1 12 1 2 A pulley with two buckets are set up to pass construction waste from a building under remodeling to the ground level. At the beginning (left diagram) the left bucket has mass 13.0 kg and sits at ground level. The right bucket has mass 18.0 kg and sits at 4.4 m high. The construction worker in the building then let go of the right bucket so the buckets start to move. Ignore friction, how fast are the buckets when the right bucket is about to hit the ground (right diagram)? Your Answer:

1 12 1 2 A pulley with two buckets are set up to pass construction waste from a building under remodeling to the ground level. At the beginning (left diagram) the left bucket has mass 13.0 kg and sits at ground level. The right bucket has mass 18.0 kg and sits at 4.4 m high. The construction worker in the building then let go of the right bucket so the buckets start to move. Ignore friction, how fast are the buckets when the right bucket is about to hit the ground (right diagram)? Your Answer:

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 30RQ: A gas is compressed inside a compressor's cylinder. When the piston is at its bottom dead center,...

See similar textbooks

Similar questions

If an air-conditioning compressor weighing 300lb had tobe lifted 4 ft to be mounted on a base, how much work, in ft-lb. must be done?
Given the sketch below, the diameter of the plunger Dp = 8 cm, the ram diameter is Dr = 48 cm. The efficiency is 100%, the stroke of the plunger is 18 cm. The ram has to raise a load F2 = 2 kN. Find: D) The new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger, the diameter of the plunger is kept to 8 cm.
1, A small ball, mass = 0.60 kg, at the end of a string is whirled in a vertical circle of radius = 60 cm with a tangential velocity of 8.0 m/s. (a) What is the tension in the string when it is at the bottom of the circle? (b) What is the tension in the string when it is at the top of the circle? (c) What is the critical velocity? 2, A cement truck, mass = 2000 kg, has an engine which produces 4000 N. The truck develops a leak and loses cement at a rate of 10 kg/sec, (a) The truck starts from rest and accelerates when the light turns green. What is its initial acceleration? (b) What is the equation for the acceleration as a function of time? (c) What is the equation for the velocity as a function of time? (d) How long will it take the cement truck to get up to a velocity of 15 m/s?
A pulley 1 m in diameter rotating at 300 r.p.m is brought to rest in 80s. By constant force of friction on its shaft. How many revolutions does it moves?
Given the sketch shown below, the diameter of the plunger Dp = 8 cm. The Ram diameter is Dr = 48 cm. The efficiency is 100%, the stroke of the plunger is 18 cm. The ram has to raise a load F2 = 2kN. Find: A) the force f1 exerted on the plunger. B) the number of strokes needed to raise the load given above by a distance of 10 cm. C) the volume of oil pumped if the load moves by 20 cm ( using plunger force in a ) D) what will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 8 cm.
an electric motor driven conveyor belt is required to take 2,200 pounds of dirt, rocks per minute from an excavation site and raise it 15 ft vertically. If all friction in the machinery is neglected, what HP of motor is required?
Given the lifting table shown below , The diameter of the plunger DP 8 cm.The ram diameter DR 48 cm , The efficiency is 100 %, The stroke of the plunger is 18 cm. The ram has to raise a load F2 = 2 kN. Find : a) the force F1 exerted on the plunger b) the number of strokes needed to raise the load given above by a distance of 10 cm c) the volume of oil pumped if the load moves by 20 cm ( using plunger force in a ) d) What will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 8cm .
Given the lifting table shown below, The diameter of the plunger DP 20 cm. The ram diameter DR 60 cm , The efficiency is 100 %, The stroke of the plunger is 30 cm. The ram has to raise a load F2 = 20 kN. Find: a) The force F1 exerted on the plunger b) the number of strokes needed to raise the load given above by a distance of 10 cm . c) the volume of oil pumped if the load moves by 30 cm (using plunger force given in a ) d) What will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 20cm. (please check the picture carefully).
3. In figure, a carton box weighing 5.5 kg is lifted up through a height of 380 mm by a cylinder “A”. Then it is pushed on to a conveyor by a cylinder “B”. The pushing distance is 460 mm. Compressed air is available for this facility at 80 N/cm^2.Find the diameter of the cylinder “A” required to perform thisfunction.(Note: Consider material handling cylinder as ‘A’ and box pushing cylinder as ‘B’).
: what is the required force to move a car (1300 kg) from rest to 80 m (with a 20 m/sec)?
A pull of 20 N at 30° to the horizontal is necesary to move a block of wood on a horizontal table. If the coefficient of friction between the bodies in contact is 0.25, what is the weight of the block?
6.4. A force of 300 N is sufficient to keep a 100-kg wooden crate moving at constant velocity across a wooden floor. What is the coefficient of kinetic friction?