Outlet Inlet

Q: Liquid ethanol (density is 815 kg/m^3) at a pressure of 235 kPa enters a 12-cm-diameter pipe at a…

A:

Q: Oil with p = 865 kg/m³ and µ = 0.24 kg/m. s is flowing through a 2 cm diameter pipe that discharges…

A: Given Density = 865 kg/m3 Viscosity coefficient = 0.24 kg/ms Diameter of the pipe = 2cm = 0.02 m…

Q: A U-tube open at both ends is partially filled with water. Oil having a density of 750 kg/m3 is then…

A:

Q: Water is flowing through a 10-cm-diameter water pipe at a rate of 0.1 m3/s. Now a diffuser with an…

A: Given: The of pipe at the section of bolt, d = 10 cm The diameter of the pipe at the exit, D = 20 cm…

Q: Oil with ? = 876 kg/m3 and ? = 0.24 kg/m·s is flowing through a 1.5-cm-diameter pipe that discharges…

A: Given data Determine the flow rate of oil through the pipe if the pipe is (a) horizontal (b)…

Q: A very large tank contains air at 102 kPa at a location where the atmospheric air is at 100 kPa and…

A: Write the given data. Write the properties of air at 20°C.

Q: Steam at 0.7Mpa and 250'c expands in a nozzle to 0.1Mpa. Determine the throat and nozzle exit cross…

A:

Q: Consider a centrifugal blower that has a radius of 20 cm and a blade width of 8.2 cm at the impeller…

A:

Q: A pressurized tank of water has a 10-cm-diameter orifice at the bottom, where water discharges to…

A:

Q: the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle is operating steadily…

A:

Q: Consider the flow of oil with ? = 894 kg/m3 and ? = 2.33 kg/m·s in a 28-cmdiameter pipeline at an…

A: Write the given data.

Q: at a point upstream of the throat in a converging-diverging nozzle the velocity temperature and…

A: Given Datau1=192m/sT1=41°Ck=1.4A'=0.03m2P1=282kPa

Q: In a pipeline with converging diameter, will the gradient of the total energy line be steeper or…

A: In a converging pipe, the equation of continuity for incompressible flow can be written as,…

Q: A very large tank contains air at 102 kPa at a location where the atmospheric air is at 100 kPa and…

A: Pressure of air in the tank Pa = 102 kPa Atmospheric pressure, Patm = 100 kPa Temperature, T= 20°C…

Q: Air enters a 5.5-cm-diameter adiabatic duct with inlet conditions of Ma1 = 2.2, T1 = 250 K, and P1 =…

A: Write the values of pressure ratio and temperature ratio at duct inlet corresponding to the Mach…

Q: A pipe carrying water has an inlet of diameter 0.18 m and an outlet which is 1.11 m below the inlet…

A:

Q: Air enters a compressor with a stagnation pressure of 100 kPa and a stagnation temperature of 35°C,…

A: Given: The initial stagnation pressure of the air is P1=100 kPa. The final stagnation pressure of…

Q: Consider water flow through a horizontal, short garden hose at a rate of 30 kg/min. The velocity at…

A: Given: The mass flow rate of the water, m = 30 kg/min The inlet velocity of the water, v1 = 1.5 m/s…

Q: The power available in a jet having a cross-sectional area of 0.005 m2 with a velocity of 25.8 m/s

A:

Q: Water is flowing through a 15-cm-diameter pipe that consists of a 3-m-long vertical and 2-m-long…

A: Given Data: The diameter of pipe is d = 15 cm. Velocity of water leaving is v = 5 m/s. The mass of…

Q: Consider a centrifugal blower that has a radius of 20 cm and a blade width of 8.2 cm at the…

A: Given data: The radius of the centrifugal blower at the inlet to the impeller is r1 = 20 cm = 0.20…

Q: The liquid storage tank shown in Figure 4 has two inlet streams with mass flow rates F1 and F2 and…

A:

Q: Water flows through a 90 degree elbow connected to a pipe with diameter of 1.5 cm. At inlet pressure…

A:

Q: Air is flowing through a venture-meter whose diameter is 2.6 in at the entrance part (location 1)…

A:

Q: Air enters a 12-cm-diameter adiabatic duct with inlet conditions of V1 = 150 m/s, T1 = 500 K, and P1…

A: Write the formula to calculate the speed of sound at the inlet. c1=kRT1 Here, T1 is the inlet…

Q: The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle…

A: for solution refer below images.

