1.) Calculate the volume of a water cylinder with a total height of 10 meters and whose diameter is 400 centimeters, whose top section is a semi-sphere? 2.) calculate the volume of a cylinder where: a.) the area of the base is 30cm^2 and the height is 6cm. b.) the radius of the base is 14cm and the height is 10cm.

1.) Calculate the volume of a water cylinder with a total height of 10 meters and whose diameter is 400 centimeters, whose top section is a semi-sphere? 2.) calculate the volume of a cylinder where: a.) the area of the base is 30cm^2 and the height is 6cm. b.) the radius of the base is 14cm and the height is 10cm.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter6: Fundamental Dimensions And Units

Section: Chapter Questions

Problem 49P

See similar textbooks

Similar questions

The figure shows gate AB, 4 meters high, submerged in water. It is inclined 40 degrees with respect to the horizontal. Using the figure shown, determine the distance of CG (center of gravity) to CP (center of pressure) in meters.
Consider a fully filled tank of semi-circular cross section tank with radius R and width of b into the page, as shown. If the water is pumped out of the tank at flow rate of V· = Kh2, where K is a positive constant and h is the water depth at time t. Determine the time needed to drop the water level to a specified h value of ho in terms of R, K, and ho.
A cross-section of a tank with a width 5 m (into the page) is filled with water. A quarter cylindrical structure in one wall protrudes into the tank as shown in the Figure. The distances AB, and BC are 4 m and 1 m respectively. i)Calculate the size and centre of pressure of the vertical hydrostatic force on the surface BC. ii)Calculate the size and centre of pressure of the vertical hydrostatic force on the surface CD.
A rectangular tank that is 5/6 full, has a length of 26cm, height of 20cm and width of 15cm. If the water is transferred to another tank that is 18cm by 9cm by 30cm, how much water will overflow? (1cm^3 =1mL)
Consider a hydraulic jack being used in a car repair shop, as in the figure. The pistons have an area of Ap= 0,8 cm? and A= 0.04 m2, Hydraulic oil with a specific gravity of 0.870 is pumped in as the small piston on the left side is pushed up and down, slowly raising the larger piston on the right side. A car that weighs 13,000 N is to be jacked up. At the beginning, when both pistons are at the same elevation (h= 0), calculate the force F+ in newtons required to hold the weight of the car. 1. What height of mercury column will cause a pressure of 680 kPa? Use sg of mercury equals to 13.6 2. Determine the pressure in a vessel of mercury, specific gravity 13.6, at a point 20 cm below the surface. Express the answer in kN/m2.
3. A vertical piston-cylinder device on the left containing a gas has a mass of 40 kg and a cross-sectional area of 0.012 m². The local atmospheric pressure is 95 kPa, and the gravitational acceleration is 9.81 m/s². Determine the absolute pressure (kPa) inside the cylinder. (2 decimal)
Given the acceleration-time diagram sketch the velocity-time diagram and determine the displacement at time=9s.
The water tank has a diameter of 750mm , a height of 1750mm to which the Initial height of water was 5 cm. If water was to be filled 90% of height and the water meter initial reading is 2000L, a. what is the final reading of the water in L b. Find the mass of water tank if its initial weight is 45 kg
A tank is in the shape of an inverted cone, having height h = 2.5 m and base radius r = 0.75 m. If water is poured into the tank at a rate of 15 L/s, how long will it take to fill the tank? Water flows into a cubical tank at a rate of 15 L/s. If the top surface of the water in the tank is rising by 1.5 cm every second, what is the length of each side of the tank?
calculate the value of the force exerted by the water above the window of the dam. Be sure to explain why if the pressure varies from the surface of the water, the lower limit for the integral is taken from depth "a" and not from zero? (it is convenient that you make diagrams to support your answer).
In figure 6, compute the pressure difference between m and n, in pounds per square inch, when: (a) Fluid A is brine (sp gr 1.15), the gage fluid is oil (sp gr 0.92), and z = 45.15 in. (b) Fluid A is water, the gage fluid is air, and z = 15.15 in.
The figure shows a system where water flows from a tank through a system of pipes of different sizes and elevations. If we assume that there is no energy loss in the system, find: a. The volumetric flow through the pipe in ft3/sb. The pressure at point Bc. The pressure at point Cd. The flow velocity at point F in ft/s