0% NaOH feed entering at 100 °F. Evaporation is to be carried out in a single effe aporator for which overall coff. of 500 Btu/hr.ft². F is expected. Saturated stea ailable at 50 psi and the evaporator can be operated available at 10 psi vacuu- horometric pressure of 14.7 psi. BPR = 78 °F using steam table

0% NaOH feed entering at 100 °F. Evaporation is to be carried out in a single effe aporator for which overall coff. of 500 Btu/hr.ft². F is expected. Saturated stea ailable at 50 psi and the evaporator can be operated available at 10 psi vacuu- horometric pressure of 14.7 psi. BPR = 78 °F using steam table

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter45: Domestic Refrigerators And Freezers

Section: Chapter Questions

Problem 8RQ: Frost accumulates on the evaporators of forced-draft refrigerators because A. they are generally...

See similar textbooks

Similar questions

I. Condensing temperature = 40 C II. Evaporating temperature = 5 C III. Temperature of solution entering generator = 80 C IV. Temperature of solution leaving generator = 100 C V. Assume saturated conditions for states 3, 4, 8, and 10. VI. Saturated steam at 0.2 MPa enters the generator and leaves as saturate water: Compute: a. the required mass flow rate of the steam (kg/hr) per kW of refrigeration produced b. the Heat Rejection Ratio, HRR = (Qabsorber + Qcondenser)/Qevaporator of the system.
A cascade system is to be designed to attain a temperature of 213K in an environment of 313K. The refrigerant of the high temperature side is R-134-A and that for low side is R-134-A. The condensing temperature of low side is 5K above the evaporator temperature in the cascade. Compute A.Cop. B.pressure Ratio. C.Mass flow rates of each refrigerant. D.Volume flow rate per TOR. with TS Diagram Using this Steam Table:https://docdro.id/VkxK8WH
b) The high pressure units on a steam plant operate at 10bar (gauge), and the condensate is sub-cooled by 9.5K. If the mass flow rate of condensate is 10 kg/s, use the provided steam tables to determine how much saturated steam at 1.5 bar this condensate could produce. Note it is sufficiently accurate for high pressure condensate, as in this question, to assume that the specific enthalpy is the same as for the saturated liquid at the same temperature.
In a boiler trial, the following observations were recorded:Boiler pressure=10 bar; dryness fraction of steam=0.95; coal consumption=500 kg/h; calorific value of coal=30500 kj/kg; feed water temperature=50oC; feed watersupplied=4 ton/h. Find the evaporation factor and equivalent
The catalogue for a refrigerant 22, four-cylinder, hermetic compressor operating at 29 r/s. a condensing temperature of 40 °C and an evaporating temperature of -4 °C shows a refrigeration capacity of 96.4 kW. At this operating points the motor (whose efficiency is 90 percent) draws 28.9 kW. The bore of the cylinders is 87 mm and the piston stroke is 70 mm. The performance data are based on 8 °C of subcooling of the liquid leaving the condenser. Compute 3.1 the actual volumetric efficiency and 3.2 the compression efficiency.
The percent rating of water tube boiler is 200 %, factor of evaporation is 1.10, and heating surface is 400 ft2. Determine the rate of evaporation, in kg/hr.
The following data are known for Libr-H₂O absorption system. The cooling capacity is 3.5 kW, generation temp. is 82°C, condenser temp. 40°C, evaporator temp. 6°C. Temp. of absorber is 34°C. Assumed saturation condition for strong solution entering generation, weak solution leaving generation and water vapor Leaving evaporator. Properties of solution or water at each point (p, t, h, x), Mass flow rate each point,(COP) act & (COP) tho, Relative COP and Energy balance for all cycle components.
2. Explain how to increase the coefficient of performance of a single stage vapour compression system. Illustrate your analysis through charts (P-h and T-s diagrams)
What is the ideal mass flow rate for a refrigeration and cryogenic plant for oxygen production? Show solution if necessary and reference.
HUMIDIFIER: MASS BALANCE On a hot summer day, the air is at 30.6 ° C and 80% relative humidity. The air conditioning in a building supplies 30 m3 / min of air at 13 ° C to keep the air inside the building at an average temperature of 24 ° C and 40% relative humidity. If the ventilation switch of the air conditioner is “open”, the air from outside enters the unit as shown in the drawing (I): The air conditioner cools the air to a temperature low enough to condense the required amount of water and reheat it to 13 ° C (unsaturated current), at which point it has the same absolute humidity as the air in the building. Calculate: a. the speed at which condenses water (kg / min) b. the temperature at which the air must be cooled to condense water at this rate. Do the calculations without using the psychrometric chart (although 1 atm of current pressure can be assumed). If the ventilation switch is closed, as normal, the air from inside the building would be recirculated in the air…
A. What is the effects of different input parameters on evaporator operating pressure. B. How does the change in evaporator pressure affect the process?
In a certain semiconductor plant, the following condition exist on the intake side of thecompressor:Intake temperature - 28oCRelative humidity - 70%Volume of air drawn - 1,000 m3/hAfter compressing air to 7 bar, temperature rises to 40oC. Determine the following:a) Quantity of water before compressionb) Quantity of water after compressionc) Quantity of water occurring in the production aread) Total amount of water precipitated in the system