A 0.4-inch diameter bit is used in a vertical or vertical drill that operates at 300 rpm. If the feed is 0.005 in / rev, what is the MRR? What is the MRR if the drill diameter is doubled? What is the power required in the drill if the material is an annealed AISI 1080?

A 0.4-inch diameter bit is used in a vertical or vertical drill that operates at 300 rpm. If the feed is 0.005 in / rev, what is the MRR? What is the MRR if the drill diameter is doubled? What is the power required in the drill if the material is an annealed AISI 1080?

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter5: Turning

Section5.3: Machining Operations On The Lathe

Problem 5RQ: Calculate spindle RPM and machining time for cutting a 1.5" diameter 4" long at 225 SFPM using a...

See similar textbooks

Related questions

Q: A piece of Low carbon steel has (85mm) length machined by a lathe with cutting tool made of HSS,…

A: Given, Length of the specimen , L=85 mm. Depth of cut , d = 2 mm Feed , f = 0.2mm/rev. Cutting…

Q: During plain turning mild steel by a tool of geometry 0°, 0°, 7°, 8°, 12°, 90°, 0 (mm) at so= 0.35…

Q: A 4"x 8" cast steel plate is to be machined using a milling cutter with 8 inserts. The operation is…

A: Given dataD=8inchV=350sfpm=350×39.37=inch/minf=0.015inch/totthl3=0.18inchz=8 ***as per our company…

Q: 8. A hole of 20 mm diameter is to be drilled in a steel block of 40 mm thickness. The drilling is…

A: Solution:-Given thickness of steel block=40 mmapproach and over run together=d2=10 mmrotational…

Q: Sample Problem 1 A man create a 5 inches thick hole with a 2" diameter on an aluminum flat bar.…

Q: An Aluminium workpiece of 175 mm length is machined in a lathe, where the plain tuming openatinin…

A: Dear student, According to the guidelines I am allowed to answer only three…

Q: A hole is being drilled on a block aluminum alloy with 10mm drill at a feed of 0.25 mm/rev . The…

A: Given data:

Q: The time taken to drill a hole through a 30mm thick plate with the drill rotating at 200 rpm and…

Q: Through hole of 12 mm diameter is to be drilled in a steel plate of 20 mm thickness, drilled spindle…

A: Given: The diameter of hole is d=12 mm. The thickness of steel plate is t=20 mm. The drilled…

Q: Through hole of 12 mm diameter is to be drilled in a steel plate of 20 mm thickness, drilled spindle…

A: We know that linear velocity and rpm are related by : πDN = v ⇒N=vπD = 20π x 0.012 =530.5165 rpm

Q: 20 mm through hole is to be drilled in a 30 mm thick plate using a double fluted, 120° lip angle…

A: Given:hole diameter, d=20 mmthickness of plate, t=30 mmspeed of drill, N=500 rpmapproach=3…

Q: In a single pass drilling operation, a through hole of 15mm diameter is to be drilled in a steel…

A: Given: The diameter of hole, d = 15 mm The thickness of plate, h = 50 mm The spindle speed, N = 500…

Q: A 16mm Solid carbide tool with two teeth is used to machine Aluminium using the cutting speed of…

Q: A twin-spindle drill simultaneously drills one ½-in hole and one ¾" through a 1" wide work piece.…

Q: A 12" through hole is to be drilled in a 1 inch thick steel plate. A standard twist drill having a…

Q: Calculate the time required to machine a workpiece 170 mm long, 60 mm diameter to 165 mm long 50 mm…

A: Given:L1=170 mmL2=165 mmD1=60 mmD2=50 mmN=440 rpmf=0.3 mm/revd=2 mmApproach and overtravel=5 mm

Q: Sample Problem 3 How long will it take to mill a % inch by 2 long keyway in a 3 in diameter shafting…

Q: Example 2 Calculate the r/min at which a drill press should be set to make threading for M12 x 1.75…

A: Given- material - cast iron M12 x 1.75 Diameter of workpiece (D)= 12 mm Feed = Pitch of Thread =…

Q: A single-point HSS tool with a 3/64 in nose radius is used in a shaping operation on a ductile steel…

Q: Blind hole 20 mm diameter, 60 mm deep are being drilled in steel stock, drilling spindle speed is…

Q: 1. A 7.5 -mm-diameter drill is used on a drill press operating at 300 rpm. If the feed is 0.125…

A: Note - As per company guidelines we are allowed to answer only the first question, kindly post other…

Q: What is the function of a drill bushing? In cases where a drill bushing is not used, how is the jig…

Q: Q1\ a) The operation of drilling is to be done with a 25.4 mm ( diameter) twist drill in a brass…

Q: Explain the functions of drilling Stabilizers in drill string?

