Q6/ A beam AB of span 8m is simply supported at the ends. It carries point loads of 4KN and 8KN at 3m and 4m respectively. It also carries uniformly distributed loads (UDL) of (W) KN/m for 4m from right- end support. If the left end reaction is (19 KN). Find (W) & Right-hand reaction.?

Q6/ A beam AB of span 8m is simply supported at the ends. It carries point loads of 4KN and 8KN at 3m and 4m respectively. It also carries uniformly distributed loads (UDL) of (W) KN/m for 4m from right- end support. If the left end reaction is (19 KN). Find (W) & Right-hand reaction.?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.4.34P: The beam AB shown in the figure is simply supported at A and B and supported on a spring of...

See similar textbooks

Related questions

Q: The tractor shovel carries a 981 N load of soil having a center of mass at G. Compute the force…

A: Internal Forces on Two-Force Members:To keep a structure in equilibrium, internal reactions are…

Q: The machine component from problem 2 (bar with hole and notches) undergoes variable loading from…

A: iven (ultimate tensile strength) = 310 MPa (yield strength) = 275 MPacG (gradient strength factor)…

Q: Flv = lb

A: To determine the reaction force at node 1given diametermoment of inertia length of the beam length…

Q: Carbon dioxide gas is compressed at steady state from a pressure of 1.5 bar and a temperature of 0°C…

A: The mass flow rate of The gas is carbon dioxide.The specific heat of gas is .The inlet condition is…

Q: 4- For the beam shown in Figure, determine the displacements and the slopes at the nodes, the forces…

A: Given:To find:(a) Displacements and the slopes at the nodes.(b) Forces in each element.(c) Reactions…

Q: 1. Water enters a hydraulic jump at 15 m/s with a depth of 3 m. Knowing that C, for water is 1…

A: To Find:the height of the jump.the temperature increase.Given:the inlet velocity is the inlet depth…

Q: A bicycle moves along a straight road such that its speed is described by the continuous function…

Q: A rigid tank contains an ideal gas at 40°C that is being stirred by a paddle wheel. The paddle wheel…

Q: The elastic portion of the tension stress-strain diagram for an aluminum alloy is shown in the…

A: Given ,A alluminium specimen in which guage length = 50 mm and diameter of 12.5 mmLoad applied = 45…

Q: In Betty Crocker's Cookbook, it is stated that it takes 4 h 15 min to roast a 3.2-kg rib initially…

Q: ermine the moment in the beam as a function of x for 4ft<x<10ft B) Determine the shear in

A: The moment equilibrium at point A is-

Q: load is being lifted by moving pulley A downward. If Pulley A starts at the same elevation as pulley…

Q: A Rankine cycle is characterized by turbine inlet conditions of 10 MPa and 500°C. The condenser…

Q: Find the residual hoop stress at the internal surface of a thick-walled cylinder made of a material…

A: Given Data

Q: Go to page 1 vater vapor flowing at a rate of 300.0 mol/h is brought from 600.0 °C and 10 bar to…

Q: Find the centroid and moment of inertia for the allowing about the x and yaxıs

A: Determine the centroid and moment of inertia of the following drawing

Q: Given force F-800 N and section AB is a bar with a diameter d = 0.05 m. Determine the internal…

A: Given :Force, F=800 NDiameter, d=0.05 mSut= 350 MP aSuc= 550 MP aWe have to identify the bending…

Q: The tractor is used to lift the 170-kg load B with the 24-m-long rope, boom, and pulley system. The…

Q: One lbm of R-134a is expanded isentropically in a closed system from 100 psia and 100°F to 10 psia.…

A: Here we will refer to the refrigerant table to get the values of internal energy and entropy and use…

Q: ل Q = 20cfs P - 15 : F, 36in محياه E N { P₂² - 24 in 5° با = 14.7 8 Ps

Q: A tube of porcelain is constrained to expand when it is heated from room temperature (25 °C) to 1000…

A: First, we need to calculate the change in temperature (T) of the porcelain tube.T= final temperature…

Q: 4. Green checkmark visible in this illustration means that: A) Results are ready for review. B)…

A: The green check mark in the illustration means that C. the meshed has passed the quality check.This…

Q: Q3 A mixed-model assembly line has eight stations. Average cycle time is 15 minutes, but times vary…

A: To determine:the production rate for the asynchronous line Given:number of stations are the average…

Q: Problem 5.94 The bar AC is supported by the cable BD and a bearing at A that can rotate about the z…

Q: Q=20 cfs P₁ = 15 psi F₁ Ví 36.m 245 Fiy √₂ F₂ 12 / P₂ = 14.78 psi Solive for both Fix, FMy. F=√ dz…

Q: A sphere of diameter 10 mm and density 7700 kg/ m3 falls under gravity at terminal conditions…

A: To Find:The viscosity.The Reynolds number.The minimum viscosity.Given:the diameter of the sphere is…

Q: 4.17. The free response of a second-order system is illustrated in Figure 4.27. De- termine the…

A: Note:- here some data is required from the graph for the calculations. It may not be exact as actual…

Q: Assume that you are examining the characteristics of a suspension system of a 2000 kg automobile.…

A: For the solution refer below images.