Q: A 6-cm-diameter horizontal water pipe expands gradually to a 9-cm-diameter pipe. The walls of the…

A: It is given Density of water = 1000 kg/m^3 Total inclined angle =60° If mass flow rate same We can…

Q: Orange juice is flowing through a horizontal U-type reducing bend at a rate of 36kg/s. The…

A: We have to determine the force applied to the reducing bend by the orange juice in the horizontal…

Q: Air at 100 kPa and 25°C flows in a horizontal duct of variable cross section. The water column in…

A: Given : The pressure inlet = 100 kPa The air temperature = 25°C The difference in the height of…

Q: The compressed air requirements of a textile factory are met by a large compressor that draws in 0.6…

A: Given: The value of volumetric flow rate at the inlet is, Qin=0.6 m3s. The diameter of the…

Q: A 6-cm-diameter horizontal water pipe expands gradually to a 9-cm-diameter pipe. The walls of the…

A: Given data D1=6 cmD2=9 cmP1=150 KPaV1=150 m/s

Q: • R-134a enters a nozzle at 700 kPa and 120 °C and exits at 400 kPa and 30°C. Mass flows steadily…

A:

Q: Air flows through a 6-in-diameter, 50-ft-long adiabatic duct with inlet conditions of V1 = 500 ft/s,…

A: Given, D1 = 6 in L1 = 50 ft V1 = 500 ft/s T01 = 650 R P1 = 50 psia f = 0.02

Q: Air enters a compressor at a temperature of 70•C and a pressure of 10 kPa. At the exit of the…

A:

Q: The compressed air requirements of a textile factory are met by a large compressor that draws in 0.6…

A: Properties of air at 60 degrees Celsius are: The roughness of the galvanized steel pipe is Given…

Q: Water is flowing in a 5 cm diameter pipe at a velocity of 5 m/s. The pipe expands to a 10 cm…

A:

Q: The compressed air requirements of a textile factory are met by a large compressor that draws in 0.6…

A: Properties of air at 60 degrees Celsius are: The roughness of the galvanized steel pipe is Given…

Q: What is the effect of friction on the entropy of the fluid during Fanno flow?

A: According to the Second law of thermodynamics, entropy must always increase for Fanno flow.

Q: Water flows at a rate of 0.035 m3/s in a horizontal pipe whose diameter is reduced from 15 cm to 8…

A: Given   Diameter, D = 15 cm                  d = 8 cm Flow rate, Q = 0.035 m3/s Find   Head loss, h

Q: calculate the outlet velocity (V2) of water by using continuity and Bernoulli’s equation.

A: Given: Density (ρ) =750 kg/m3 Inlet conditions: d1= 8 cm =0.08 mP1= 400 kPaOutlet condition: d2=4 cm…

Q: - Air at 105 kPa and 37°C flows upward through a 6-cm-diameter inclined duct at a rate of Q (L/s).…

A:

Q: What is the effect of heat gain and heat loss on the entropy of the fluid during Rayleigh flow?

A: Rayleigh flow is basically friction less, non adiabatic flow through a constant area duct.

Q: A 400cm long pipe with a smaller diameter of 3.937 inchesand a larger diameter of 11.81 inches as…

A:

Q: Air enters a 7-m-long section of a rectangular duct of cross section 15 cm × 20 cm made of…

A:

Q: Determine the stopping temperature and stopping pressure for the following substances and flow…

A: (A) Given Data Temperature of helium is : T=50°C Pressure of helium is : P=0.15 MPa Velocity of…

Q: The liquid storage tank shown in Fig has two inlet streams with mass flow rates w1 and w2 and an…

A: Given that, Height of storage tank, h=2.5 m,Diameter of storage tank, D=2 m,Density of liquid, ρ=800…

Q: Water is flowing through a 10-cm-diameter water pipe at a rate of 0.1 m3/s. Now a diffuser with an…

A: Solution: Given data: d = 10 cm D = 20 cm Q = 0.1 m3/s

Q: Air is flowing through a venture-meter whose diameter is 2.6 in at the entrance part (location 1)…

A: Given Data: The diameter at the entrance is, d1=2.6 in. The diameter at the throat is, d2=1.8 in.…

Q: 3. Water is flowing through a 15 cm diameter pipe that consists of a 3 m long vertical and 2 m long…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.