A: Drill string: It is a drilling ring column of the drill pipe which is used to transfer torque and…

Q: Aluminum bar with 100mm diameter and 500mm long is turnmed down to 88mm diameter, using two passes…

Q: n a drilling operation under, a given condition, the tool life found to decrease from 20 mint to 5…

A: Given:Tool life, T1=20 minutefinal tool life, T2=5 minutedrill speed, N1=200 rpmfinal drill speed,…

Q: A slab milling operation is performed to finish the top surface of a steel workpiece 250*75 mm*mm.…

Q: Calculate the RPM for drilling at 600 SFM and feed rate (in/min) for a chip load of .010 (in/rev)

Q: Through holes of 10 mm diameter are to be drilled in a steel plate of 20 mm thickness. Drill spindle…

A: Given:Diameter of holes, d=10 mmThickness of steel plate, t=20 mmspeed, N=300 rpmf=0.2 mm/rev

Q: A mild steel block is being drilled with a drill of 10 mm diameters. Given Helix angle = 30° Feed =…

Q: In a lathe machine, the maximum torque transmitted by a shaft exceeds the mean torque by 18 %. A…

A: Given, P=3 kW=3×103 WN=625 rpmTmax=1.18Tm

Q: A long workpiece, with the length-to-dimeter ratio that exceeds factor 10, is to be machined. Which…

Q: A shaft shown in Figure Q3 is to be machined using a lathe machine. The diameter of a raw block is…

A: Explanation: The stepwise procedure to solve this problem is shown in the following attached image:

Q: A mild steel block is being drilled with a drill of 10 mm diameters. Given Helix angle = 30° Feed =…

A: Drilling is the most common hole-making operation. It is usually performed with the help of a twist…

Q: A workpiece of 2000 mm length and 300 mm width was machined by a planning operation with the feed…

A: Given Data: Feed rate, f=0.3 mm/ stroke

Q: A milling cutter having 8 teeth is rotating at 150 rpm. If the feed per tooth is 0.1 mm, the speed…

A: Given:Milling cutter teeth,t=8 Speed, N=150 rpmfeed per tooth, ft=0.1 mm

Q: The Orthogonal turning of a mild steel tube with a tool of rake angle 10° is carried out at a feed…

A: Given:The rake angle, α=10oFeed= uncut chip thickness, t1=0.14 mm/revThickness of the chip, t2=0.28…

Q: (c) Refer to Figure 3(c) and assuming that D = 240 mm, w = 66 mm, I = 700 mm, d = 3.5 mm, v = 0.65…

Q: In turning of stales steel alloy, 1100 mm length and 400 mm diameter, the Feed was 0.35 mm/rev, and…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Jigs and Fixtures and Their Applications

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. A 7.5 -mm-diameter drill is used on a drill press operating at 300 rpm. If the feed is 0.125 mm/rev, what is the MRR? What is the MRR if the drill diameter is doubled? 2. Assume that the work piece material is high-strength aluminum alloy and the spindle is running at N = 500 rpm. Estimate the torque required for this operation.
Through holes of 10 mm diameter are to be drilled in a steel plate of 20 mm thickness. Drill spindle speed is 300 rpm, feed 0.2 mm/rev and drill point angle is 120° .Assuming drill overtravel of 2 mm. Calculate the time for producing a hole.
A o 20 mm through hole is to be drilled in a 30 mm thick plate using a double fluted, 120° lip angle drill The drill tip is at a distance of 3 mm from the plate surface when cutting is started and an over travel of 2 mm is recommended as a margin to ensure drilling through the full thickness of the plate. If the drill rotates at 500 rev/min and the feed per tooth is 0.01 mm,find the machining time of the operation.
Is a #6 twist drill larger than a #16 twist drill? What is the diameter of both twisting screws?
A drilling operation is to be performed with a 12.7 mm diameter twist drill in a steelwork part. The hole is a blind hole at a depth of 60 mm and the point angle is 118 ̊. The cutting speed is 25 m/min and the feed is 0.3 mm/rev. determine The cutting time to complete the drilling operation,
A drilling operation is to be carried out with a 12.7mm diameter twist drill in a steel work part.The hole is a blind hole of 50mm depth. The cutting speed is 25mm/min and the feed is 0.3mm/rev Determine the following i)Cutting time to complete the driling ii)Metal removal rate
A job has to be machined in shaping and the process parameters are given below: Length of the job=120 mm Speed of the motor=640 rpm Cutting speed=248 m/min Tool allowance before cutting =31.5 mm Tool allowance after cutting=10 mm Determine the cutting to return stroke ratio for the above operation and draw the arrangement of machining with tool head and allowances.
The cutting speed in in/min of a 12 mm drill operating at 600 rpm is nearly equal to
With a neat sketch explain the drill bit nomenclature?
Machining time required reduce a mild steel rod of diameter 60mm, initial length (L) 125mm to final length (L1) 120mm to 58 mm by turning a carbide insert. If the approach length and over run length are 5 mm and 1 mm respectively, take Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm
Explain how the size of an upright drill press is determined.
8 A job has to be machined in shaping and the process parameters are given below: a. Length of the job=120 mm b. Speed of the motor=640 rpm c. Cutting speed=264 m/min d. Tool allowance before cutting =30 mm e. Tool allowance after cutting=15mm Determine the cutting to return stroke ratio for the above operation and draw the arrangement of machining with tool head and allowances.