Answered: 1. A 7.5 -mm-diameter drill is used on…

1. A 7.5 -mm-diameter drill is used on a drill press operating at 300 rpm. If the feed is 0.125 mm/rev, what is the MRR? What is the MRR if the drill diameter is doubled?

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter4: Drill Press

Section4.1: Introduction To The Drill Press

Problem 3RQ: Explain how the size of an upright drill press is determined.

See similar textbooks

Related questions

Q: Q3). A block of 190mm length and 100mm width is to be machined in shaping process. The permissible…

Q: lathe machine, the maximum torque transmitted by a shaft exceeds the mean torque by 11 %. A power of…

A: For solution refer below images.

Q: A 200 mm long magnesium alloy bar, 63 mm in diameter is turned on a lathe using a high speed steel…

A: Given data, Length of the magnesium alloy bar, L = 200 mm Diameter of the bar, D = 63 mm Velocity of…

Q: Calculate the machining time required for making 60 holes on an MS plate of 80 mm thickness with a…

A: Given data⇒ Number of holes (n)= 60 The thickness of Mild steel plate (t)=80 mm Diameter of the…

Q: An external turning operation is performed on a hollow workpiece of 200 mm external diameter and 100…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: 20 mm through hole is to be drilled in a 30 mm thick plate using a double fluted, 120° lip angle…

A: Given:hole diameter, d=20 mmthickness of plate, t=30 mmspeed of drill, N=500 rpmapproach=3…

Q: A cast iron component for motorcycle is to be tumed with machine settings of feed = 0.22 mm/rev, and…

A: Surface roughness is calculated. If you liked my solution, I would really appreciate a LIKE, please…

Q: A 16mm Solid carbide tool with two teeth is used to machine Aluminium using the cutting speed of…

Q: It is required to reduce the thickness of cast iron workpiece with dimensions (L x w x t) of (230 mm…

Q: 4) The workpiece material is copper alloy. Assume that D=220 mm, w = 40 mm, 1= 550 mm, d=2 mm, v=1…

A: Given Data The diameter is:D=220 mm The width of cut is:w=40 mm The length of the cut is:l=550 mm…

Q: is speed important in a drilling operation ? What are the results of a drill bit with unequal lips ?…

Q: For a turning operation using a ceramic cutting tool, if the speed is increased by 50%, by what…

A: Tool life is the time duration during which a tool can perform its action without any kind of…

Q: 3. A turning operation is carried out on aluminum (100 BHN), the cutting conditions are: v = 5.6…

Q: Calculate the time required to machine a workpiece 170 mm long, 60 mm diameter to 165 mm long 50 mm…

A: Given:L1=170 mmL2=165 mmD1=60 mmD2=50 mmN=440 rpmf=0.3 mm/revd=2 mmApproach and overtravel=5 mm

Q: Calculate the machining time to complete the job as shown below from a bar 120 mm long and 60 mm…

A: Given: length of the job→L=120 mm initial diameter→D=60 mm maximum depth of cut→d=5 mm hence in…

Q: Example 2 Calculate the r/min at which a drill press should be set to make threading for M12 x 1.75…

A: Given- material - cast iron M12 x 1.75 Diameter of workpiece (D)= 12 mm Feed = Pitch of Thread =…

Q: In orthogonal turning of a low carbon steel bar of diameter 150 mm with uncoated carbide tool. the…

Q: 4) Assuming that the coefficient þf friction is 0.25, calculate the maximum depth of cut for turning…

A: The power of lathe is given as, The coefficient of friction is given as, The mechanical efficiency…

Q: In a turning operation, the workpiece diameter is Dm-40.00 mm and the diameter after the operation…

A: GIVEN DATA - D=40mm D2=24mm V=132m/min f=0.03mm/rev WE HAVE TO CALCULATE MRR

Q: Problem1. In orthogonal tuming of a 50mm dia. mild steel bar on a lathe, the following data were…

A: Given data: The rake angle, α = 15o. The cutting speed, Vc = 100 m/min. The feed rate, f = 0.2…

Q: A job has to be machined in shaping and the process parameters are given below: a. Length of…

