss with support reactions is given as, Now, apply force equilibrium in the horizontal…

Q: A vat holding paint (s.g. =0.80) is 14 m long (L) and 3 m deep (D) and has a trapezoidal cross…

A: Given :-Specific gravity of paint (S.G)=0.80L=14 mD=3 mA= 4 mB=15 mTo find:- force on the bottom of…

Q: P G H P2 a E В a/2 a/2 As shown, a truss is loaded by the forces P = 497 lb and P = 192 lb and has…

Q: In the figure shown, the blocks weigh 200 N each. Both are connected by a horizontal bar weighing…

Q: 10 N 80 N Ra (400, 200 200, 300 20 N 50 N (200, 500) $400, S00) R, R1 3. A table 600 mm by 600 mm is…

A: Draw a diagram for the problem showing the reactions on each leg. Here, R1, R2, and R3 are the…

Q: Q7: The structure consists of a collar at B that is free to slide along a straight fixed bar AC.…

A: Draw the free body diagram for given system,Apply the condition of equilibrium,R=T cos 30 + T cos 60…

Q: Problem 5 From the given truss shown: 100 N 200 N D A В 150 N 1.5 m 3 m 1.5 m Question 13 Which of…

Q: Frames are commonly used to support various external loads. 0.4 m -1.6 m- 0.4 m F How is a frame…

A: Given:- To Determine :- Reactions at support

Q: A load weighing P kN as with AB, AC and AD cables such as are carried. Points A and B are x-axis, C…

Q: Calculate the magnitude of the force (in kN) on bar AB. Take P = 30.0 kN, do not put units in the…

A: .

Q: Determine the force in each member of the truss (positive value for tension and negative for…

Q: For the system shown in Fig. 1, determine the generalized physical properties m", c", k", and the…

A: We have to calculate the m,k,c explaining with physical properties and Dimensions

Q: Two weights are connectedby a very light, flexible cord that passesover an 80.0 N frictionless…

A: Given data: Radius of pulley (R) = 0.3 m Weight of block (W1) = 75 N Weight of block (W2) =125 N…

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

Q: Compute the forces in each member of the Warren Truss.' 2000 N 3000 N D 60 60 60 60 E A 10 m 10 m…

Q: 50 in. B 6.C1 For the loading shown, determine the force in each member of the truss as a function…

Q: A39 A uniform rod AB of weight W and which is 20 cm long is suspended by two vertical springs X and…

Q: Spring Dimension: Spring 1 Spring 2 Steel Bronze Rigid bar of (1) negligible mass Dm= = 100 mm Dm =…

Q: A block (A) weighing 1 kN rests on a rough inclined plane whose inclina- tion to the horizontal is…

A: Draw the FBD for the given question and write the given values along with suitable variables.

Q: Application of Equilibrium Solve for the value of unknown variables Given : P1 = 6.85 KN P2 =…

A: Draw the free-body diagram of the beam. As there is no horizontal force acting on the beam so the…

Q: he simplest truss consists of two rods and is loaded by the block. Given: block weight Q = 9,4 kN.…

A: assuming full rigidity we will use lammi's theorem to solve this problem

Q: For the system shown, if taking the frame as free body, how many forces should you consider in the…

A: Construction Of FBD

Q: 500 N 3 4 W = 200 N Ms = 0.3 Mk = 0.2

Q: calculate the forces in the ribs of the Muslim shown in Figure (1) and are the ribs of the Muslim in…

Q: Q : An 1800-N load P is applied to the pulley C, which can roll on the cable ACB. The pulley is held…

Q: QUESTION 7 While sitting in a chair, a person exerts the forces in the diagram of Figure 7.…

Q: A cable is loaded and supported as shown in Fig. The vertical distance vc is 4 ft. Determine The…

A: Let Ax and Ay be the normal reaction at support ADx and Dy be the normal reaction at support…

Q: 1.6.10If the component of force P parallel to the incline is 400 N, determine the value of P and its…

Q: A mechanism carries a constant load P applied to the seat as shown. For the angle 8, determine the…

Q: A caisson for closing the entrance to a dry dock is of trapezoidal from 16 m wide at the top and 12…

Q: n H hydraulic cylinder AB

A: P=737Nθ=37 1 Length of LBE and LAB,LBE=4002+1502=427.2mmLAB=100+175+8002+429.22=1156.7mm2 Angles,tan…

Q: 05. Determine the forces in members DE, DI, and Jl of the arched roof truss shown below. -4-6 6 44>…

Q: In engineering, a truss is a structure that "consists of two-force members only, where the members…

A: For the given truss the support at C is roller support and the angle theta is zero. There will be…

Q: Draw the shear and moment diagrams for each of the beams shown.

