1 A frame structure ABCDE as shown below is pin supported at A and roller - supported at C. A trapezoidal distributed force is applied on the section CD of the frame structure. A cable is attached at point F and run through a frictionless pulley attached on the frame structure at point E. The cable is then pulled with a force P in an orientation shown in the figure below. a. Draw the freebody diagram of the structure that you will use to write equilibrium equations b. Calculate the reactions at the pin and roller supports. Please use this numerical information in your calculation: L = 4m, w = 20 N/m, W2 = 10 N/m, P = 100 N L/2 y F E Frictionless pulley P WI L L/4 1/2 D

1 A frame structure ABCDE as shown below is pin supported at A and roller - supported at C. A trapezoidal distributed force is applied on the section CD of the frame structure. A cable is attached at point F and run through a frictionless pulley attached on the frame structure at point E. The cable is then pulled with a force P in an orientation shown in the figure below. a. Draw the freebody diagram of the structure that you will use to write equilibrium equations b. Calculate the reactions at the pin and roller supports. Please use this numerical information in your calculation: L = 4m, w = 20 N/m, W2 = 10 N/m, P = 100 N L/2 y F E Frictionless pulley P WI L L/4 1/2 D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.27P: A 150-lb rigid bar AB. with friction less rollers al each end. is held in the position shown in the...

See similar textbooks

Similar questions

The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces are applied to the handgrips. (Hint: The horizontal components of pin forces at B and D are zero due to symmetry.)
A 150-lb rigid bar AB. with friction less rollers al each end. is held in the position shown in the figure by a continuous cable CAD. The cable is pinned at C and D and runs over a pulley at A. (a) Find reactions at supports A and B. (b) Find the force in the cable.
The space truss ABCD in the shape of a tetrahedron is suspended from three vertical links. Assuming that all connections are ball-and-socket joints, draw the FBD of the truss and count the unknowns.
Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
In Sample Problem 5.4, determine the tension TAC using the equation MDB=0.
The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables attached to points A and C. Find the forces in the cables and the magnitude of the reaction at B. Dimensions Figure P.5.39
Compute the tension TAE in Sample Problem 5.7 using one scalar equilibrium equation.
Repeat Problem 2.5-9 for the flat bar shown in the figure but assume that and that
A uniform rod of weight mg and length L is in equilibrium on a frictionless support as shownin the above figure. Find θ.
a) Figure Q5a shows a truss structure in static equilibrium that is simply supported at A and C. Calculate the reaction forces RA and RC when subjected to vertical loads of 50 kN, 25 kN and 15 kN at nodes D, E & C, respectively. b) For the truss structure in Figure Q5a, determine the forces in members AD and AB; and state whether each of these members are in tension or in compression. *Assume that the truss is in static equilibrium.
Calculate the forces arising on A, B and D pins with the effect of 500N horizontal force in the frame system shown in the figure.