1- Assume we have the following active filter with R₂ = 1k02, R₂ = 25k2, R₁ = 15k02, C₂ = 0.2μF, and C₂ = 0.1μF. R Va ww G₁ R ww C₂ HH R₂ ww +Va V. Find the lower frequency and higher frequency in Hz at which the transfer function gain is -3dB. (Hint: the amplitude of transfer function is 0.707)

1- Assume we have the following active filter with R₂ = 1k02, R₂ = 25k2, R₁ = 15k02, C₂ = 0.2μF, and C₂ = 0.1μF. R Va ww G₁ R ww C₂ HH R₂ ww +Va V. Find the lower frequency and higher frequency in Hz at which the transfer function gain is -3dB. (Hint: the amplitude of transfer function is 0.707)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A transducer measures a sinusoidal signal with an amplitude of +-5V and a frequency up to 10Hz. Superimposed on this signal is 60-Hz noise with an amplitude of 0.1V. It is desired to attenuate the 60-Hz signal to less than 10% of its value using Butterworth filter. - Select the filter order n and its cutoff frequency fc. Justify your selections - What is the disadvantage of selecting the filter cutoff frequency, fc to equal the highest frequency output of the measured signal?
Design a Broadband Bandpass Op Amp Filter to provide an amplification of 43 gain within the band of frequencies between 43 Hz and 43 kHz. Use 10 nF for the capacitor CL, use 200 nF for the capacitor CH and 100 Ω for the resistor Ri. Compute the required resistor values RL in Ω, RH in Ω and Rf in Ω. If the input Vi is connected to a 10 mV variable frequency signal, find the magnitude of the output voltage |Vo| in mV at 1 kHz.
a ) Using 0.1 pF capacitors , design an active broadband first - order bandpass filter that has a lower cutoff frequency of 200 Hz , an upper cutoff frequency of 2000 Hz , and a passband gain of 0 dB . b ) Write the transfer function for the scaled filter . c ) Use the transfer function derived in part ( b ) to find H ( wo ) where wo is the center frequency of the filter . d ) What is the passband gain ( in decibels ) of the filter at wo ?
H.W2: a) Using 0.1 µF capacitors, design an active broadband first-order bandpass filter that has a lower cutoff frequency of 200 Hz, an upper cutoff frequency of 2000 Hz, and a passband gain of 0 dB. b) Write the transfer function for the scaled filter. c) Use the transfer function derived in part (b) to find H(jw,)where w, is the center frequency of the filter. d) What is the passband gain (in decibels) of the filter at wo?
Design a high pass filter with a cut of frequency of K1 and a passband gain of K2. Take K1 equal to 27 in kHz and K2 is the 7 (b) Plot the Bode plot of the frequency response of the designed circuit using a python script and validate your answer. (c) How would you increase the passband gain by a factor of five without changing the cutoff frequency?
bandreject filter with a lower cutoff frequency of 400 Hz, an uppercutoff frequency of 4000 Hz, and a passband gain of 0 dB. Use theprototype filter circuits introduced in the design process.2. Draw the circuit diagram of the filter and label all of thecomponents.3. What is the transfer function of the scaled filter?4. Evaluate the transfer function derived in (c) at the center frequencyof the filter. 5. What is the gain (in decibels) at the center frequency?6. Using a computer program of your choice, make a Bode magnitudeplot of the filter transfer function.
a) Draw a simple, single resistor, single capacitor low pass filter. What is the formula for the cut-off frequency for this filter? b) Draw a general graph showing its gain verses frequency with gain in dB vs log of frequency and indicate the cut-off Frequency. c) Draw a simple, single resistor, single capacitor high pass filter. What is the formula for the cut-off frequency for this filter? Draw a graph of its gain verses frequency and label its cut-off frequency.
There is a system that works with a sampling rate of 48 kpsp and requires a bandpass filter that lets the spectral components pass between the fa=12kHz and fb=16kHz sequences. If you are using a 32-tap FIR filter. What is the value of the central frequency, f0, in Hz of the band that passes the filter? And what is the outline of the frequency response for the filter passes bands?
You would like to design the lowpass filter above that has a frequency response shown by the Bode plot below. For a lowpass filter, the passband (the frequency range where signals are passed) is at low frequencies and the stop band (the frequency range where signals are attenuated) is at high frequencies. The corner frequency marks the transition between passband and stopband. If Rf= 5000Ω you will determine the values of R1 and C to complete the design. The design is done in steps. First, determine the corner frequency (or bandwidth) in rad/sec. Enter Wb in the box below. Enter the magnitude of the passband gain, KDC. Recall that a gain in dB is related to the linear gain by the formula KdB = 20log10|k|. Enter the value for R1 in ohms . Enter the value for C in μF.
For a given transfer function of a bandpass filter circuit as shown in the figure For a given transfer function (Take K as 1) Find the center frequency, band-with and the gain for this bandpass filter. 2.Find the cut-off frequencies and the quality for this filter
Show that the circuit behaves as a bandpass filter.(Hint—find the transfer function for this circuit and show that it has thesame form as the transfer function for a bandpass filter. 1. Find the center frequency, bandwidth and gain for this bandpassfilter.2. Find the cutoff frequencies and the quality factor for this bandpassfilter.
The operational amplifier circuit shown in the figure is used as a high pass filter. Assume:C=150nF, Ro=200ΩR1 =2kΩ , R2 =6kΩDetermine:A. The Vo/Vs gain in decibels in the bandwidth.B. The cutoff frequency.