-1. A steel pipe line with a nominal diameter of 36 in has an ID of 34.50 in (899 mm) and a wall thickness of 0.75 in (19 mm). The line is 500 ft (152.5 m) long and is embedded at each end in a rigid concrete structure. The temperature of the line may vary from -20 to +120°F. What is the maximum thrust which can be developed by temperature changes? What stress does this produce in the pipe?

-1. A steel pipe line with a nominal diameter of 36 in has an ID of 34.50 in (899 mm) and a wall thickness of 0.75 in (19 mm). The line is 500 ft (152.5 m) long and is embedded at each end in a rigid concrete structure. The temperature of the line may vary from -20 to +120°F. What is the maximum thrust which can be developed by temperature changes? What stress does this produce in the pipe?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.36P

See similar textbooks

Similar questions

Two pipes 1 and 2 having the following properties are connected in series: Pipe 1 - Length = 1500m, Diameter = 850mm f= 0.025 Pipe 2 - Length = 1200m, Diameter = 650mm f= 0.020 It is required to replace these two pipes with a single pipe whose length is 2700m. Assuming that the friction factor for the new pipe is 0.015, what is the required pipe diameter?
It is a torsional parameter equal to twice the product of the area enclosed by the centerline of the tube and the shear flow. a. Torsional stress b. Torque c. Angle of Twist d. Modulus of rigidity
A geothermal well produces from total depth at 1000m and produces dry (saturated) steam with a temperature of 200°C. Shut-in wellhead pressure is 5000kPa, and the wellhead flowing pressure is 1000kPa when the well is flowing 100 tons/hour. Determine the downhole pressure and temperature in each case ( for shut-in case and the flowing case). Assume: Casing diameter =0.2m a Casing roughness =0.0005m Please answer fast i give you upvote.
A steel pipe having a diameter of 15 cm and a wall thickness of 9.50 mm has an allowable stress of 140,000 kPa. What is the maximum allowable internal pressure in the pipe?
Determine the smallest metric hydraulic copper tube size that will carry 4L/min of thefollowing fluids while maintaining laminar flow: (a) water at 40°C, (b) gasoline(SG=0.68) 25°C, (c) ethyl alcohol (SG=0.79) at 0°C, and (d) heavy fuel oil at 25°C. answer correctly the last part only please thank you
The sketch for the warm water heating system of a studio apartment is shown in the figure. The volumetric flow rate of water through the piping system with a diameter of 0.0162 m is 0.000162 m3/s. the pipes used in the system are made of galvanized pipes (roughness value ε = 0.015mm). The minor loss coefficients for each fitting are for the elbow piece (KL=2,62), the heater corner valve(KL=5,62), the radiator(KL=3,62), the gate valve(KL=1,62) and the boiler (KL=4,62). Assuming that the density of water is1000 kg/m3, determine the power required to derive the circulation pump, which has an efficiency of 76,2 percent. Solve the problem by making the necessary assumptions and drawing the schematic figure. (a=6 and b=2 on the figure)
A pump, for which the characteristic curve is shown below, is used to pump water from a canal into a dam. The pump is mounted 2.0 m above the water level. There is a 50 mm PVC pipe connected to the suction side of the pump, and a 40 mm PVC pipe connected to the discharge side. The total length of pipe on the suction side is 8 m, and there is a strainer (K = 20), a non-return valve, a 90° elbow and a fully open gate ball valve in the suction line. Another fully open gate valve, and two 90° elbows are mounted in the discharge line. The total length of the discharge line is 60 m, and the discharge pipe outlet is 4 m above the pump. You may assume a water temperature of 25 °C. Determine: (a) The flow rate through the system(b) The required fluid power(c) The efficiency of the pump(d) Whether the pump will cavitate or not.
Fundamental Problem
A compressor piston has a stroke of 380 mm and the clearance volume of 7% of thestroke volume. At the beginning of compression stroke the pressure of air is 0.99 barWhen the piston has travelled 260 m from the begining of the compression stroke thedelivery valves open and delivers air at 4 bar. Find the value of "n", iif the compressionfollows the law PVn = CA. 1.37B. 1.39C. 1.28D. 126
A water pump is used to pump water from one large reservoir to another large reservoir that is at a higher elevation. The free surfaces of both reservoirs are exposed to atmospheric pressure, as sketched in Fig. The dimensions and minor loss coefficients are provided in the figure. The pump’s performance is approximated by the expression Havailable = H0 − aV.2 , where the shutoff head H0 = 125 ft of water column, coefficient a = 2.50 ft/(gpm)2 , available pump head Havailable is in units of feet of water column, and capacity V. is in units of gallons per minute (gpm). Estimate the capacity delivered by the pump
An induced draft fan handles 63,500 cfm in of flue gas with a gas constant of 51.5116 ft-lb / lb-R from a boiler at 500 degrees Fahrenheit against a static pressure of 4in. water. The discharge duct diameter is 73.67in. The barometric pressure is 29.9” Hg. Determine the following: a. the total head in ft. of water b. the Air Power in horsepower
In an annular section made of commercial steel pipe with an outer diameter or 13.78 inches inside a commercial steel pipe with an inner diameter of 23.62 inches carries a water flowrate of 600L/sec. The total length of the section is 10m. What is the frictional loss in meters of water at a temperature of 68o F?