1. Determine the second mass moments I, , 3d - 3d I, and J, for the plate shown. The plate has uniform thickness, t, normal to the plane of the figure, and uniform mass den- sity, p. The parameters d, p, t and are given. 6d 4d Radius = 2d

1. Determine the second mass moments I, , 3d - 3d I, and J, for the plate shown. The plate has uniform thickness, t, normal to the plane of the figure, and uniform mass den- sity, p. The parameters d, p, t and are given. 6d 4d Radius = 2d

Name: 1. Determine the second mass moments I,,3d-3d -I, and J,for the plate
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 1. Determine the second mass moments I,,3d-3d -I, and J,for the plate shown. The platehas uniform thickness, t, normal to theplane of the figure, and uniform mass den-sity, p. The parameters d, e, t and are given.6d4dRadius = 2d

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.118P: A concrete seawater dam is shown in cross section. Is the dam safe against tipping about edge A? The...

See similar textbooks

Similar questions

The plane region A is submerged in a ï¬‚uid of weight density . The resultant force of the ï¬‚uid pressure on the region is R acting at the point C (called the pressure center) located at the distance h below the surface of the ï¬‚uid. Show that R=Qa and h=Ia/Qa, where Qa and Ia are the first and second moments of A about the axis a-a.
Air in the accompanying piston-cylinder device is in equilibrium at 190 oC.The mass of the hanging weight is 13kg.Atmospheric pressure is 100 kPA,and the piston diameter is 10cm.Determine the pressure of air inside.Assume g=9.81 m/s2.
Complete solution with free body diagram.
A loaded scow has draft of 1.6 m in sea water (sg = 1.03) when in upright position. The scow is 6 m wide and 12 m long and 2.4 m high. The center of gravity of the scow is 1.8 m above the bottom along the vertical axis of symmetry. Assume that the center of buoyancy is located half of the height of draft. a. Determine the initial metacentric height, considering upright position. b. What is the maximum single weight in kN that can be moved transversely from the center of the unloaded scow over the top edge without sinking the scow? (Considering rolling position) c. Determine the metacentric height due to pitching if the scow is tilted until one end is just submerged in seawater.
I need to draw a free body diagram and the solution M kg=406
A cylinder has a conical cavity and is topped by a hemispherical cylinder, such as as indicated in the figure. a) Locate the centroid of the composite volume if R = 200 mm and h = 250 mm. b) Locate the center of mass of the composite volume if the cylinder is made of brass (ρ = 8750 kg / mᶟ) and the finish is made of aluminum (ρ = 2770 kg / mᶟ)
For what uniform rotation rate in r/min about axis C willthe U-tube in Fig. take the confi guration shown? Thefl uid is mercury at 20 ° C.
The figure at right shows a child’s toy. This toy takes the form of a cylinder mounted on top of a hemisphere, of total mass M. The radius of the hemisphere is R, and the CM of the toy is a height h above the floor when the toy is vertical. Assume that the cylinder and the hemisphere have the same density. In terms of R, what is the maximumthickness d of the cylinder for which the toy will remain stable?
In celebration of the end of term, see the symmetric wine glass of 300 g mass, as shown below.Note that the wine is frozen because you left the glass outside. What is the maximum force magnitude P that can be applied to the glass before movement occurs? What kind of movement will occur? What kind of movement will occur if the base is changed to be 120 mm wide, themass of the glass increases to become 400 g, and μs = 0.2?
Answer with complete solution and a Free Body Diagram.
A tall open-topped standpipe has an inside diameter of 2,750 mm and a wall thickness of 6 mm. The standpipe contains water, which has a mass density of 1,000 kg/m3 . (a) What height h of water will produce a circumferential stress of 16 MPa in the wall of the standpipe? (b) What is the longitudinal stress in the wall of the standpipe due to the water pressure?
A spherical neutrophil 16µm in diameter is resting as shown in the attached photo. The pressure difference between the inside and outside of the cell is 7.5Pa. a) Draw free body diagrams of the whole cell and one hemisphere of the cell. b) Calculate cortical tension in the cell. In a micropipette aspiration experiment, a suction pressure of 52.5 Pa was used to aspirate the neutrophil membrane. c) Draw free body diagrams of the whole cell under micropipette aspiration and the portion of the cell in the micropipette. What is the diameter of the micropipette tip used to make this hemispherical projection? Next, the micropipette aspiration was stopped, and the cell was treated with Cytochalasin D, an inhibitor of actin polymerization, causing the cortical tension to decrease by half. d) Assuming the pressures inside and outside the cell have not changed, what is the new cell radius? e) If the same micropipette was used to aspirate the cell, what would be the new suction pressure?