7 Calculate the magnitude of the force (in kN) onbar AB. Take P = 30.0 kN, do not put units in theanswer. Bars AB and CD are not connected toeach other.5 mAlDPС В6m4 mEF3m2m 3m

Answered: Calculate the magnitude of the force…

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.153P: Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.

See similar textbooks

Similar questions

The 50-ft measuring tape weighs 2.4 lb. Compute the span L of the tape to four significant figures.
The semi circular gate shown in the figure is hinged at B. Determie the force F Required to hold the gate in position? 5088.5 lbs
Calculate all the forces acting on each member of the truss. VERTICAL GRID is equal to 1 meter, and HORIZONTAL GRID is 2.0 m
P1=215 N P2=325 N P3=150 N L1=3m L2=4m 1. Draw a "free body diagram". The diagram should be for members BE, BF, CF, and DF to help solve. 2. What is the force on members CF, BF, BE? Is each of these members having tension or compression?
A woman who weighs 4.92E+2 N is leaning against a smooth vertical wall, as the drawing below shows. As shown, h1 = 1.19 m, h2 = 0.420 m and θ = 59.5°. Calculate the force FN (directed perpendicular to the wall) exerted on her shoulders by the wall.
As shown, a truss is loaded with forces P1= 208 lblb and P2= 397 lb and has the dimension a = 3.70 ft. Determine all of the forces that act on the figure.
In a hydraulic press the diameter of the plunger is 50 mm . Find the diameter of the hydraulic press side when the force at hydraulic press side is 22050 N to lift the weight at the plunger of 450N. a. 350 mm b. 250 mm c. 500 mm d. 100 mm
Consider the truss shown with a 125-lb load on point B. What is the magnitude and direction of the force exerted by the roller support on point E? A. 29.76 lb upwardsB. 95.24 lb upwardsC. 52.79 lb upwardsD. 0 lbE. none of the choices
As shown, three steel wires, each 28 mm2 in area, are used to lift a mass M. Their unstretched lengths are 19.99 m, 19.98 m, and 20 m. If M= 1,182 kg. what stress exists in the MIDDLE wire? Use E=215 Gpa. Answer must be in MPa.
I need to find the forces in each tube but I keep getting stuck. I have been getting really long equations to do algibra onwhich I suspect might be where the error was comming from. The values I have tried are F2 = -0.97786, and -4.889 kips
A 25kg wooden plate is held in place by two strings attached to the ceiling and the wall. The string attached to the ceiling makes an angle 40o with the horizontal and the string attached to the wall makes 90o with the wall. Determine the force in each string (DONT ANSWER THIS PROBLEM). ANSWER ONLY THE PROBLEM IN THE ATTCHED IMAGE, COMPLETE SOLUTION PLEASE.
For the same question, the Driving force (pressing force) of the Nut will be measured with the Torque wrench. While tightening the nut, the contact surface rubs against the fixed surfaces. Accordingly, how much MOMENT do we need to read from the Torque wrench in order to create a force of Fçak=1101 kgf? (Given: Screw pitch M30, Root diameter d1=25.8 mm) Outer diameter of the friction surface under the nut D42 mmFriction coefficient μ=0.6

SEE MORE QUESTIONS

Recommended textbooks for you

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L