Activity 2 After the completion of the activity one you have been asked to run the test to measure the performance of air compressor a plant equipment given in figure 2.1. Your task is to Produce Specific Steady Flow Energy Equations based on stated assumptions in plant equipment given in the table below in table 1. (D2) Table 1 At inlet Out let P1 1.2 bar P2 7bar C1 6.3m/s C2 5m/s V1 0.98 m3 V2 0.18 m³ 0.4 kg/s 92 kJ/kg 0.4 kg/s 62kW m m AU Air in Air out Water in Air Compressor Water out W Figure 2.1

Activity 2 After the completion of the activity one you have been asked to run the test to measure the performance of air compressor a plant equipment given in figure 2.1. Your task is to Produce Specific Steady Flow Energy Equations based on stated assumptions in plant equipment given in the table below in table 1. (D2) Table 1 At inlet Out let P1 1.2 bar P2 7bar C1 6.3m/s C2 5m/s V1 0.98 m3 V2 0.18 m³ 0.4 kg/s 92 kJ/kg 0.4 kg/s 62kW m m AU Air in Air out Water in Air Compressor Water out W Figure 2.1

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.8P

See similar textbooks

Similar questions

Energy balance results (in kW) obtained for the same medium speed single cylinder diesel engine are reported in the following table. For case 1, if the coolant temperature is 105 °C at the outlet of the engine and the volumetric flow rate is 0.22*10-3 m3/s, the temperature of the coolant at the inlet is (in °C): (The coolant is considered water with a density 999 kg/m3 and a specific heat 4.2 k/kg.K). Case N (rpm) bmep (bar) W. O ambient Q ahast shaft 2.2 4.2 19.1 60.3 9.90 3.52 1 500 7.1 24.5 23.8 500 6.1 3.6 5.2 400 3.50 4.9 4.1 1.4 Select one: O a. 142.1 O b. 112.7 O c. 97.31 O d. 87.2 O e. 370.31
A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the value of (a) expansion work and (b) flow work? If the value is zero, explain why is it so.If it cannot be calculated, explain why.
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Here are the questions to be answered: 1. Why is the value of Wexp 0? (Explain) 2. Given the above values, can you calculate the Wflow? (Yes/No)
Water flows through a horizontal coil heated by steam condensing on the outside. If the inlet pressure and temperature are 2 atm and 160°F (state 1) and at the exit 1 atm and 220°F (state 2), calculate the heat added to the coil per pound mass of water. The entering velocity in 5 ft/s, and the leaving, 500 ft/s. Data: H1=127.9 BTU/lb, H2=1154.4 BTU/lbA. 1031 BTU/lbB. 1042 BTU/lbC. 1048 BTU/lbD. 1052 BTU/lb
HANDWRITTEN AND FINAL ANSWER MUST BE IN ENGLISH UNITS. Show solution. An experimental gas turbine engine is under development to increase its mechanical efficiency. It has a turbine efficiency of 95% and compressor efficiency of 85%. The following parameters are provided: P1 = 550 kPa, T1 = 25 deg C, rp = 5.5, T3 = 1450 deg C, Wnet = 5500 kW. Compute for the (a) flow rate and (b) mean effective pressure. Consider Ethane as your working fluid.
1.1 Determine the electrical power supplied to a boiler when the temperature of the enteringwater is 20 C and the exiting temperature is 89 C. The flow of.the pressured water is 2 Kg/s. There is anegligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specificheat is c = 4,370 J/(Kg K). There is a 1.5(105) W rate of heat loss from the boiler during this process to asurrounding at 293.2 k. Consider steady state conditions.1.2 Calculate the total rate of entropy production in Problem 1.1.1.3 Calculate the total rate of exergy destruction (W) in Problem 1.1. The dead statetemperature is 293.2 K and pressure is 1 bar.1.4 Calculate the mass flowrate of fuel (natural gas, CH4) required to heat the water flow to theconditions of problem 1.1 if the electrical heating device is replaced with a gas fired boiler. The highheating value (HHV) of the fuel is 50.02 MJ/kg.1.5 Calculate the exergy destroyed in the process described by problem 1.4. The exergy…
1.1 Determine the electrical power supplied to a boiler when the temperature of the enteringwater is 20 C and the exiting temperature is 89 C. The flow of.the pressured water is 2 Kg/s. There is anegligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specificheat is c = 4,370 J/(Kg K). There is a 1.5(105) W rate of heat loss from the boiler during this process to asurrounding at 293.2 k. Consider steady state conditions.1.2 Calculate the total rate of entropy production in Problem 1.1.1.3 Calculate the total rate of exergy destruction (W) in Problem 1.1. The dead statetemperature is 293.2 K and pressure is 1 bar.1.4 Calculate the mass flowrate of fuel (natural gas, CH4) required to heat the water flow to theconditions of problem 1.1 if the electrical heating device is replaced with a gas fired boiler. The highheating value (HHV) of the fuel is 50.02 MJ/kg.1.5 Calculate the exergy destroyed in the process described by problem 1.4. The exergy…
A sewage aeration blower running at 3,500 rpm is designed to deliver 34,000 m3/hr of air from 20°C and 1.03 kg/cm2 atmospheric pressure to a discharge pressure of 1.56 kg/cm2 with an efficiency of 70%. On a hot summer day, the atmospheric temperature rises to 43°C but the barometric pressure does not change. It is desired to vary the blower speed to maintain the same discharge pressure. Determine the blower speed, in RPM, for the summer operation.Determine the Brake Horsepower required, assuming that the efficiency remains constant and assume a mechanical efficiency of 0.9 (k = 1.4 for air).Determine corresponding flow in nominal meter cube per hour.
A sewage aeration blower running at 3,500 rpm is designed to deliver 34,000 m3/hr of air from 20°C and 1.03 kg/cm2 atmospheric pressure to a discharge pressure of 1.56 kg/cm2 with an efficiency of 70%. On a hot summer day, the atmospheric temperature rises to 43°C but the barometric pressure does not change. It is desired to vary the blower speed to maintain the same discharge pressure. Determine the blower speed, in RPM, for the summer operation. Determine corresponding flow in nominal meter cube per hour. Determine the Brake Horsepower required, assuming that the efficiency remains constant and assume a mechanical efficiency of 0.9 (k = 1.4 for air).
An ROR hydroelectric power plant is operating under the following conditions:• Plant capacity factor CF = 0.75• Rate of water flow in the turbine Q = 42 m3/s• Water flow velocity v = 12 m/s• Plant electrical efficiency ηel = 0.9 Determine (a) the plant electric power output Pel, and (b) the annual power generation Eyr of the plant.
A double acting compressor with a volume displacement of 0.432 m3/sec, delivers air at 725 KPa at a rate of 0.188 m3/sec. The inlet condition of air 100 KPa and 30 °C and the angular speed of the compressor is 200 RPM. For a compression and expansion processes given by PV1.3=C. Determine: a) The percent clearance of the compressor. b) The bore and stroke, in meters, assuming that the stroke is equal with the bore and the volume displacement of the crank end and head end are the same.
As a mechanical engineering technician, you are asked by your building manager to investigate the performance of a steam turbine at the main university building. Critically compare how heat transfer efficiency will affect the lifetime of the turbine.