Three towers (labelled as points T1, T2, and T3) detected an invading fighter jet moving in an arc (path). The fighter jet’s flight information is as follows: Tower

Q: Two blocks of wood 50mm wide and 20mm thick are glued together. a. Using the free body diagram conce...

A: Calculated shear load and from it the shearing stress in the glued joint and also deriving shear str...

Q: A hollow steel [E= 30,000 ksi] tube (1) with an outside diameter of 2.75 in. and a wall thickness of...

A:

Q: What theory was used to get the values of acceleration? please explain

A: Relation between acceleration of blocks.

Q: Tower 1 - 300 km 15° EastofNorth @ 2:50 AM; Tower 2 - 250 km North @ 2:30 AM; and Tower 3 - 283 km...

A: From the given condition: we can locate the position of the jet as shown below. From tower 3, the je...

Q: Question 1. For the beam shown, there is a pinned support on the left and a roller support on the ri...

A: The free-body diagram of the beam is given below, On taking moment about 1, V20.65+0.35+1-9001+0.65...

Q: A jet of water 50 mm diameter is discharging under a constant head of 70 meters. Find the force exer...

A: Diameter of jet, d=50 mm=0.05 m H=70 m, Coefficient of velocity, Cv=0.9

Q: also for t seconds. If the brakes are applied for 3.7 seconds between B and C to give the cara unifo...

A:

Q: Find the velocity values ​​for different values ​​of l(Theta) from the equation below and draw the g...

A: Given: the equation of the velocity→v=rωsinθ+sin2θ2n length of the connecting rod→l=150 mm=0.15 m ra...

Q: Using the right-handed rule for a typical vertical 3-axis CNC machine, which direction is the right-...

A: Using the right handed rule for a 3 axis CNC machine, right hand thumb points at positive X (X+) dir...

Q: A 1000 MW steam power plant, which is cooled by a river, has a thermal efficiency of 50 percent. Det...

A:

Q: Determine the reactions a

A:

Q: R lock Page 7 of 8 Problem 6 14.0 kN 1.5 kN/m bam -1.0 m-1.0 m→* 2.0 m- For the beam shown above loo...

A:

Q: If a particle moves in such a way that a = 2t - 1 m/s/s, where t is in seconds. Determine the partic...

A: Answer: 29.2 m

Q: 39. A Norman window consists of a square surmounted at the top by a semicircle. If its area is 26.28...

A: Answer: The length of the vertical side is 4.34 ft. Therefore, the correct answer is option (A).  

Q: 1.) Derive the shear and moment equations 200 N 1000 N/m 60 N.m 0.2 0.2 0.6m 0.2 m

A:

Q: Determine the Miller Indices of Direction C and D in an HCP crystal.

A:

Q: The basketball player likes to release his foul shots with an initial speed vo = 25.1 ft/sec. What 2...

A:

Q: In the process of charging the accumulator piston (diameter D=120 mm and mass m=0,6 kg) moved upward...

A:

Q: Define how resonance occurs in a dynamic system? What must you take into account from preventing thi...

A: given; Define how resonance occurs in a dynamic system? What must you take into account from prevent...

Q: The winch on the truck is used to hoist the garbage bin onto the bed of the truck. If the loaded bin...

A:

Q: 90 kN 70 kN (1) (2) A B C 90 kN 0.85 m 1.15 m

A: GIVEN DATA- A1=2720mm2 E1=28GPa A2=21560mm2 E2=16.5GPa

Q: A tensile testing machine operates using two lead screws. Both lead screws have a square thread prof...

A:

Q: An ammonia compressor operates at an evaporator pressure of 316 kPa and a condenser pressure of 1514...

A: Evaporator pressure=316kPaCondenser pressure=1514.2kPASubcooled at 5°Superheated at 8°'Stroke Ratio=...

Q: Located the centroid of the plane area shown unit in mm 120 40 40 30 20 kat 50 20 20 30

A:

Q: In traveling a distance of 2.6 km between points A and D, a car is driven at 115 km/h from A to B fo...

