P4 p 11:173GA1ZM.pdf >Q)The state of plane stress at a point is represented by the stress elementbelow:A. Draw the Mohr's Circle.B. Determine the principle stresses and draw the corresponding stresselements.C. Determine the maximum shear stress and draw the corresponding stresselement.D. Find the stresses on an element inclined at 30° clockwise and draw thecorresponding stress element.E. Provide a table illustrating the stress values as well as the inclinationangles and compare the obtained values from Mohr's Circle with thoseobtained from equations60 MPa50 MPa30 МРа...

Question (A) ,(B) & (C) is Solved here. For the other Parts, Please Post this Question again.

Q)The state of plane stress at a point is represented by the stress element below: A. Draw the Mohr's Circle. B. Determine the principle stresses and draw the corresponding stress elements. C. Determine the maximum shear stress and draw the corresponding stress element.

Q)The state of plane stress at a point is represented by the stress element below: A. Draw the Mohr's Circle. B. Determine the principle stresses and draw the corresponding stress elements. C. Determine the maximum shear stress and draw the corresponding stress element.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.18P: -18 through 7.4-25 An clement in plane stress is subjected to stresses ax,ay., and txy. (see...

See similar textbooks

Related questions

Q: QJThe state of plane stress at a point is represented by the stress element below: A. Draw the…

A: Given Data: σx=70 Mpaσy=65 Mpaτxy=35 Mpa

Q: A block is subjected to the stresses as shown in Fig. 1. If the allowable compressive normal stress…

Q: D. For a circular section the ratio of maximum shear stress to the average shear stress is

Q: 8.3 A rectangular block of material is subjected to a shear stress of 30 MN/m2 together with its…

Q: a. Use Mohr's Circle to determine the maximum shear stress on the element b. Also, using Mohr's…

A: Given:σx=50 MPaσy=-30 MPaζxy=20 MPa

Q: a: What is the magnitude of the first principal stress? b: What is the magnitude of the second…

A: Consider the tensile stresses to be positive and the compressive stresses to be negative. Write the…

Q: a) Prime planes, b) Prime stresses, c) Maximum shear stress and this in the plane of the stress

A: Given data: Normal streses along x and y axis σx=12000lb/in2 σy=18000lb/in2 Shear stress…

Q: The principal stresses at a point across two mutually perpendicular planes are 70 MN/m2 tension and…

A: Given:- σx=70 MN/m2σy=50 MN/m2τxy=30MN/m2θ=30° To find:- The magnitude of the normal, tangential,…

Q: Determine the shear stress (in Mpa) in the 28.36-mm-diameter pin at A that support the beam if P =…

A: P= 29.48 kN= 29480 N a= 2.86 m b= 5.57 m At A, the pin diameter, D= 28.36 mm To find: Shear stress…

Q: 1. This stress is developed when a force is applied perpendicular to the cross-sectional area of the…

A: Bearing stress differs from compressive stress in that it is induced by compressive pressures on…

Q: (a) Determine the magnitude of the maximum in-plane shear stress. (b) Determine the normal stress…

Q: 2. For the given state of stress, determine (a) the principal planes, (b) the principal stresses. 48…

Q: 1.42. Given the stress acting uniformly over the sides of a thin, flat plate (Fig. P1.42), determine…

A: Given Thin plate To find Stress at 20 to the horizontal Principal stress Orientation

Q: 1. Use the diagram below to answer the following questions a. Determine the normal stress exerted on…

Q: Required information Consider the given state of plane strain. Ex =-180µ, Ey=-260µ, Yxy= +295µ Use…

A: Since you have asked multiple questions, only the first question is solved for you. If you want any…

Q: 4) The state of plane stress at a point is described by Or = Oy = o and Tæy =0. The stress on the…

A: given data σx = σy = σ, ζxy = 0 to determine stress on the plane inclines at 45 to x plane

Q: Question 1: For the given state of stress, by using formula determine; Principal Plane - Principal…

Q: Q.1) For the state of stress shown below, use stress transformation equations to determine the…

Q: 1.66. The stresses (in megapascals) with respect to an x, y, z coordinate system are described by o,…

Q: A point on a thin plate is subjected to the two stress components o = 81 MPa and T = 130 MPa.…

Q: 1. The principal stress and orientation. Show the results on stress element.

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: For the state of plane stress shown in Fig. determine (a) the princi-pal planes, (b) the principal…

A: σx=50MPaσY=-10 MPaτxy=40 MPa (a) the principal planes…

Q: - The state of plane stress is represented by the stress element below. Draw the Mohr's circle,…

Q: Question 2 For the stresses of plane stress state is ox = -8 MPa , Oy = 7 MPa and Txy = -6 MPa Draw…

Q: Part B - Clockwise Rotation of a Stress Element with Only One Normal Stress The state of stress at a…

Q: A piece of material is subjected to two compressive stresses at right angles, their values being 40…

Q: Q-1) For the given state of stress, (a) draw Mohr's circle for this state of stress and show all…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: For the given state of stress, determine (a) the principal planes, (b) the principal stresses, (c)…

Q: A block is subjected to the stresses as shown in Fig. 1. If the allowable compressive normal stress…

Q: 3. For the given state of stress, determine the principal planes, the principal stresses, and…

Q: The state of plane stress at a point is represented by the stress element below. Determine the…

