1. A material is subjected to equal bi-axial tensile stresses of 60 MPa along the x- and y-axes. There is no additional stress. Determine the shear stress on the (1 1 1) plane toward the [10 -1] direction.

1. A material is subjected to equal bi-axial tensile stresses of 60 MPa along the x- and y-axes. There is no additional stress. Determine the shear stress on the (1 1 1) plane toward the [10 -1] direction.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.27P: -27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile...

See similar textbooks

Related questions

Q: A block is subjected to the stresses as shown in Fig. 1. If the allowable compressive normal stress…

Q: Determine stress produced by tensile force of 20 N applied on cross sectional area of 5 mm2

A: Given data: Tensile force (F) = 20 N Cross sectional area (A) = 5 mm2 Need to determine the stress…

Q: The state of stress of an element is given. Determine its principle plane by the specialized…

Q: The grains of wood in the board make an angle of 20° with the horizontal as shown. Using Mohr's…

A: Given that:P=280 Nb=25 mmd=60 mmθ=20ο

Q: In relation to Mohr's Circle which shows the relationship between normal and shear stress, at what…

A: we already know that the principal plane or maximum…

Q: Using analytical method of transformation equations; (a) The orientation of principal planes and the…

A: Given Data: The stress acting in the horizontal direction is, σx=2R MPa. The stress acting in the…

Q: The state of stress at a point in a member is shown on the element in Figure 6. Determine the stress…

A: Write the given information:

Q: a) The stress in the wire. Answer in MPa b) The strain in the wire. c) The increase in the length of…

Q: Part A Determine the shear strain at A relative to axes that are directed along AB and AD. Express…

A: Given, d1=0.38 ind2=0.5 in

Q: The state of plane stress at a point with respect to the xy-axes is shown in Fig. (a). Using Mohr's…

A: Calculated the principal stress and principal planes, maximum in-plane shear stress and calculated…

Q: The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and…

A: Given:- σx=70 MN/m2σy=50 MN/m2τxy=30MN/m2θ=30° To find:- The magnitude of the normal, tangential,…

Q: Determine the normal stress component acting on the plane AB. (Figure 1)

A: We have to find out the normal & shear component of force acting on the plane

Q: Determine the equivalent state of stress on an element at the same point which represents (a) the…

A: Givensig1=σy=-17MPasig2=σx=5MPash=τ=12MPa

Q: 4) The state of plane stress at a point is described by Or = Oy = o and Tæy =0. The stress on the…

A: given data σx = σy = σ, ζxy = 0 to determine stress on the plane inclines at 45 to x plane

Q: determine (a) the principal stresses and their principal planes, (b) the maximum shear stress and…

Q: Determine stress components acting on the inclined plane AB shown in Figure 1. The directions of the…

A: Given: The stress in x-direction, σx = -70 MPa The stress in y-direction, σy = 50 MPa The shear…

Q: An aluminum wire 3.0 m in length and 4.0 mm in diameter supports a 1000 N mass. Determine the…

A: Write the expression of the cross-sectional area of the wire.

Q: a) the principal stresses; and (b) the maximum in-plane shear stress.

Q: (a) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (b)…

Q: Determine stress components acting on the inclined plane AB shown in Figure 1. The directions of the…

A: Draw the figure .Given dataσx=-80 mpaσy= 60 mpa⟌xy=-30 mpaθ=40°

Q: The figure depicts the state of plane stress at a point. Sketch Mohr's circle for stress. Indicate…

Q: 1. The following state of strain has been determined on the surface of a cast-iron machine part: =-…

Q: Determine the absolute maximum shear stress of the stress state acting on the element shown in the…

A: It is required to determine absolute maximum shear stress

Q: 8.4 A material is subjected to two mutually perpendicular stresses, one 60 MN/m compressive and the…

Q: Determine the normal strain across line AB b.)Determine average shear strains at corners C and D…

Q: A block is subjected to the stresses as shown in Fig. 1. If the allowable compressive normal stress…

Q: The state of plane stress at a point is represented by the stress element below. Determine the…

Q: Determine the average normal stress at points A, B, and C. The diameter of each segment is indicated…

A: Given data: The diameter of the segment at A, dA = 0.5 in. The diameter of the segment at B, dB = 1…

Q: Determine (a) the principal stresses and (b) the maximum shear stress and associated normal stress…

A: normal stress in x direction σx=300 MPanormal stress in y direction σy=-100 MPa (-ve for…

Q: For the following structures, determine the maximum normal stress, deformation and displacement of…

Q: Q)The state of plane stress at a point is represented by the stress element below: A. Draw the…

A: Question (A) ,(B) & (C) is Solved here. For the other Parts, Please Post this Question again.

