i need the answer quickly 1. A 240 V, 50 Hz, single-phase capacitor start a.c. motor is loaded such that the slip is 6 %. The motorconstants referred to the stator are :Stator resistance 2-2 2; Rotor resistance 3-8 23.02; Rotor reactance86 2; Iron and friction loss = 50 WDraw the equivalent circuit and from it find the output power and efficiency at the given loading.Stator reactance2.12Magnetising reactance =[1090 W; 74-6 %]

Answered: Image /qna-images/answer/6790659f-4b69-4598-a955-4baa42a17ffe.jpg

1. A 240 V, 50 Hz, single-phasc capacitor start a.c. motor is loaded such that the slip is 6 %. The motor constants referred to the stator are : Stator resistance 2-2 2; Rotor resistance 3-8 2 3.02; Rotor reactance = 86 N ; Iron and friction loss = 50 W Draw the equivalent circuit and from it find the output power and efficiency at the given loading. Stator reactance 2.12 Magnetising reactance = [1090 W; 74-6 %]

1. A 240 V, 50 Hz, single-phasc capacitor start a.c. motor is loaded such that the slip is 6 %. The motor constants referred to the stator are : Stator resistance 2-2 2; Rotor resistance 3-8 2 3.02; Rotor reactance = 86 N ; Iron and friction loss = 50 W Draw the equivalent circuit and from it find the output power and efficiency at the given loading. Stator reactance 2.12 Magnetising reactance = [1090 W; 74-6 %]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 110V shunt generator has a full load current of 100A, shunt field resistance of 55 ohms and constant losses of 500W. If full load efficiency is 88%, find the armature resistance. Assuming voltage to be constant at 110V, calculate the efficiency at half load. Find the load current.
A separately excited D.C motor is rated for a full load torque of 100Nm. For an applied voltage of 240V and for flux (φ) per pole of 30 mWb, the no-load and full load speeds of the motor are 1595 r.p.m and 1195 r.p.m respectively. (a) Find the armature resistance (b) If the applied voltage and the flux per pole are reduced to 200V and 20mWb respectively, Find the corresponding full load speed.
A three-phase 60 Hz induction motor connected to a three-phase bus at rated voltage isoperating at a low slip condition (i.e s < 20%) resulting in a steady state speed of 1090 rpm.(a) How many poles does the motor have?(b) What is the percentage slip at the operating speed?(c) What is the corresponding frequency, (fr) of the currents and voltages induced in therotor winding?
Q1) A 4-pole, separately excited, wave wound DC machine with 0.12 armature resistance is rated for 230 V and 5 kW at a speed of 1200 rpm. If the same armature coils are reconnected to forms a lap winding, what is the power (in kW) at 1200 rpm of the reconnected machine if the field circuit is left unchanged? Also voltage regulation in both cases
A four-pole, three-phase induction motor rotatesat 1,700 r/min when the load is 100 N-m. The motoris 88 percent efficient.a. Determine the slip at this operating condition.b. For a constant-power, 10-kW load, determine theoperating speed of the machine.c. Sketch the motor and load torque–speed curves onthe same graph. Show numerical values.d. What is the total power consumed by themotor?
A long shunt compound generator delivers 100 A at 250 V. The armature, shunt field and series field resistances are 0.02 Ohms, 50 Ohms and 0.05 Ohms respectively. If the Break Horse Power (BHP) or the power developed by the shaft torque of the driving engine is 40, determine the stray loss.
Three-phase 460-hp, 415 V, 4-pole, 50 Hz induction motor is operating at overvoltage of 480 V and reduced load of 80% of the rated value and draws a line current of 624.06A. The losses at these operating conditions are as follows: The stator conductor loss is 12.6kW, the rotor conductor loss is 10.4kW, the core loss is 11.00kW; and rotational losses is 4.129 kW. Sketch the power flow diagram, enter the known values, and determine (a) rotor speed (b) shaft output torque (c) developed mechanical torque in Nm. (d) input power to the stator; (f) the input power factor. Do only part (a), (b) & (c)
The armature winding resistance of a long shunt connected DC generator is 0.4ohm, the resistances of the shunt and serial field windings are 125 ohms and 0.1 ohms, respectively. While the generator supplies 8KW of power to the load it feeds, which is the voltage it produces since the output voltage is 250V?
Three-phase induction motor, 460 V 50 Hz, 4 poles, 50 hp with Delta, operating at 3.8% slip rated torque when receives Line Voltage 460 V, 50 Hz The parameters of the equivalent circuit per phase are as follows.R1 = 0.33, X1 = X2 = 0.42 and Xm = 30 Ohm / phase.Answer the following questions by neglecting the mechanical losses, Core losses and Stray load losses.A) Value of the rotor resistance R2 B) Maximum torque and rated speed C) line current and starting torque of motor
A 240 V, Short – Shunt DC Generator supplies a load current of 60 A. The armature circuit resistance is 0.10 Ohms and shunt-field circuit resistance is 120 Ohms. The series-field resistance is 0.08 Ohms. Calculate The developed Power The percentage voltage regulation. Draw the power flow graph, showing the various losses as well the input, developed, and output power values. P rotational = 500W
A 110-V shunt generator has a full load current of 100 A, shunt field resistance of 55 Ω and constant losses of 500 W. If F.L. efficiency is 88%, find armature resistance. Assuming voltage to be constant at 110 V, calculate the efficiency at half-F.L. and at 50% overload. Find the load current corresponding to maximum efficiency.
Q1) A 4-pole, separately excited, wave wound DC machine with 0.12 armature resistance is rated for 230 V and 5 kW at a speed of 1200 rpm. If the same armature coils are reconnected to forms a lap winding, what is the power (in kW) at 1200 rpm of the reconnected machine if the field circuit is left unchanged? Also calculate the voltage regulation in both cases