Q: 3. A cable winch is driven by a hydraulic motor and reduction gear, whose transmission ratio i=5.…

A: The hydraulic pressure, p = 240 bar = 240105 N/m2The mass to be lifted, m = 5000 kgThe transmission…

Q: 4 in. 5 in. C G 9 in.- E 45 lb D F -6 in.6 in.- B 120 lb

Q: 8 From the image below, identify the values of the position coordinates A and Buss ging the given…

A: To determine:sAsB

Q: Which of the following diagrams is the correct interaction diagram for the situation described in…

A: Given:To find:Find the correct diagram.

Q: A refrigeration plant that operates on the cycle shown below serves as a water chiller. Data on…

Q: A smooth horizontal pipe with uniform 33 mm diameter has a pressure drop of 44 kPa with a length of…

Q: You have a round power-takeoff shaft guard. The inside diameter of the guard is 3.5 inches. You need…

A: We have round power takeoff shaft(PTO)The inside diameter of the guard is 3.5 inches.Clearance =1/2…

Q: The uniform slender rod AB of weight 8 lb and length 24 in.forms an angle B=30\ [Degree] with the…

A: Here we will apply the moment equation to get the angular velocity

Q: A closed piston-cylinder device contains 2.25 kg of steam at 250.0 °C and 400.0 kPa. The steam is…

Q: USask Engineering Two vehicles, A and B, drive away from each other as seen in the image above. At…

A: This question is based on the concept of relative velocity.

Q: What are different types of lattice defects

A: Lattice defects, also known as crystallographic defects, are irregularities in the arrangement of…

Q: resolve incorrect solution

Q: An Ideal cogeneration steam plant is to generate power and 9400 kJ/s of process heat. Steam enters…

A: heat, inlet temperature into the turbine inlet pressure into the turbine extraction pressure the…

Q: 4. For truss given in a figure below, determine reactions, and forces in all truss members. De-…

A: For truss given in a figure below, determine reactions, and forces in all truss members.Determine…

Q: Two vessels in which the difference of surface levels is maintained constant at 2.4 m are connected…

A: Difference in pressure level,h=2.4 md=75 mmL=15 mf=0.008To determine:The volume rate of flow

Q: Air at 20 C flows over a flat plate with a velocity of 13 m/s. At the leading edge of the plate…

A: To determine:the shear stress on the plate at a distance of 2.68 cm from the leading…

Q: To defrost ice accumulated on the outer surface of an automobile windshield, warm air is blown over…

A: Thickness, t = 5 mmThermal conductivity, k = 1.8 W/m.kOutside temperature, To = -10°CInside…

Q: 2.23 In Fig. P2.23 both fluids are at 20°C. If surface tension effects are negligible. what is the…

Q: R-134a is initially at 600 kPa and 25°C. It undergoes a process during which the entropy is kept…

Q: Air enters the turbine of a gas turbine at 1200 kPa, 1200 K, and expands to 100 kPa in two stages.…

A: Assumptions:Since working fluid in gas turbine cycle is air, hence assume cold air standard analysis…

Q: 1. A thermometer is taken from a room that is 20 °C to the outdoors where the temperature is 5 °C.…

Q: 4. The figure shows a simply supported beam. The beam is subjected to two uniformly distributed…

Concept explainers

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.

Question

Q6/ A beam AB of span 8m is simply supported at the ends. It carries
point loads of 4KN and 8KN at 3m and 4m respectively. It also carries
uniformly distributed loads (UDL) of (W) KN/m for 4m from right-
end support. If the left end reaction is (19 KN). Find (W) & Right-hand
reaction.?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Determine the given data

