1- Determine the magnitude and direction of the moment of the force of the movement if the force at A about point P. a- Mp = 1440 NmC %3D b- Mp = 1440 Nm 9 4 m %3D 2 m c- Mp = 600 NmC 13. 12 d- Mp = 600 Nm Ɔ %3D 260 N 3- The refrigerator has a weight of 200 lb and a center of gravity at G. Determine the force P required to move it. Will the refrigerator tip or slip? Take H = 0.4. a- P = 80 lb Slips b- P = 75 lb Tips 4 ft 1.5 ft 3 ft c- P = 75 lb Slips d- P = 80 lb Tips 3 ft

1- Determine the magnitude and direction of the moment of the force of the movement if the force at A about point P. a- Mp = 1440 NmC %3D b- Mp = 1440 Nm 9 4 m %3D 2 m c- Mp = 600 NmC 13. 12 d- Mp = 600 Nm Ɔ %3D 260 N 3- The refrigerator has a weight of 200 lb and a center of gravity at G. Determine the force P required to move it. Will the refrigerator tip or slip? Take H = 0.4. a- P = 80 lb Slips b- P = 75 lb Tips 4 ft 1.5 ft 3 ft c- P = 75 lb Slips d- P = 80 lb Tips 3 ft

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter2: Basic Operations With Force Systems

Section: Chapter Questions

Problem 2.91P: (a) Replace the force F=2800i+1600j+3000klb acting at end A of the crank handle with a force R...

See similar textbooks

Similar questions

A man holds a 192-N ball in his hand, with the forearm horizontal (see the figure). He can support the ball in this position because of the flexor muscle force M→, which is applied perpendicular to the forearm. The forearm weighs 18.5 N and has a center of gravity as indicated. Find (a) the magnitude of M→ and the (b) magnitude and (c) direction (as a positive angle counterclockwise from horizontal) of the force applied by the upper arm bone to the forearm at the elbow joint. For the direction I know the units is degrees, but I have tried using the answer from b, and it is not correct.
At the shown position, the ground reaction forces measured using a force platform are 600N in the vertical direction (Fy) and 200N in horizontal direction (Fx). The mass of the limb below the knee is 4kg with the centre of gravity at the point G. Determine the forces and moment applied to the knee joint. Draw correct free body diagram using any part of the body shown below.
ew Policies irrent Attempt in Progress With the 255-Ib cylindrical part P in its grip, the robotic arm pivots about O through the range -45° ≤ 0 ≤ 45° with the angle at A locked at 120° Determine and plot (as a function of 8) the moment at O due to the combined effects of the 255-Ib part P, the 145-Ib weight of member A (mass center at G4), and the 35-Ib,weight of member AB (mass center at G). The end grip is included as a part of member AB. The lengths Ly and Ly are 2.8 ft and 2.4 ft, respectively. What is the maximum absolute value of Mo and at what value of f does this maximum occur? The moment is positive if counterclockwise, negative if clockwise. After you have the plot, answer the questions.
#1: A moment Macts on the brake drum shown. The radius of the drum is 150 mm. If mu = 0.35 between the drum and belt, calculate the larger tensile force exerted by the belt. Also, determine the magnitude of the braking moment M due to the vertical force P = 120 N.
Determine the moment MAB produced by the force F shown in the figure which tends to rotate the bar about the axis AB.
Crane boom of mass 450 kg with its center of mass at C isstabilized by two cables AQ and BQ. The crane boom lies in the y–zplane. Find the forces in each cable (P=20 kN)
1. Determine the largest value of couple moment MM just before the disk begins to slip. (answer is lb*ft) 2. At the moment before the disk begins to slip (impending motion), determine the magnitude of the normal force at point A, otherwise known as NA. (answer is lb) 3. At the moment before the disk begins to slip (impending motion), determine the magnitude of the normal force at point BB, otherwise known as NB. (answer is lb)
If the 15 kg bar has a center of mass at G, calculate the resulting moment at point O.
The pumping unit is used to recover oil. When the walking beam ABC is horizontal, the forceacting in the wireline at the well head is 250 lb. Determine the torque M which must beexerted by the motor in order to overcome this load. The horse-head C weighs 60 lb andhas a center of gravity at Gc. The walking beam ABC has a weight of 130 lb and a centerof gravity at GB, and the counterweight has a weight of 200 lb and a center of gravity atGW. The pitman, AD, is pin connected at its ends and has negligible weight.
The jib crane is designed for a maximum capacity of 7 kN, and its uniform I-beam has a mass of 240 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.7 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work.(a) What is the value of R when x = 1.9 m?(b) What is the value of R when x = 3.2 m?(c) Determine the minimum value of R and the corresponding value of x.(d) For what value of R should the pin at A be designed?
Q4: of a car غطاء محرك The i Jul. The bonnet is held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The long, has a weight of 25 N and its center diagram shows the open bonnet bonnet is 0.90 m of gravity G is 0.35 m from the hinge at O. 1) On the diagram, draw and label the two forces other than V acting on the bonnet. By taking moments about A, Proof that the vertical 2) force V applied at the end of the bonnet is 9.7 N. 3) Calculate the magnitude of the force acting at the hinge ON.
Determine A·(B×C) The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 11i - 10j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN Determine the magnitude of the moment of P about the origin (point O) in Nm.