1. A d.c. shunt generator running at 850 r.p.m. gave the followig O.C.C. data : Field current (A) : 0.5 1 2 3 4 5 E.M.F. (V) : 10 60 120 199 232 248 258 If the resistance of the shunt field is 50 N, determine the additional resistance required in the shunt field circuit to give 240 V at a speed of 1000 r.p.m.

1. A d.c. shunt generator running at 850 r.p.m. gave the followig O.C.C. data : Field current (A) : 0.5 1 2 3 4 5 E.M.F. (V) : 10 60 120 199 232 248 258 If the resistance of the shunt field is 50 N, determine the additional resistance required in the shunt field circuit to give 240 V at a speed of 1000 r.p.m.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 220V shunt generator has an armature resistance of 0.02ohms and a shunt field resistance of 44ohms. at rate load, the driving engine develops 62.26hp. If the iron and friction losses amount to 1600W, how much is the current delivered to the load at this condition? (Our subject is ELECTRICAL MACHINE 1, and our lesson is Losses and Efficiency on the DC MACHINE) (I need a clean solution ma'am/sir. Thank you do much)
The armature and field resistances of a series machine are 0.2 ohm and 0.3 ohms respectively. While running as a generator, the generated emf is 250V at 1200rpm. If the machine is run as motor, it takes 4A at220V. At a certain load, the motor takes 30A at 220V. However, on load, the armature reaction weakens the field by 4%. Find the motor speed at this load.
A separately excited generator,when running at 1000rpm supplied 200A at 125V. What will be the load current when the speed drops to 800rpm if current is unchanged? Given the armature resistance of 0.04 ohms and brush drop of 2V.
The armature winding resistance of a long shunt connected DC generator is 0.4ohm, the resistances of the shunt and serial field windings are 125 ohms and 0.1 ohms, respectively. While the generator supplies 8KW of power to the load it feeds, which is the voltage it produces since the output voltage is 250V?
A 110-V shunt generator has a full load current of 100 A, shunt field resistance of 55 Ω and constant losses of 500 W. If F.L. efficiency is 88%, find armature resistance. Assuming voltage to be constant at 110 V, calculate the efficiency at half-F.L. and at 50% overload. Find the load current corresponding to maximum efficiency.
a dc shunt generator supplies a load of 10kW at 250V calculate the induced emf,if the armature resistance is o.5ohm and the shunt field resistance is 100ohm
A 110V shunt generator has a full load current of 100A, shunt field resistance of 55 ohms and constant losses of 500W. If full load efficiency is 88%, find the armature resistance. Assuming voltage to be constant at 110V, calculate the efficiency at half load. Find the load current.
A 110-V shunt generator has a full-load current of 100 A, shunt fieldresistance of 55 Ω and constant losses of 500 W. If F.L. efficiency is88%, find armature resistance. Assuming voltage to be constant at 110 V,calculate the efficiency at half F.L. And at 50% overload. Find the loadcurrent. Write the answer neatly.
The following test data are taken from 60kW, eight pole, 400 V, 50 Hz, class C, junction IM.DC Test: RDC = 0.152Ω Idle test:VNL = 400 , V f = 50 Hz , INL = 30 A ,PNL = 3400 W Locked-rotor TestVBR = 80 , Vf = 12.5 Hz IBR = 120 A ,PBR = 6500 W a) Find the velocities of the stator and rotor magnetic field? b) Find the value of smax and Tmax? c) Input current I1 and Input power Pin? d) Air gap power PAG and Rotor copper losses PRCL? e) Ind. Mek. Power Pconv and Output power Pout? f) Tconv the generated moment, Tout the spindle moment, and the efficiency of the motor ɳ? g) Find the value of smax and Tmax? h) Find the circuit parameters? i) Draw the per phase equivalent circuit of this motor?
A separately excited d.c. generator, when running at 1200 r.p.m. supplies 200 A at 125 V to a circuit of constant resistance. What will be the current when the speed is dropped to 1000 r.p.m. and the field current is reduced to 80%? Armature resistance, 0.04 ohm and total drop at brushes, 2 V. Ignore saturation and armature reaction
With increasing load current, the output voltage of a separately-excited DC generator falls, which is a property of its load characteristics (decreasing load resistance). As the load current grows, what is the most appropriate solution or action you can take to counteract this voltage drop and keep the output voltage at a consistent level? Note: Please explain in no more than 60 words.
A short-shunt compound DC generator supplies a current of 100 A at 220 V. If the resistance of the shunt field is 50 ohms, of the series field 0.025 ohms, of the armature 0.05 ohm, the total brush drop is 2 V and the iron and friction losses amount to 1 kW, determine the following: The armature current, Amp The generated voltage, V The copper losses, W The output power of the prime mover, kW The generator efficiency, %