A:

Q: Problem 1: A plastic component was subjected to a series of step changes in stress as follows: 1) An...

A: according to the question

Q: Describe how Foilsim calculates lift and drag.

A:

Q: 3. Based from the pump performance curve below, calculate the following: a) Specific speed b) Suctio...

A: Given data pump performance curve  Specific speed and Suction Specific speed is to be calculated.

Q: 1. A deaerator heater supplies 150 L/min of deaerated feedwater into a booster pump at 115 oC pumpin...

A: the density of deaerated water is 1056kg/ m^3 Pressure height is given by H= P/pg H= 100×1000/(1056×...

Q: A plant located at an altitude of 925 m has an open feedwater heater located  2.76 m above the pump...

A: The pressure head at any point in the fluid system can be calculated using the formula given below a...

Q: A Pelton turbine having 1.6 m bucket diameter develops a power of 3600 kW at 400 rpm under a net hea...

A: We know that a pelton turbine with a 1.6 m bucket diameter produces 3600 kW at 400 rpm under a net h...

Q: A hollow steel shaft ACB of outside diameter50 mm and inside diameter 40 mm is held againstrotation ...

A: Given data as per question Outside diameter of the shaft=50 mInside diameter of the shaft=40 mmLet h...

Q: Figure 2 shows the loads supported by a steel rod (E = 200 GPa) with a diameter of 30 mm Neglecting ...

A:

Q: The following figure shows the critical position of a crane that supports 2.5 Tons of load by means ...

A: (a) Start by calculating the rest of the forces in the crane using equilibrium equations: ∑Fx=0-4.2+...

Q: The diameter of the discharge pipe of a boiler feed pump is 4 inches and the suction pipe is 6 inch...

A:

Q: Lead has FCC crystal structure. If the atomic weight of Pb is 207.2 g/mol and density of 11.36 g/cm^...

A: It is required to determine atomic radius of Pb

Q: Give three examples of materials processes that rely on diffusion in solids and explain how diffusio...

A: Three examples of material process that rely on diffusion are 1. Case hardening 2. Doping 3.Nitridin...

Q: On turning a corner, a motorist rushing at finds child on the road 50 m ahead. He instantly stops th...

A: The velocity of the car is defined distance covered by the car in unit time. i.e.if the distance cov...

Q: or a particle of mass m moving under the force of F = a(xī + y] + 2zk). Here a is a onstant. ) Is th...

A:

Q: The displacement of a particle is given by s = 3t - 50t² + 91t - 53 where s is in feet and t is in s...

A:

Q: For the system KNO3-NaNO3-H2O, a ternary point exists at 5°C at which the two anhydrous salts are in...

A: according to the given question Ternary point : Phase = 3 ; C =3 , F = 0 (invariant point). All the ...

Q: pitot tube directed into a waler stream having Velociy .3 m/sec. Its gauge difference of 30 cm on th...

A:

Q: A Proell governor has equal arms of length 320 mm. The upper and lower ends of the arms are pivoted ...

A:

Q: design a simple mass-spring-damper, indicate the values of the system, and provide an equation where...

A:

Q: 4. What is the length of the longest part?

A: To find Length of longest part.

Q: Why must tungsten be hot in oder to have a stable arc

A: The tungsten must be hot in order to have a stable arc welding Because as we know that, the electron...

Q: A jet is deflected by an angle of 90 degrees, as shown below. Before the impact on the blade (solid-...

A:

Q: Caleulate the force F required to Keep the paraboli gate in static equilibrium shown in the Fiqure. ...

A: given; a=8.8mb=4.8mwidth(w)=2mspecific gravity (SG)=8.4

Q: A particle moves along a straight line with a velocity in millimeters per second given by v = 490 - ...

A: Answers: (a) ∆s = 1.528589 m. (b) D = 1.789255 m.  

Q: A Pelton turbine having 1.6 m bucket diameter develops a power of 3600 kW at 400 rpm under a net hea...

A:

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.