Q: Q2- Show the stress components of a point in plane stress on the square in Figures below: Orr = 27…

Q: QI/ For the state of plane stress shown below, construct a Mohr's circle and determine (a) the…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: a: What is the magnitude of the maximum shear stress in MPa? b: What is the magnitude of the…

A: Consider the tensile stresses to be positive and the compressive stresses to be negative. Write the…

Q: (b) An elemental cube is subjected to tensile stresses of 180 N/mm2 and 80 N/mm2 acting on two…

Q: [1] In simple stress, the axial force be. .to the subjected area. ......... O A. Perpendicular O B.…

A: Ans.3 When the bar subjected to direct stress the region in which the bar returns to its original…

Q: )The principal stresses.b)The principal directions (angles to the principal planes).c)The maximum…

A: Given:

Q: 4) Mohr's circle is shown for a point in a physical object that is subjected to plane stress. If 1…

Q: The normal and shear stresses acting on one plane passing through a point in a soil mass are 120 psi…

A: Among the applied normal stresses on mutually perpendicular planes the stress corresponding to…

Q: The stress at a point is shown on the element. Determine (a) principal stress, (b) maximum in-plane…

A: (a) To find: The principle stress. Given: The stress in x-direction is σx=-85 MPa. The stress in…

Q: One of the principal stresses in a two-dimensional stress system is 139 N/mm² acting on a plane A.…

Q: A force of 400N is applied on a area of 20m ^2 . Determine the stress generated by the force .

A: The problem is based on mechanics and can be solved as:

Q: A figure shows a state of stress; determine the shearing stresses and normal stresses after the…

Q: Q 1: A plane element is subject to the stresses. Determine analytically (a) the principal stresses…

Q: (5.2) What is the maximum shear stress in the medium if the principal stresses are given by o, and…

A: Given principal stresses are σ1 and σ2 (NOTE: According to Bartleby's Answering Guidelines, only…

Q: Plane stress at a point in a body is defined by the principal stresses, 9 ở and o. On the plane of…

Q: (a) The plane stress at a point with respect to x-y-axes is shown in Fig. Q1(a). By using…

A: according to the given details:

Q: Mohr's Circle The major and minor principal stresses acting at a point are 80 psi compression and 20…

A: A) To Draw : The Mohr's circle for this stress combination. Given: The major principal stress…

Q: A point on a thin plate is subjected to the two successive states of stress shown. Determine the…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

P4 p 11:17
3G
A1ZM.pdf >
Q)The state of plane stress at a point is represented by the stress element
below:
A. Draw the Mohr's Circle.
B. Determine the principle stresses and draw the corresponding stress
elements.
C. Determine the maximum shear stress and draw the corresponding stress
element.
D. Find the stresses on an element inclined at 30° clockwise and draw the
corresponding stress element.
E. Provide a table illustrating the stress values as well as the inclination
angles and compare the obtained values from Mohr's Circle with those
obtained from equations
60 MPa
50 MPa
30 МРа
...

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Note

VIEW

Step 2: Given Data

VIEW

Step 3: (A) Drawing The Mohr's Circle

VIEW

Step 4: (B) Calculate The principle Stresses

VIEW

Step 5: (C) Calculate The Maximum Principle Stress

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
At a point on the web of a girder on an overhead bridge crane in a manufacturing facility, the stresses arc known to be x = —4300 psi, a = 1700 psi, and r = 3100 psi (the sign convention for these stresses is shown in Fig, 7-1). A stress clement located at the same point in the structure (but oriented at a counterclockwise angle 0, with respect to the _y axis) is subjected to the stresses shown in the figure {b, r», and 2100 psi). Assuming that the angle 8Xis between zero and 90°, calculate the normal stress trA, the shear stress ta, and the angle Bv
-18 through 7.3-22 An element in plane stress (see figure) is subjected to stresses o, a., and (a) Determine the principal stresses and show them on a sketch of a properly oriented element. (b) Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element. 7.3-18 a=2I50kPa, ay=375kPa.Txy.=-460kPa
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
-18 through 7.4-25 An clement in plane stress is subjected to stresses ax,ay., and txy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements. 7.4-18 sx= 2900 kPa, sy= 9100 kPar,txy=-3750kPa
For the stresses of plane stress state is ?? = −8 ??? , ?? = 7 ??? and??? = −6 ???Draw a Mohr’s circle diagram.Draw stress element for the given stressesFind the principal normal and shear stresses, and determine the anglefrom the x axis to ?1Draw the stress element for the principle stress.Using stress transformation, find the principle stresses and the angle of ?1Determine the stress transformation for the angle ∅ = 25° #Answer all in detail
Using Mohr's circle on each case, determine a)The principal stresses and maximun shear stress. Show all results on sketches of properly oriented elements b)Is there the invariance of normal stresses in each case?
A hollow bronze shaft with anoutside diameter of 80 mm and a wallthickness of 5 mm is subjected to a torqueof T = 620 N·m and an axial load of P =9,500 N, as shown in Figure P15.3/4.(a) Determine the principal stresses andthe maximum shear stress at point Hon the surface of the shaft.(b) Show the stresses of part (a) and theirdirections on an appropriate sketch.
Considering the original state of stress as shown in figure below and recalling the already developed equations for normal and shear stress at an angle Ɵ c.c.w from x-axis, mathematically prove that the planes of maximum in-plane shear stress are inclined at 45o to the principal planes.