1 m/s 4 m/s 30 m 15 m Fan 30 m 15 m 60 m 3 m/s For the duct system shown, determine the size of ducts AB, BC and CD using equal friction method . Assume friction rate of 0.09 mm of water per m length of duct. Use following correlation for friction rate Др, = 2.454 x100 mm of water /m where Q is in m/ s andD is in m. 1.623 4.832

1 m/s 4 m/s 30 m 15 m Fan 30 m 15 m 60 m 3 m/s For the duct system shown, determine the size of ducts AB, BC and CD using equal friction method . Assume friction rate of 0.09 mm of water per m length of duct. Use following correlation for friction rate Др, = 2.454 x100 mm of water /m where Q is in m/ s andD is in m. 1.623 4.832

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A hydroelectric plant has 20 MW generator with an efficiency of 96 %. The generatoris directly coupled to a vertical Francis type hydraulic turbine having an efficiency of 80%.The total gross head on the turbine is 150 m while the loss of head due to friction is 4 %of the gross head, the runaway is not to exceed 750 rpm. Determine the flow of waterthrough the turbine in m3/s. Complete Solution/s (i.e. transformations, equivalent formula, etc).
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m.The total length and diameter of the suction and discharge pipes are 500 mm, 1500 m and 30 mm, 1000 m respectively. Assume a head lose of 2 meters per 100 m length of the suction pipe and 3 m per 100 m length of the discharge pipe. What is the required horsepower of the pump? **provide complete solution using bernoullis equation..provide illustration with labels like datum line and such** Show all formula derivation
The head-versus-flow-rate characteristics of a centrifugalpump are shown in Fig.. If this pump drives water at20°C through 120 m of 30-cm-diameter cast iron pipe,what will be the resulting flow rate, in m3/s?
In a 225 mm pipeline 0.14 m3/s of water are pumped from a reservoir of surface elevation30 over a hill of elevation 50. A pump of what power is required to maintain a pressure of 345kPa on the hilltop if the head lost between reservoir and hilltop is 6 m?
A fully-filled open storage tower of height 32 m and diameter 3.0m supplies water to a house. A horizontal pipe at the base of the tower has a diameter of 2.54cm. To satisfy the needs of the home, the supply pipe must be able to deliver water at a rate of 0.67 gal/s. a. If water were flowing at the maximum rate, what would be the pressure in the horizontal pipe?b. A smaller pipe, of diameter 1.27 cm supplies the second floor of the house, a distance of 7.2 m above the ground level. What are the flow speed and water pressure in this pipe?
9. Find the discharge through a rectangular orifice 2.2 m wide and 1.3 m deep fitted to a casier tank. The water level in a team is 2.5 m above the top edge of orifice. 10. Find the discharge through a rectangular orifice 3.2 m wide and 1.7 m deep fitted to a casier tank. The water level in a team is 3.3 m above the top edge of orifice. Take Cd = 0.6 i 11. Loss of head due to friction is a) Inversely proportional to velocity b) Inversely proportional to hydraulic radius d) Directly proportional to gravitational constant b) Directly proportional to hydraulic radius 12. Which among the following does not depend on the friction factor? a) Pipe diameter b) Fluid density ¢) Viscosity d) Weight 12. How do we calculate losses for a larger range of Reynolds number? a) Scatter chart b) Bar chart ¢) Moody chart d) Column histogram ) is formula for friction factor of circular pipes? 14. Which of the following equations is a result of momentum conservation for inviscid steady flows? a) Bernoulli's…
The head-discharge characteristic relationship of a pump is given by:H = 40 - 200*Q^2, where H is the total head generated by the pump in meters and Q is the discharge in m^3/s. The pump lifts water through a pipe 0.3 meter diameter over a distance of 1000 meters against a static lift of 25 meters. Find the operating/ duty point (H and Q) if the friction coefficient of the pipe 'f ' is 0.03.
In a pipe of diameter 300mm the center line velocity and the velocity at a point 100mm from the center, as measured by pitot tube are 2.4 m/s and 2.0 m/s respectively. Assume the flow in the pipe to be turbulent find: 1-Dischrge through the pipe,2-Coefficient of friction, 3 Height of roughness projections.Please do not waste my question solve with correct answers only.
The hydroelectric facility that has been proposed will consist of a turbine with anefficiency of 89.2%. The facility will be located at a vertical depth of 14.8 m belowthe riverbed. The river flows with the following properties:o hydraulic diameter of 6.25 mo slope of 0.031o wetted perimeter of 12.2 mo a Chezy coefficient of 4.85 m0-5s1.Thedensity of the river water is 998.2 kg m3, and the acceleration due to gravity is9.81 m s2.Assuming that the turbine operates for 94.0% of the time and one year isapproximately 3.1536 x 107s, calculate:i. the mass flow rate of the river(5 marks)ii. the maximum energy that could be extracted annually from the river flow.
Estimate pump power requirement for Hpump = 58.598 m and npump = 0.60. Use the following: v = 1 x 10-6 m2/s Kentrance = 0.5 Kexit = 1 Kelbow = 0.26 f = 0.019 γ = 9810 N/m3 Choices: 197 kW 179 kW 279 kW 297 kW None of the Choices
Please indicate the given and illustration A steel pipe, 3.5 km long x 80 cm diameter x 1 cm wall thickness, conveys water at the rate of 1.75 m3/s. Determine the increase in pressure when a valve provided at the downstream end of the pipe is closed instantaneously. Consider pipe to be elastic and take bulk modulus of water K = 2x109 N/m2; Modulus of elasticity of steel E = 2x1011 N/m2. After determining the surge of pressure in the pipe, compute the following: A) The Longitudinal Stress of the Pipe in Pascal. B) The Circumferential Stress of the Pipe in Pascal.
The head-discharge relationship for a certain pump can be represented by the equation H-29-6Q^2 The pump is fixed 2 m shove the water surface tank at a level 10 m above the pump. The suction and delivery pipes are 12 m and 720 m long, respectively and each pipe is 0.5 m in diameter. The Estimate the discharge (in m³/s) at the best operating point for the pumping system,