Show complete solutions, graph and table if needed. 1. A soil deposit is shown in the figure below. The ground water table, initially at the ground surface, waslowered to a depth 25ft below the ground. After such lowering, the degree of saturation of the sand abovewater table was lowered to 20%.Water tableGround surfaceYsat = 135 pcfYa = 116 pcf%3DSand50 ft25 ftClay Ysat = 120 pcfa) What is the vertical effective pressure at the midheight of the clay layer before lowering of the watertable, in psf.b) What is the vertical effective pressure at the midheight of the clay layer after lowering of the watertable, in psf.c) What is the vertical effective pressure when there is no water in the sand layer, in psf.

1. A soil deposit is shown in the figure below. The ground water table, initially at the ground surface, was lowered to a depth 25ft below the ground. After such lowering, the degree of saturation of the sand above water table was lowered to 20%. Water table Ground surface Ysat = 135 pcf Ya = 116 pcf Sand

1. A soil deposit is shown in the figure below. The ground water table, initially at the ground surface, was lowered to a depth 25ft below the ground. After such lowering, the degree of saturation of the sand above water table was lowered to 20%. Water table Ground surface Ysat = 135 pcf Ya = 116 pcf Sand

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter9: Consolidation

Section: Chapter Questions

Problem 9.8P

See similar textbooks

Similar questions

Question 32 A dense silt layer has the following properties: void ratio = 0.66, specific gravity = 2.5. Free ground water is 9.47 m. below the ground. Capillary action rise will reach 6.66 meters. The soil above capilary action rise is dry while within the zone, it is saturated at 52.77%. Determine the effective pressure (in kPa) at a depth of 7.42 meters from the ground surface. Round off to three decimal places.
The sand layer shown is 2.5m thick. Beneath the sand layer is a 1.8m thick clay layer, underneath the clay layer is a solid rock. Water table is at depth of 0.9 m below the ground surface. SAND: Ymoist= 23KN/m3 ; Ysat= 21KN/m3 CLAY: Ysat= 23 KN/m3 ; LL= 42% e=0.7 A.) Compute the overburden pressure at mid-clay layer. B.) Find the maximum surface pressure without exceeding a 139.5mm settlement in clay layer if it is assumed to be normally consolidated. C.) If surface pressure is 70kpa and pre-consolidation pressure is 80kpa, find the settlement in clay layer.
The soil profile at a site consists of 5 m sand underlain by clay layer. The ground water table is 2 m below the ground surface. Average void ratio of sand is 0.52. Water content of clay is 42% and degree of saturation of sand above water table is 37%.Assume specific gravity of sand and clay is 2.65. 1. Compute the unit weight of clay. a. 19.82 kN/m³ b. 17.47 kN/m³ c. 18.62 kN/m³ d. 16.20 kN/m³ 2. Compute the total pressure 10 m below the ground surface. a. 185.41 kPa b. 160.25 kPa c. 140.53 kPa d. 153.62 kPa 3. Compute the effective pressure 10 m below the ground surface. a. 106.94 kPa b. 96.52 kPa c. 115.62 kPa d. 108.36 kPa
A uniform soil deposit has a void ratio 0.6 and specific gravity of 2.65. The natural ground water is at 2.5 m below natural ground level. Due to capillary moisture, the average degree of saturation above ground water table is 50%. Determine effective pressure in kPa at a depth of 6 m. a. 46.40 b. 323.9 c. 80.66 d. 117.9
A dense silt layer has the following properties: void ratio = 0.7, specific gravity = 2.58. Free ground water is 10.58 m. below the ground. Capillary action rise will reach 7.46 meters. The soil above capilary action rise is dry while within the zone, it is saturated at 54.74 %. Determine the effective pressure (in kPa) at a depth of 7.5 meters from the ground surface.
A dense silt layer has the following properties: void ratio = 0.75, specific gravity = 2.59. Free ground water is 9.49 m. below the ground. Capillary action rise will reach 6.69 meters. The soil above capilary action rise is dry while within the zone, it is saturated at 50.02%. Determine the effective pressure (in kPa) at a depth of 7.51 meters from the ground surface. Round off to three decimal places. Selected Answer: 128.657
Plz give the correct answer. Compute the intensities of active and passive earth pressure at depth of 8 m in dry cohesionless sand with an angle of internal friction of 30 degrees , and unit weight of 18kN / (m ^ 3) What will be the intensities of active and passive pressure if the water level rises to the level? Take the saturated unit weight of sand as 22kN / (m ^ 3) .
A dense silt has the following properties: void ratio = 0.64, specific gravity = 2.5. Free ground water = 10.23m below the ground. Capillary action rise will reach 5.6m. The soil above the capillary action rise is dry while within the zone, it is saturated at 51.53%. Determine the effective pressure (in kPa) at a depth of 7.42m from the ground surface.
A dense silt layer has the following properties.void ratio = 0.30eff. Diameter ?10 = 10??capillary constant (c)=0.20 cm²Groundwater level is 8.0m below the ground surface 1. Calculate the height of capillary rise in the silt. 2. Calculate the vertical effective stress in kpa at 5m depth, assume ?? = 26.5 ??/?³and that the soil above the capillary action rise and ground surface is partially saturated at 50%. 3. Calculate the effective vertical stress at 10m depth assuming ?? = 26.5 ??/?³and that the soil above the capillary action rise and ground surface is partially saturated at 50%.
Estimate the lateral earth pressure at a depth 20 ft (6.1 m) below the ground surface in a loose sand deposit. The wet unit weight of the sand is 115 pcf (19 kN/m3). What would the total lateral pressure be if the water table rose to the ground surface (in psf or kPa)?
A dense silt layer has the following properties: Void ratio = 0.76, SG= 2.59. Free ground water is 9.31m below the ground. Capillary action rise will reach 7.93m. The soil above capillary action rise is dry while within the zone, it is saturated at 53.13%. Determine the effective pressure (kPa) at a depth of 7.05m from the groind surface. Use stored value. Asnwer in 5 decimal places.
A clay layer 12ft thick rests beneath a deposit of submerged sand 26ft thick. The top of the sand is located 10ft below the surface of a lake. The saturated unit weight of the sand is 125 lb /ft³ and of the clay layer is 117 lb /ft³. 1. Compute the total vertical pressure at the mid height of the clay layer. a. 4390psf b. 4577 psf c. 4963psf d. 4800psf 2. Compute the pore water pressure at the mid height of the clay a. 2659psf b.2620 psf c. 2668 psf d. 2680psf 3. Compute the effective vertical pressure at the mid height of the clay a. 1731psf b.1956 psf c. 2295psf d. 1273psf