A: given beams

Q: 6.66 Auniform 80-t pipe that weighs 960 lb is supported entirely by a cable AB of negligible weight.…

A: Given: Pipe length (L)=80 cm Weight(w)=960 kN…

Q: y P2 B P1

A: Drawing the free body diagram of the given truss as shown below – At A the support is fixed and at…

Q: Answer T/F; For the truss below. 30 kips 20' 40 A 30° 60° 23.09 11.55 34.64 T/F Member AC is in…

Q: A mechanism carries a constant load P applied to the seat as shown. For the angle 8, determine the…

Q: 2. Determine the force in members DH and CI. Indicate if the member is in tension or compression. 50…

Q: Question 2: Find the force acting on members AC, BC, and BD of the truss. Specify if the forces are…

A: Find the force in members.

Q: The rod is supported by smooth journal bearings at A, B, and C and is subjected to the two forces F1…

Q: To test the deflection on a uniform 100-kg beam, a boy of who weighs 50 kg exerts a pull of 150N on…

A: Free body diagram: Free body diagram is a diagram that is drawn to determine the unknown forces…

Q: A mechanism carries a constant load P applied to the seat as shown. For the angle 0, determine the…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: 2000 1250 G E F Load, F 750 31.0° 2500 1250 750 C 500 RAX A 33.7 B RBX Dimensions in millimeters RA…

A: The free body diagram of the structure is given below,

Q: 5. A9.0 m beam of uniform width is supported as shown by supports S1 and S2. Given the weight of the…

Q: 7. Compute the internal force of member CD & EF 1000 lb 2000 lb 2000 lb 2000 lb C F 1000 lb D E 30…

Question

Considering the right section

05.
Determine the forces in members DE, DI, and JI of the arched roof truss shown below.
¢4>6 6*4>
4 6 6→4>
| 100
kN
75 kN
75 kN
D
25 kN-
E
25 kN
3
МЕMBER
FORCE (kN)
DE
F
B
DI
JI
K
H
14
G
Dimensions in meters

Expert Solution

Step 1

Step 2

Step by step

Solved in 3 steps with 3 images

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The motorcycle weighs 151 kg and the driver weighs 64 kg. Dimensions l1 = 0,31 m ja l2 = 0,23 m Determine the support force on the rear tire.
Calculate the forces, in Newtons, for the following:(d) member FG(e) pin H(f) hydraulic cylinder AB
Determine the force in each member of the truss (positive value for tension and negative for compression). Given: P1 = 20 N, P2 = 10 N.
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
The motorcycle weighs 151 kg and the driver weighs 64 kg. Dimensions: l1 = 0,31 m and l2 = 0,23 m Determine the support force on the rear tire.
Find the magnitude and location of the resultant force on the cylindrical arc shown in Fig. (10) in each of the following two case: a. Pg=120.11 KPa (abs) b. Pg=90.68 KPa (abs) The arc is 25m long (normal to the paper)
SITUATION 7: Three forces P1, P2, and P3 are acting on a semi-circular structure as shown in Fig. THA-33. Support at A is hinge and support at B is roller. Given: a = 1 m; P1 = 1.8 kN; P2 = 0.9 kN; P3 = 0.45 kN; θ = 30⁰; β = 45⁰. Calculate the resultant of the three forces (in kN). (Answer: 2.45) Calculate the vertical reaction at B (kN). (Answer: 1.06) Calculate the reaction at A. (Answer: 1.63)
Resolve the forces shown in the Figure below to two components Fx and Fy
#1: A moment Macts on the brake drum shown. The radius of the drum is 150 mm. If mu = 0.35 between the drum and belt, calculate the larger tensile force exerted by the belt. Also, determine the magnitude of the braking moment M due to the vertical force P = 120 N.
Which of the following has the dimension for force M1L-3 M L -1 T-2 M-1 L1 T 2 M1 L1 T-2
Determine the forces in each member using any method discussed in your theory of structures/mechanics. Using Software is not allowed. Show complete solution and tabulate your answers indicating whether it is compression or tension. Use Pn = 205 kN, Po = Zero
Find the support reacions and joint force of the construction shown on the figure, if; P=12 kN q=9 kN/m M=12 kN and L=2 m