1. Determine the noise spectral density of a 100 k2, 200 k2, 300 k2 that are in series and at a temperature of 25C. A data acquisition system has a 40 KHz bandwidth and a very high input impedance compared with the resistor value. Find the overall RMS voltage. k is Boltzmann's constant (1.38X10-23 J/K).

1. Determine the noise spectral density of a 100 k2, 200 k2, 300 k2 that are in series and at a temperature of 25C. A data acquisition system has a 40 KHz bandwidth and a very high input impedance compared with the resistor value. Find the overall RMS voltage. k is Boltzmann's constant (1.38X10-23 J/K).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2. Prove that , for a radio receiverOutput SNR in dB = Input SNR (dB) - Noise Figure(NF)[You can start the derivation from the relation connecting Noise Figure (NF)and Noise Ratio(F) ] note: the answe will be by hand written.
An Armstrong modulator is used to generate FM which is suitable for FM broadcasting.You are given input of narrowband FM signal with carrier frequency fc1 = 27 MHz anda frequency deviation Δf1= 17 kHz. Assume that the frequency multiplier with n = 3 andlocal oscillator frequency of 80 MHz. Calculate the output of the carrier frequency andfrequency deviation if additive frequency is selected by mixer. Explain your obtainedanswer.
For the frequency modulated signal given below, find (a) instantaneous frequency (b) deviation ratio, (c) frequencydeviation, and (d) transmission bandwidth by using Carson’s rule.
help please with explain A narrowband FM signal has a carrier frequency of 110 kHz and a deviation ratio of 0.05. The modulation bandwidth (signal bandwidth) is 10 kHz. This signal is used to generate a wideband FM signal with a deviation ratio of 18 and a carrier frequency of 98 MHz. a) Give the required value of frequency multiplication, n. b) Give two frequencies for the mixer to give the desired carrier. c) Define the required bandpass filter (center frequency and bandwidth).
A 10KHz sinusoid is used to frequency modulate a 50-KHz carrier signal and amplitude 10volt, the peak frequency deviation from carrier is 200KHz. The FM signal is applied to a non-Linear system whose input –output transfer characteristic is e (t) = 2e2(t). The output is filtered with an ideal bandpass filter having a oi bandwidth of 20KHz, centered at 100KHz.Sketch to scale the resulting line spectrum, Find the modulation index and find total power.
Q 2 :J An audio signal given by 15sin(4000pi * t) + 20sin(8000pi * t) amplitude modulated(DSB-FC) a sinusoidal carrier wave 60sin(100, 000pi * t) a. Derive an expression for the modulated signal. b. Find the modulation index. c. Find the spectrum of the modulated signal. d. Sketch the spectrum of the modulated signal e. Which type of demodulation method you propose to reconstruct the audio at receiver. Why? to
A 1500 KHz carrier with amplitude of 50 V is amplitude modulated by 2 –KHz sine wave tone with a peak voltage of 15 V. Determine the modulation index, percent modulation, the upper and lower sideband frequencies, bandwidth of the wave, and write the AM equation.
An FM radio broadcast used a modulator with a frequency deviation sensitivity of 5KHz/V, a 2Vp – 10 kHz modulating signal, and a 10Vp – 88MHz carrier Signal , determine : (a) Actual minimum bandwidth from the Bessel function table in kHz (b) Appropriate minimum bandwidth using Carson’s rule in kHz (c) Percent Modulation (d) The FM modulated waveform carrier and significant sideband components amplitudes; NOTE: Use this format in providing your answers to this problem: VJ0=x.xx v,VJ1=x.xx v,VJn=x.xx v; where VJO is the modulated carrier amplitude, VJ1-VJn is the amplitudes in significant sideband components and the number of sidebands (n) depending on your computation. (e) The unmodulated carrier power (W) for the FM modulator assumes that the load resistance is 50 Ω f) The corresponding FM modulated waveform carrier and significant sideband components power and its total power in mW. Note: Use this format in providing your answers to this problem: PJ0=xxx.xx mW,PJ1=xxx.xx…
Draw frequency response curve of a bandpass filter whose end frequencies are 0.1 MHz and 0.4 MHz respectively. Consider peak amplitude as 1. Use your own scale and necessary values.
By a suitable graphical representation sketch signal voltage (V) against period (t) of an FM System at t ranges from 1sec to 12sec. Taken magnitude of signal voltage to be 10V, 2pifc = 10*108, 2pifm = 3000, carrier deviation is 2.337KHz. please step by step solution. You are required to show work
The circuit show in figure has fr=200MHz, Cbc=1pf, Cbe=50pf, 1rbb=0 and rbe=1kohm. Derive an expression for Av=Vo/Vs at high frequency and find the value of effective fH
Answer the Following and provide solution. 1. The maximum frequency deviation of the carrier is ± 15 kHz and the maximum modulating frequency is 3 kHz, calculate for the modulation index. 2. Assume that the 60-dB bandwidth of a receiver is 12 kHz and the 6-dB bandwidth is 7 kHz. What is the shape factor of the circuit? 3. What is the bandwidth of a receiver with a quality factor of 50 and a resonance frequency of 540 kHz. 4. What is the maximum bandwidth of an FM signal with a deviation of 27 kHz and a maximum modulating signal of 4 kHz as determined by Carson’s rule? 5. A PM signal has a maximum allowed deviation of 17 kHz and an actual deviation of 8 kHz. What is the percentage modulation?