A 400 mm long, 19.5 mm diameter of 304 stainless steel rod (assume specific energy of steel is 4 W.s/mm) is being reduced in diameter to 17 mm by turning on a lathe machine. The spindle rotates at N = 700 rpm, and the tool is traveling at an axial speed of 300 mm/min. Calculate: cutting speed material removal rate (i) (ii) (ii) (iv) (v) cutting time power dissipated cutting force

A 400 mm long, 19.5 mm diameter of 304 stainless steel rod (assume specific energy of steel is 4 W.s/mm) is being reduced in diameter to 17 mm by turning on a lathe machine. The spindle rotates at N = 700 rpm, and the tool is traveling at an axial speed of 300 mm/min. Calculate: cutting speed material removal rate (i) (ii) (ii) (iv) (v) cutting time power dissipated cutting force

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a turning operation, cutting speed =200 m/min; feed = 0.25mm mm/rev, and depth of cut = 4.00mm Thermal diffusivity of the work material = 20m mm^2/s and volumetric specific heat =3.5(10^ -3 )J/mm^ 3 -C If the temperature increase above ambient temperature (20degreesC) is the angle measured by a tool-chip thermocouple to be 700degreesC, determine the specific energy for the work material in this operation.
A student is using a lathe with 80-hp and 80% efficiency to fabricate a copper alloy with Sy = 1200ksi If the width of cut is 0.30 inand the student set a rake angle of 0and a cutting speed of 200fl / min while she assumed a coefficient of friction to be 0.5. What is the maximum depth of cut the student can achieve?
Note: Read the question carefully and give me right solutions according to the question. In orthogonal cutting of steel tube of 150 mm diameter and 2 mm thick, the cutting force was 130 kg and feed force was 35 kg for chip thickness of 0.3mm. The orthogonal cut was taken at 60 meter per minute with a feed of 0.14 mm/rev. If the back rack angle of the cutting tool was - 8 o (minus 8 degree), then calculate the shear strain and strain energy per unit volume.
a rod is to be manufactured using turning operations and is made of Nickel alloy. The rod is 80 mm in length and 15 mm in diameter. The final required diameter is 10 mm and the spindle rotates at N = 500 rpm while the tool axial speed is 100 mm/ min. Calculate material removal rate, cutting speed, cutting time, the power dissipated, and cutting force.
A flat milling operation will be carried out with a horizontal milling machine, in a piece of 250 mm in length and 50 mm in width, using a felicoidal bur with a diameter of 75 mm, with 10 teeth. If the feed per tooth is 0.2mm, and the cutting speed is 0.75 m / s, how would you determine the speed of metal removal to remove 6 mm from the surface of this piece?
A slab-milling operation is carried out on a 200 mm long, 80-mm-wide annealed mild-steel workpiece having a feedrate of 0.1 mm/tooth and a depth of cut of 4.0 mm. The cutter of 50 mm diameter has 18 straight teeth and rotates at 135 rpm. The given specific energy for this material is 3.5 W s/mm3 and the slab mill is wider than the workpiece to be machined. Calculate:‧ the material-removal rate;‧ the power and torque required for this operation;‧ the cutting time. (243 mm/min, 77760 mm3/min, 4.5 kW, 52.8 s)
An orthogonal cutting operation is being carried out under the following conditions: t0=0.38 mm, tc=0.65 mm, width of the cut= 2.5 mm, V=3.5 m/s, rake angle=6°, Fc= 515 N, and Ft=210 N. Calculate the percentage of the total energy that is dissipated in the shear plane.
What are the functions served by cutting fluid? Give broad classification of cutting fluid and explain each in detail .
Manufacturing Processes What is the effect of shear plane angle in metal cutting? Illustrate with diagram
2 1.46 Explain why the power requirements in cutting depend on the cutting force but not the thrust force.
A 78 mm thick plate is to be milled down to a thickness of 60 mm using an 80 mm face milling cutter. Calculate the processing time if the cutting depth is 6 mm, the feed/rev is 1.1 mm and the cutting speed is 15 m/min, and if the over run for a 620 mm long plate is 10 mm.
Draw the forces and angles involved in the cutting process and calculate shear angle (Ø), friction coefficient and tangential force ,cutting force = 80 kN, resultant of forces =100KN. friction force=75KN, rake angle =20' undeformed chip thickness = 0.65mm and deformed chip thickness = 0.72mm vjall