1. Arack and pinion system is one way to convert a rotational motion into a linear motion or vice-versa. Here, the pinion gear A with radius 0.3 ft rolls on the gear racks C and B shown. Rack B moves to the right at 6 f/s, while rack C moves to the left at 2 ft/s. Find the angular velocity of the gear and the velocity of its center A. 03 ft

1. Arack and pinion system is one way to convert a rotational motion into a linear motion or vice-versa. Here, the pinion gear A with radius 0.3 ft rolls on the gear racks C and B shown. Rack B moves to the right at 6 f/s, while rack C moves to the left at 2 ft/s. Find the angular velocity of the gear and the velocity of its center A. 03 ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylinder rolls without slipping between two moving plates C and D. The radius of the cylinder is r=4.0m. The velocity of the plate C is VC=6.0 m/s to the right. The velocity of the plate D is VD=2.0 m/s to the left. Using the instantaneous center of zero velocity (IC) to determine (3) The magnitude of the angular velocity of the cylinder ω=____________rad/s
A wheel and a connected pulley are rotating around a fixed shaft "O" and driven by a belt. At a specific moment, the velocity of point "A" on the belt is 0.6 m/s, and its acceleration is 2 m/s², both in the directions shown in the diagram. Calculate the magnitude of the total acceleration of point "B" on the wheel at this moment.
(Three-Dimensional Motion) The figure below represents a pair of bevel gears A and B. Gear A rotates in ahorizontal plane about a vertical axis at O. Gear B rotates around the shaft OC,which in turn rotates about the terminal axis at O. At the instant shown, theangular velocity of the shaft OC is 10j rad/sec, and gear A is stationary. Deter-mine the angular velocity of gear B, and the velocity of a point D at the top ofgear B.
Dynamics Lesson For the electric saw shown in the figure, the saw can slide left and right on the horizontal bed where it is placed. Since the engine rotates the crank counterclockwise with a constant angular velocity of 60 dv/min, find the acceleration of the saw and the angular acceleration of the arm AB for the position where ?=90o
In the system given in the figure, the piece consisting of m1 and m2 masses rotates counterclockwise with an angular speed of 5 rad / s. It is known that m1 = 300 gr and m2 = 170 gr.The angle made by the mass m1 with the X axis is 100degree, while the angle made by the m2 mass with the X axis is 45degree.And The distances of the m1 and m2 masses to the center of rotation are given as 0.5 m and 0.3 m, respectively. a)Find the centrifugal force of the masses m1 and m2 separately in N.? b)Find the total centrifugal force on the part?
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Arm AB has a clockwise angular velocity ωAB while the ring gear R has a counterclockwise angular velocity ωR. Using the Instantaneous Center (IC) Method, determine (a) the angular velocity (in rad/s) of gear B and (b) the velocity (in cm/s) of gear tooth D at the instant shown. Also, (c) illustrate the location of each rigid body’s instantaneous center. Utilize the following given:s = 13.5 cmrB = 6 cmωAB = 0.55 rad/sωR = 0.16 rad/s
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Arm AB has a clockwise angular velocity ωAB while the ring gear R has a counterclockwise angular velocity ωR. Using the Instantaneous Center (IC) Method, determine (a) the angular velocity (in rad/s) of gear B and (b) the velocity (in cm/s) of gear tooth D at the instant shown. Also, (c) illustrate the location of each rigid body’s instantaneous center. Utilize the following given:s = 13.5 cmrB = 6 cmωAB = 0.55 rad/sωR = 0.16 rad/s *for part (c), please follow the proper way of illustrating Instantaneous Centers (IC) on the next picture. Here's the youtube link of the attached picture where the proper illustration of IC was also discussed https://www.youtube.com/watch?v=1aQ9EZGMdDk
Collars A and B are attached by a rod of length 30 cm, as shown below. The joint at A is a ball-and-socket and at B a pin joint. Collar A moves in the z direction, while the guide bar for collar B is on xy plane. At the instant shown, collar A is at a height of 24 cm and collar B is moving with a speed of 3 m/s towards the x axis. Find the (a) angular velocity of the rod, and (b) the sliding of collar B. Use the image attached to solve the question
Find: angular velocity of gear B (omega B) when t = 2 seconds. and Displacement of gear B (teta B) when t = 2 seconds.
(Three-Dimensional Motion) The figure below represents a pair of bevel gears A and B. Gear A rotates in ahorizontal plane about a vertical axis at O. Gear B rotates around the shaft OC which in turn rotates about the terminal axis at O. determine the angular accelera tion of gear B when gear A is stationary and member OC has an angular velocity of 10j rad/sec and and angular acceleration of 25j rad/sec2 .
At the instant shown in Figure P6, the slider block, C, is moving at a constant speed of 700 mm/s to the right. If h1=30mm ,h2=20 mm ,d1=40 mm, d2=120 mm, determine the angular velocities of arms AB and BC.
The figure is made of rigid members AB, BC, DE, and EF, whichare pinned at A, B, D, E, and F. End C of member BC is pinned to a block which slides on member DE. For the given position, angular velocity of member AB = 2 rad per sec clockwise and angular acceleration of member AB = 3 rad / s^2 counterclockwise. Find the linear velocity and acceleration of the block at C for this position.