1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm

Q: A 10 cm long sample of some material elongates 0.2 mm when heated from 25°C to 200°C. Calculate the ...

A:

Q: A 36 cm x 36 cm , horizontal double acting air compressor w/ 5% clearance operates at 120 RPM and dr...

A:

Q: Required intormationH In a certain medical application, water at room temperature and pressure flows...

A:

Q: Determine the force in each member at joint A, B and C of the truss and indicate whether the members...

A:

Q: A simple saturated refrigeration cycle for R-12 system operates at an evaporating temperature of -5°...

A: Given that: The working fluid is R12. For the refrigeration cycle, evaporator temperature = -5 oC. C...

Q: Figure 2 shows the loads supported by a steel rod (E = 200 GPa) with a diameter of 30 mm Neglecting ...

A:

Q: A horseshoe player releases the horseshoe at A with an initial speed vo = 38 ft/sec. Determine the r...

A:

Q: Consider the surface of a pipe to be smooth with air flowing through it. The air flow rate (flowing ...

A: An isothermal process is characterized by the equation- P1v1=P2v2 where, P1 is the pressure of the a...

Q: Describe line of influence?

A:    The greatest BM will be right beneath the unit load, which is at a distance of x from the left su...

Q: Determine the force, in kN, due to water acting on one side of the parabolic gate. Round your answer...

A: Answer: The force due to water acting on one side of the parabolic gate is 141.26 kN.  

Q: An engine that operates on an Otto cycle has the details as shown in Table 2 below. Table 2 No. of c...

A:

Q: What is Pascal's principle

A:    The importance of pressure in fluids is due to Pascal's principle, which is an empirically establ...

Q: A trimetallic bar is uniformly compressedby an axial force P = 9 kips applied through a rigidend pla...

A:

Q: Three towers (labelled as points T1, T2, and T3) detected an invading fighter jet moving in an arc (...

A:                   Take scale, 1cm=100km so that,1 to 2, 2.6cm=260km.            ( 2 to 3), 4,4cm=440...

Q: In traveling a distance of 3.5 km between points A and D, a car is driven at 87 km/h from A to B for...

A: Acc is found for B to C and separate distances are calculated, added and equated to 3.5 km.

Q: A homogenous ladder 10m long and weighing 35 kg leans against a vertical wall. The angle between it ...

A:

Q: Determine the dewpoint of the

A: Given :- Dry bulb temp =28 Relative Humidity=50 To Find:- Dew point temperature=?

Q: Flow through the converging nozzle in Fig. P4.2 can be approximated by the one-dimensional velocity ...

A:

Q: A rigid vessel of volume 0.86 m° contains 1 kg of steam at a pressure of 2 bar. Evaluate the specifi...

A: The properties of steam shift incredibly with the strain and temperature changes. For exact estimati...

Q: A pump impeller rotating at 1400 rpm has an outside radius of 21 cm, the vane outlet angle β2 is 158...

A: given: N=1400 rpm Ro=21 cm=.21 m β2=1580 Cr2=4 m/s Assume the constant radial flow Cr1=Cr2=4 m/s  

Q: What are the indices for the directions indicated by the two vectors in the sketch below 0,4 nm Dire...

A:

Q: A 3.8 kg block is attached to a vertical spring with spring constant 18 N/m. At one instant, the blo...

A: Mass, M = 3.8 kg Spring constant, K = 18 N/m At y = 5.4 cm , V = 30 m/s It is asked to find the ampl...

Q: What effect does the end shape of the tungsten have on its own welding performance?

A:

Q: A test on centrifugal pump operating at 3237 rpm showed a total head of 39 ft at a capacity of 900 g...

A:

Q: In the figure, block 1 of mass m, slides from rest along a frictionless ramp from height h = 3.1 man...

A:

Q: A rigid vessel of volume 0.86 m° contains 1 kg of steam at a pressure of 2 bar. Evaluate the specifi...

A: Answer: (a) Specific volume is 0.86 m3/kg. (b) Temperature is 120.21 ℃. (c) Dryness fraction is 0.97...

Q: A diver is 21m below the free surface of the sea. The barometric pressure is 101.000 kPa and SG is e...

A: Answer: The pressure exerted on the diver at this depth is 45.185 psi.  

Q: The motor B draws in the cable at a speed of v, = 5r² m's where t is in seconds, as shown. Determine...

A:

Q: A torque T is applied to a thin-walled tubehaving a cross section in the shape of a regular hexagonw...

A: Given   b = Length of side    t = Thickness Find Shear stress τ  Rate of twist

Q: 10) A bar of 1018 steel is passed through rollers to reduce its area and increase its length. The in...

A:

Q: Q) solve exersice The response of a system is given by x() = 0.003 cos (302) + 0.004 sin(30) m Deter...

A:

Q: The acceleration of a particle is given by a = 3t - 34, where a is in meters per second squared and ...

A:

Q: A single CNC code block may contain only one G command. OTrue O False

A: Answer: The given statement is True.  

Q: Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 17...

A:

Q: A 2-stage centrifugal pump delivers 50 gpm of 225oF water against 200 ft head at 3200 rpm. a) What i...

A:

Q: 6 m 6 m 4 m A

A:

Q: derive shear and moment equations

A:

Q: Cylinder 8 is moving downwards at 4 fl's and the speed is decreasing at 2 fus?. Determine the in sec...

A:

Q: 1 100 kg 3. 2.

A:

Q: Required information According to potential theory for the flow approaching a rounded two-dimensiona...

A: Given: The speed, U = 17 m/s The constant, a = 11 cm The density of fluid, ρ = 917 kg/m^3 The viscos...

Q: 25 30 35 40 45 50 |12. 10° (R-h) х103 х103 х103 х103 х103 х103 Larson-Miller 100,000 |2.2- 10° (K-Һ)

A: stress=80MPa(11600psi)Temperaure=700°C(973k) To-Find:- Time to rupture =.................hours

Q: Compare Celebrity to other cruise lines in terms of sustainability.

A:   The cruise industry has the potential to make a substantial contribution to the UN's Sustainable D...

Q: A Pelton turbine having 1.6 m bucket diameter develops a power of 3600 kW at 400 rpm under a net hea...

A:

Q: 4) The thin flat bar is axially loaded with tensile orce P 45 kN and the yield stress in the bar is ...

A:

Q: In traveling a distance of 3.5 km between points A and D, a car is driven at 87 km/h from A to B for...

A:

Q: A water tank in the figure shown is made from steel plates that are 1/2 in. thick. Find the height t...

A:

Q: Interpret the following codes and decide where is the position of the tool in the Y direction at the...

A:

Q: Why is argon the most commonly used shielding gas for GTA welding?

A: Argon is the used as a shielding gas for GTA welding because as we know argon is an inert gas and ab...

Q: A hollow shaft has to be designed for a marine engine delivering 1200 kW when running at 120 r/min. ...

A:

Q: The displacement of a particle is given by s = 3t3 - 40t2 + 94t - 47 where s is in feet and t is in ...

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.