Q: A cylindrical work bar with 4.5 in diameter and 52 in length is chucked in an engine lathe and…

A: (a) The depth of cut is, d = 0.125 in. (b) The required feed is, f = 0.010 in/rev. (c) The cutting…

Q: In a turning operation on carbon steel with hardness- 175 HB. the cutting speed - 225 m/min, feed-…

A: GivenV=225m/minf=0.25mm/revd=7.5mmη=90% Cutting energy for Brinell hardess 175Hb=1.6J/mm3U=1.6J/mm3

Q: A 0.4-inch diameter bit is used in a vertical or vertical drill that operates at 300 rpm. If the…

Q: Identify and explain the method of milling process in which the stresses on the teeth is maximum at…

A: The milling process in which the stress on the teeth is maximum at the end of the cut is the up…

Q: A motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm…

Q: Exercises 4 1. A 30 mm diameter mild steel bar is being turned at a spindle speed of 8 rev/s, on a…

Q: In machining a mild steel work piece with carbide tool, the life of the tool was found to be 1 hour…

Q: 1- Define lath Process, why the tool should have Red Hardness Property? 2- What are the kinds of…

A: 1. The measurement of material hardness at a high temperature is referred to as "hot hardness…

Q: lease give the correct solution A cylinder of 25 mm diameter and 100 mm length is turned with a…

A: Given:Diameter, d=25,length, l=100 mVT0.25=55Vc=22 m/minf=0.046 mm/rev

Q: A drilling operation is to be performed with a 12.7 mm diameter twist drill in a steelwork part. The…

A: givendiameter of twist drill d=12.7mmdepth of hole h=60mmpoint angle 2α=118ocutting speed…

Q: 3. It is required to machine a slot with length 100 mm, width 15 mm, and depth 4 mm. Calculate the…

A: Given: The length of machine slot, L = 100 mm The width of machine slot, b = 15 mm The depth of…

Q: A job has to be machined in shaping and the process parameters are given below: Length of the…

A: Given that A job has to be machined in shaping and the process parameters are given below: Length…

Q: Orthogonal turning of a mild steel tube with a tool of rake angle 10° is carried out at a feed of…

A: Given: Rake angle = 10° Feed = 0.14 mm/rev The thickness of chip = 0.28 mm…

Q: A mild steel block is being drilled with a drill of 10 mm diameters. Given Helix angle = 30° Feed =…

Q: Aluminum bar with 100mm diameter and 500mm long is turned down to 88mm diameter, using two passes on…

Q: A slab-milling operation is being carried out on a block on a 200 mm-long, 150 mm-wide annealed mild…

Q: In machining a mild steel work piece with carbide tool, the life of the tool was found to be 1 hour…

Q: A mild steel block is being drilled with a drill of 10 mm diameters. Given Helix angle = 30° Feed =…

A: Drilling is the most common hole-making operation. It is usually performed with the help of a twist…

Q: f cut is 2 mm, what is the value of maximum uncut chip thickness when the table feed is 20 mm/min?

Q: The Orthogonal turning of a mild steel tube with a tool of rake angle 10° is carried out at a feed…

A: Given:The rake angle, α=10oFeed= uncut chip thickness, t1=0.14 mm/revThickness of the chip, t2=0.28…

Q: In a straight turning operations the diameter of a workpiece is reduced from 50 mm 40 mm using a…

A: Given:- diameter D0 = 50 mmFinal diameter D1 = 40 mmfeed rate F= 0.1 mm/revrake angle…

Q: Example 4.2.2: In a production turning operation, the foreman has decreed that a single pass must be…

A: Given data:

Q: A 400 mm long, 19.5 mm diameter of 304 stainless steel rod (assume specific energy of steel is 4…

Q: B/ In a drilling operation using a twist drill, the rotational frequency is 5 s', the feed rate is…

Question

1. A 7.5 -mm-diameter drill is used on a drill press operating at 300 rpm. If the feed is 0.125 mm/rev, what is the MRR? What is the MRR if the drill diameter is doubled?

