1) Derive the shear and bending moment diagram for the following beam loading: A 0000 500 N 500 N B 0.4 m- -0.4 m C D -0.4 m- 2400 N/m 0.3 m a) Using the method of cutting the beam at several points at distance x from A b) Using a method that uses the following relationships between V, w, and M: dv dx = -W V = E dM dx

1) Derive the shear and bending moment diagram for the following beam loading: A 0000 500 N 500 N B 0.4 m- -0.4 m C D -0.4 m- 2400 N/m 0.3 m a) Using the method of cutting the beam at several points at distance x from A b) Using a method that uses the following relationships between V, w, and M: dv dx = -W V = E dM dx

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A simply supported beam, having the following properties: 5.5 m length, Mcr = 30 kN-m, Ig = 7000x10^6 mm^4, Icr = 3000x10^6 mm^4, uniformly distributed dead load = 5 kN/m, uniformly distributed live load = 7 kN/m, Ec = 21,000 MPa. b) Determine the computed value of Ie (DL+LL).
Engr statics I check it was wrong answer 245.166 I need to show all work. Topic: Shear and Bending Moment A gantry crane of weight W-100 Kg moves across a bridge with the length 1-5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations
Let’s consider an overhanging beam subjected to a uniform (rectangular) load with intensity 4 kN/m. The shear diagram is shown by: 4kN/m
For a loaded cantilever beam of uniform cross section, the bending moment along the length is M(x) = 5x2 + 10x, where x is the distance in mm measured from the free end of the beam. What is the magnitude of shear force in the cross section at x = 10 mm.
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown below if P = 1639 N, T = 4678 Nm, a = 0.75 m, b = 1.07 m, c = 0.94 m, w = 44 mm, and h = 75 mm . Round off the final answer to one decimal place.
Consider the beam section below where fc’ = 30 MPa, Es = 200 GPa, determine the bending stress of the steel section if M=180 KN-m in MPa. Express your final answer in two decimal places.
Determine the maximum bending stress (in Pa) for the beam shown belowif P = 1925 N, T = 4796 Nm, a = 0.96 m, b = 0.96 m, c = 0.69 m, w = 42 mm, and h = 77 mm . Round off the final answer to two decimal places.
A gantry crane of weight W=100 Kg moves across a bridge with the length I=5 m. The front axle of the crane (which is nearer end A) carries 3/4W whereas the rear axle (nearer end B) carries 1/4 W. The distance of the axles is b = 1/20. Determine the maximum value of the bending moment and enter your answer in N-m units.. Remember to also show all your work (FBDs, calculation steps, etc on the handworked file) HINT: Determine the shear and bending moment equations along the beam. Assume only concentrated loads at the front and rear axles.
The rate of change of Bending Moment “M” with respect to distance “x” in a beam is known as ________________ Rate of loading Slope of the beam Shear force Deflection of the beam
PLEASE ?? ANSWER ?Part 1 For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A) Let a= 3.00 m, b= S.00 m. PB= 35kN, and PC = 65kN. Construct the shear force and bending-moment diagrams on paper and use t he results to answer the quest ions in the subsequent parts of this GO exercise. Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Please Answer: Ay = kN Dy = kN ?Part 2 Determine the shear force acting at each of the following locations: (a)x = 2 m (b)x =4m (c). x = 8 m Note that x = 0 at support A When entering your answers. use the shear-force sign convention detailed in Section 7.2. Please Answer: (a) V= kN (b) V=…
N for Newton, m for meter, mm for millimeter, N/(mm^2) for Stress, mm^2 or m^2 for Area, mm^4 for Moment of inertia and Nm for bending moment. Use brackets if the power is MINUS for Example: 0.00125 N =1.25*10^(-3)N. A beam has a bending moment of 3 kN-m applied to a section with a hollow circular cross-section of external diameter 3.4 cm and internal diameter 2.4 cm . The modulus of elasticity for the material is 210 x 109 N/m2. Calculate the radius of curvature and maximum bending stress. Also, calculate the stress at the point at 0.6 cm from the neutral axis Solution: (i) The moment of inertia = ii) The radius of curvature is (iii) The maximum bending stress is iv) The bending stress at the point 0.6 cm from the neutral axis is
without writing shear equations, draw the shear diagrams for the Beam loaded as shown in Fig. 2KN/m