VIEW

Step 2: Calculate the reaction and w

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

.2 A ligmio.irc ii supported by two vorlical beams consistins: of thin-walled, tapered circular lubes (see ligure part at. for purposes of this analysis, each beam may be represented as a cantilever AB of length L = 8.0 m subjected to a lateral load P = 2.4 kN at the free end. The tubes have a constant thickness ; = 10.0 mm and average diameters dA = 90 mm and dB = 270 mm at ends A and B, re s pec lively. Because the thickness is small compared to the diameters, the moment of inerlia at any cross section may be obtained from the formula / = jrrf3;/8 (see Case 22, Appendix E); therefore, the section modulus mav be obtained from the formula S = trdhlA. (a) At what dislance A from the free end docs the maximum bending stress occur? What is the magnitude trllul of the maximum bending stress? What is the ratio of the maximum stress to the largest stress (b) Repeat part (a) if concentrated load P is applied upward at A and downward uniform load q {-x) = 2PIL is applied over the entire beam as shown in the figure part b What is the ratio of the maximum stress to the stress at the location of maximum moment?
Cantilever beam AB carries an upward uniform load of intensity q1from x = 0 to L/2 (see Fig. a) and a downward uniform load of intensity q from x = L/2 to L. Find q1in terms of q if the resulting moment at A is zero. Draw V and M diagrams for the case of both q and qtas applied loadings. Repeat part (a) for the case of an upward triangularly distributed load with peak intensity q0(see Fig. b). For part (b), find q0, instead of q1
A foot bridge on a hiking trail is constructed using two timber logs each having a diameter d = 0.5 m (see figure a). The bridge is simply supported and has a length L = 4 m. The top of each log is trimmed to form the walking surface (see Fig, b)LA simplified model of the bridge is shown in Fig. g. Each log must carry its own weight w = 1.2 kN/m and the weight (P = 850 N) of a person at mid-span, (see Fig. b). Determine the maximum tensile and compressive stresses in the beam (Fig, b) due to bending. If load h is unchanged, find the maximum permissible value of load ... if the allowable normal stress in tension and compression is 2.5 M Pa.
Beam ACB hangs from two springs, as shown in the figure. The springs have stiffnesses Jt(and k2^ and the beam has flexural rigidity EI. What is the downward displacement of point C, which is at the midpoint of the beam, when the moment MQis applied? Data for the structure are M0 = 7.5 kip-ft, L = 6 ft, EI = 520 kip-ft2, kx= 17 kip/ft, and As = 11 kip/ft. Repeat part (a), but remove Af0 and instead apply uniform load q over the entire beam.
Beam ABC is fixed at support A and rests (at point B) upon the midpoint of beam DE (see part a of the figure). Thus, beam, ABC may be represented as a propped cantilever beam with an overhang BC and a linearly elastic support of stiffness k at point B (see part b of the figure). The distance from A to B is L = 10 ft, the distance from B to C is L/2 = 5 ft, and the length of beam DE is L = 10 ft. Both beams have the same flexural rigidity EI. A concentrated load P = 1700 lb acts at t lie free end of beam ABC. Determine the reactions RA, RB+ and MAfor beam ABC. Also, draw the shear-force and bending-moment diagrams for beam ABC, labeling all critical ordinates.
The beam AB shown in the figure is simply supported at A and B and supported on a spring of stiffness k at its midpoint C. The beam has flexural rigidity EI and length IL. What should be the stiffness k of the spring in order that the maximum bending moment in the beam (due to the uniform load) will have the smallest possible value?
Find expressions for shear force V and moment Mat x = 2L/3 of beam (a) in terms of peak load intensity q0 and beam length variable L. Repeat for beam (b).
The wing of a large commercial jet is represented by a simplified prismatic cantilever beam model with uniform load \v and concentrated loads P at the two engine locations (see figure). Find expressions for the tip deflection and rotation at D in terms of \\\ P, L, and EL.
Beam ABC is loaded by a uniform load q and point load P at joint C. Using the method of superposition, calculate the deflection at joint C. Assume that L = 4 m, a =2ra, q = 15 kN/m, P = 7.5 kN, £ = 200 GPa, and / = 70.8 X 106 mm4.
A propped cantilever beam of a length L is loaded by a concentrated moment M0at midpoint C Use the second-order differential equation of the deflection curve to solve for reactions at A and B. Draw shear-force and bending-moment diagrams for the entire beam. Also find the equations of the deflection curves for both halves of the beam, and draw the deflection curve for the entire beam.
A propped cantilever beam of a length 2L is loaded by a uniformly distributed load with intensity q. The beam is supported at B by a linearly elastic rotational spring with stiffness kR,which provides a resisting moment MBdue to rotation B . Use the method of superposition to solve for all reactions. Also draw shear-force and bending-moment diagrams, labeling all critical ordinates. Let kR= El/L.
The beam AB shown in the figure is simplysupported at A and B and supported on a spring ofstiffness k at its midpoint C. The beam has flexuralrigidity EI and length 2L.What should be the stiffness k of the spring inorder that the maximum bending moment in thebeam (due to the uniform load) will have the smallestpossible value?