2. Assume that the work piece material is high-strength aluminum alloy and the spindle is running at N = 500 rpm. Estimate the torque required for this operation.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Jigs and Fixtures and Their Applications

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 200 mm long magnesium alloy bar, 63 mm in diameter is turned on a lathe using a high speed steel cutter travelling at 180 mm/min. The spindle rotates at 450 rpm and lathe is equipped with a 10 kW motor, operating at a mechanical efficiency of 92%. The final diameter of the magnesium alloy bar is 59,5 mm. Indicate with a sketch the recommend size and location of the following tool angles: back rake, side rake, end relief, side relief and side and end cutting edge. Calculate the cutting time for the machining process.Calculate the required cutting force.
Please give the correct solution A cylinder of 25 mm diameter and 100 mm length is turned with a tool, for which the relation VT0.25 = 55 is applicable. The cutting velocity is 22 m/min. For a tool feed of 0.046 mm/rev, the number of tool regrinds required to produce 425 cylinders is?
A 78 mm thick plate is to be milled down to a thickness of 60 mm using an 80 mm face milling cutter. Calculate the processing time if the cutting depth is 6 mm, the feed/rev is 1.1 mm and the cutting speed is 15 m/min, and if the over run for a 620 mm long plate is 10 mm.
The Orthogonal turning of a mild steel tube with a tool of rake angle 10° is carried out at a feed of 0.14 mm/rev. If the thickness of the chip produced is 0.28 mm. Calculate the values, The shear angle.
Note: Read the question carefully and give me right solutions according to the question. In orthogonal cutting of steel tube of 150 mm diameter and 2 mm thick, the cutting force was 130 kg and feed force was 35 kg for chip thickness of 0.3mm. The orthogonal cut was taken at 60 meter per minute with a feed of 0.14 mm/rev. If the back rack angle of the cutting tool was - 8 o (minus 8 degree), then calculate the shear strain and strain energy per unit volume.
A motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm thickness at rate of 35 holes per minute. It requires a torque of 7 Nm for an area of hole in mm2. If the cutting takes 1/10 of a second and the speed of its flywheel varies from 165 rpm to 145 rpm, calculate:
Suppose in a face milling operation, the dimensions of the workpiece are 5 inches by 10 inches. The cutter is 6 inches in diameter, has 8 teeth, and rotates at 300 rpm. The depth of cut is 0.125 inches and the feedrate is 0.005 inches / tooth. Assume that the specific power requirement for this material is 2 hp min / in3 and that only 75% of the cutter diameter is involved in cutting. Calculate (a) the required power, and (b) the material removal rate.
Orthogonal turning of a mild steel tube with a tool of rake angle 10° is carried out at a feed of 0.14 mm/rev. If the thickness of the chip produced is 0.28 mm, Calculate the values of shear angle and shear strain.
A slab-milling operation is carried out on a 200 mm long, 80-mm-wide annealed mild-steel workpiece having a feedrate of 0.1 mm/tooth and a depth of cut of 4.0 mm. The cutter of 50 mm diameter has 18 straight teeth and rotates at 135 rpm. The given specific energy for this material is 3.5 W s/mm3 and the slab mill is wider than the workpiece to be machined. Calculate:‧ the material-removal rate;‧ the power and torque required for this operation;‧ the cutting time. (243 mm/min, 77760 mm3/min, 4.5 kW, 52.8 s)
A steel rod 250 mm long and 200 mm in diameter is being reduced to 190 mm in diameter all over its length in one travel. The machine spindle rotates at 500 rpm, whereas the tool is moving at an axial feed of 0.5 mm/rev; calculate the following: Material removal rate (mm3/min) Consumed gross power in Nm/s if cutting force is 477.5N and mechanical efficiency is 90% Cutting time plzz complete in 30 minutes
A drilling operation is to be performed with a 12.7 mm diameter twist drill in a steelwork part. The hole is a blind hole at a depth of 60 mm and the point angle is 118 ̊. The cutting speed is 25 m/min and the feed is 0.3 mm/rev. determine The cutting time to complete the drilling operation,
1. The shaft shown in the figure below is to be machined on a lathe from a Ø 25mm bar. Calculate the machining time if speed V is 60 m/min., turning feed is 0.2mm/rev, drilling feed is 0.08 mm/rev and knurling feed is 0.3 mm/rev?