1) Consider the transfer function of a system below. On this transfer function, we do not know the coefficients b and k. For this system we just know the input-output for two cases shown on the right. Please find the coefficients b and k by utilizing the plots on the right. You can extract rough values from the plots. U(s) Y(s) G(s) 1 G(s) 4s2 + bs + k

1) Consider the transfer function of a system below. On this transfer function, we do not know the coefficients b and k. For this system we just know the input-output for two cases shown on the right. Please find the coefficients b and k by utilizing the plots on the right. You can extract rough values from the plots. U(s) Y(s) G(s) 1 G(s) 4s2 + bs + k

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The transfer function of a plant is given by: G(s) = 5 / 0.5s2 + s Design a leading compensator per root locus to bring the closed-loop poles to belocated at s = - 2 ±j3.46.
Given the circuit below, the transfer function Vo/Vi = (1) ______, when the output is the voltage across the capacitor. Using the transfer function, (2) What is the output voltage at t = 0? (3) What is the current through R2 at t = 0? (3) What is the output voltage at time infinity?(4) What is the current through R2 at time infinity?
Find the transfer function of the system using block diagram reduction. Express your transfer function in a form where the coefficient of the highest exponent of s in the denominator is equal to 1. If there is a numerical answer that is nonterminating, it should be expressed up to 2 decimal places only.
1.Draw the s-domain equivalent circuit for the circuit shown in Figure Q1.2 and then find the norton equivalent of the respective circuit you have drawn (with respect to terminal A-B)2.With the help of the Norton equivalent circuit in previous answer, calculate the transfer function for the circuit shown in Figure Q1.2.
Open-loop transfer function of a system is 10 G( s(5s+1) input signal is x{t)=1(t) , Find steady-state error of the system.
The transfer function of a plant is given in the image Design a leading compensator per root locus to bring the closed-loop poles to belocated at s = - 2 ±j3.46.
Measurements conducted on a servomechanism show the system response to be: C (t) = 0.3 e 60t + 1.5 e 10t, when subjected to a unit step input. [1].Obtain the expression for the closed-loop transfer function. [2].Determine the undamped natural frequency and damping ratio of the system.
Consider that the system shown below with H(s)=1 has the following transfer function. Calculate the error constant and steady state error for three basic types of inputs
loop transfer function of the system given in the photo below;( K(s+A)/s(s2+s+B) Find the asymptotes and plot them in the s-plane. Calculate the gain when the two roots are on the imaginary axis. Calculate the angle of separation from the complex poles. draw root locus. A=5 B=4
When 2u (t) is applied to the input of the control system given the transfer function above, the output response of the system is as follows. (U (t) is the unit step function) In this case, what is the rise time of the system? (You can also find it from the graphic
Find the transfer function of the given electrical system below from the state equation. Assume v(t) be the input of the system and the voltage across C be the output of the system. Let X1 be the current flowing on L1, X2 be the voltage across C and X3 be the current flowing on L2.
Root Locus Question Utilizing root locus techniques (by hand) prove that for the transfer function K*G(s) where G(s) = 1/(s^2+s+10) there is no value for K that will allow for less than 16% overshoot. Sketch the region of allowance on the root locus which would give less than 16% overshoot as added proof to the statement 5