Figure 1 shows a double cursor C formed by two sliding pieces hinged on the bar AB and the circular path shown. Calculate the velocity and acceleration of point C at the instant when the angle is equal to 45 degrees, knowing that the angular velocity is equal to zero. Make the free-body diagram. 0,4m Fagura 4

Figure 1 shows a double cursor C formed by two sliding pieces hinged on the bar AB and the circular path shown. Calculate the velocity and acceleration of point C at the instant when the angle is equal to 45 degrees, knowing that the angular velocity is equal to zero. Make the free-body diagram. 0,4m Fagura 4

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure is made of rigid members AB, BC, DE, and EF, whichare pinned at A, B, D, E, and F. End C of member BC is pinned to a block which slides on member DE. For the given position, angular velocity of member AB = 2 rad per sec clockwise and angular acceleration of member AB = 3 rad / s^2 counterclockwise. Find the linear velocity and acceleration of the block at C for this position.
(a) What is the tangential acceleration of a bug on the rim of a 9.0 in. diameter disk if the disk moves from rest to an angular speed of 76 revs/min in 5.0 s? (b) When the disk is at its final speed, what is the tangential velocity of the bug?
A system of machines shown has a motor which has a radius of 1 inch that begins rotating at w=41 (1-e^-t) rad/s, where t is in seconds. The smooth pulley 4 inches in radius and the blades (16 inches radius) has the same center of rotation and mass. Assuming no frictional force is developed throughout the system, calculate the normal acceleration of point P in inches/seconds^2 at time t=0.5sec.
At the image below, what is the rotation of rod AB about point A if piston b moves to the right? Moreover, what is the magnitude of the acceleration of end a if velocity of end A is 7.5 m/s upward and is increasing at a constate rate of 18.75 m/s^2?
A circular body rotates according to the equation (S = 2 t4 – 4), Find the radius of the body to give an angular acceleration of (3 t2 rad / sec2
In the mechanism shown in the figure, the C pin attached to the element no. can slide. Calculate the angular velocity and angular acceleration of slide number 3. Elements 2 and 3 Calculate the accelerations of the centers of gravity. θ.2 rad/s=18 θ..2 rad/s 2 = 33 r2 = 900mm d2 = 530mm s3 = 430mm d4 = 330mm
The relative acceleration of point A with respect to point B of the disk in Figure 1 is given asaA/B = 3.347i + 1.283j. If the disk rolls without slipping, determine the angular velocity andangular acceleration of the disk at the instant. If, in other case, the disk rolls with slipping andthe vM = 2 m/s to the left and vO = 2 m/s to the right, do you think that the process ofdetermining its angular velocity and angular acceleration becomes easier or harder?
In the given figure, A link OB is rotating with a constant angular velocity of 2 rad/s in counter clockwise direction and there is a block is sliding radially outward on it with an uniform velocity of 0.75 m/s with respect to the rod, If OA = 1m , find the magnitude of the absolute acceleration of the block at location A ?
(Three-Dimensional Motion) The figure below represents a pair of bevel gears A and B. Gear A rotates in ahorizontal plane about a vertical axis at O. Gear B rotates around the shaft OC which in turn rotates about the terminal axis at O. determine the angular accelera tion of gear B when gear A is stationary and member OC has an angular velocity of 10j rad/sec and and angular acceleration of 25j rad/sec2 .
The crank of a slider crank mechanism rotates clockwise at a constant speed of 300 r.p.m. The crank is 150 mm and the connecting rod is 600 mm long. Using vector diagrams, Determine: a). Linear velocity and acceleration of the midpoint of the connecting rod. b). Angular velocity and angular acceleration of the connecting rod, at a crank angle of 45 from inner dead centre position. c). Using trigonometry, confirm your results for the velocity and acceleration in parts (a) and (b).
At the position shown in the figure, the velocity of the slidingcollar is ?? = 3m/s and its increasing at the rate of 1.4m/s2.a) Find the angular velocities of link AB and BC by usinginstantaneous center of zero velocity methodology.b) Find the angular accelerations of AB and BC.
In the figure shown, the pivoted right link AB carries a pin P whose position is controlled by horizontal slotted bar. At the instant that y=2in, the slotted bar is moving upward at a constant velocity of 4 ips. What is then the x-components of the velocity and acceleration of the pin P?