Q: a: What is the magnitude of the maximum shear stress in MPa? b: What is the magnitude of the…

A: Consider the tensile stresses to be positive and the compressive stresses to be negative. Write the…

Q: Determine the equivalent state of stress on an element at the same point which represents the…

A: find the normal stress on the element with orientation 31.7 °.

Q: Given the following plane element determine a. The principal stresses b. The principal angles (no…

Q: )The principal stresses.b)The principal directions (angles to the principal planes).c)The maximum…

A: Given:

Q: 8. Principal planes are those planes on which a. Normal stress is maximum b. Normal stress is…

A: Principal planes are the planes inside the material at which the shear stress is zero.

Q: 1. Determine the equivalent state of stress on an element at the point which represents, the…

A: The stepwise procedure to solve this problem is shown in the following attached image:

Q: Determine the normal and shear stresses at point D that act perpendicular and parallel,…

A: Given: The load at the point D is 10 kN. The beam is shown below:

Q: Two of the stress components in a 2-D plane stress system are found to be: = 5.0 MPa. бy It has also…

A: Given data: (a) Principal Plane: it is the plane that consists only of normal stress, the value of…

Q: On the free surface of an aluminum [E = 10500 ksi; v = 0.33] component, the strain rosette shown was…

Q: • When the state of stress is represented by the principal stresses, no shear stress will act on the…

A: When the state of stress is represented by the principal stresses, no shear stress will act on the…

Q: In 2D XY-plane-stress analysis, how many stress components you need to calculate. Please write/show…

Q: direction in which the normal stress is zero, direction in which the normal stress is zero, ulate…

Q: Determine stress components on an element oriented 60 ° counterclockwise with respect to the element…

A: Given stresses σx=100 MPaσy=160 MPaτxy=60 MPa

Question

1. A material is subjected to equal bi-axial tensile
stresses of 60 MPa along the x- and y-axes. There is no
additional stress. Determine the shear stress on the (1 1
1) plane toward the [1 0 -1] direction.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the \y axes, that is, determine crv, tr(_, and t, Show the results on a sketch of an clement oriented at B .
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
For the following structures, determine the maximum normal stress,deformation and displacement of point D relative to point A.
At a point in a material under stress there is a compressive stress of 200MN/m2 and a shear stress of 300MN/m2 acting on the same plane. Determine the principal stresses and directions of the planes on which they act
The state of stress at a point in a member is shown on the element. Suppose that σx = -50MPa , σy = -120MPa , τxy = -30 MPa . Determine the normal stress component acting on the plane AB. σx′=?
The state of stress at a point in a member is shown on the element. Suppose that σx = -50 MPa , σy = -120 MPaMPa , τxy = -30 MPa . Determine the shear stress component acting on the plane AB. Tx`y`=?
Given the stress cube below, represent the Mohr Circle, demonstrating the stepsfollowing:a) Calculation of main stresses and directions;b) Calculation of stresses in a plane of rotation ?, clockwise;c) Circle of Mohr.
The state of stress at a point can be described by σx = 40 MPa , σy = 64 MPa , and τxy = 18 MPa . A second coordinate system is rotated by θ = 25 ∘ A) What is the normal stress in the direction of the x′-axis? B) What is the shear stress in the y′-direction for the faces with a normal in the x′-direction? C) What is the normal stress in the direction of the y′-axis?
Suppose that σx = 42 MPa A) Determine the normal stress σx′ that acts on the element with orientation θ = -17.8 ∘. B) Determine the normal stress σy′ that acts on the element with orientation θ = -17.8 ∘. C) Determine the shear stress τx′y′ that acts on the element with orientation θ = -17.8 ∘.
A rectangular block has dimensions of 3 in, 4 in, and 5 in along the X-, y-, and z- axes, respectively. The block is subjected to triaxial loading of three uniformly distributed loadings of 30 kips (C), 45 kips (T), and 60 kips (C) along the x-, y-, and z- axes, respectively. If the strain along the X- axis and the z-axis are 0.00021 (C) and 0.00042 (T), respectively, determine the Poisson's ratio and the modulus of elasticity of the material. Also, what is the change in volume of the material?
When subjected to a compressive load, the length of the rod is 199,6 mm, and its diameter is 10 mm. If the original length was 200 mm, and modulus is 70 GPa, determine: 1.1 The stress and strain in the rod when loaded. 1.2 The magnitude of the load.
A body is subjected to a direct tensile stress of 300 MPa in one plane accompained by a simple shear stress of 200 MPa. Determine maximum normal stress on the plane.