A solid circular steel rod 5 mm in diameter and 500 mm long is rigidly fastened to the end of a square brass bar 25 mm on a side and 400 mm long, the geometric axes of the bars lying along the same line. An axial tensile force of 5 kN is applied at each of the extreme ends. Determine (a) the deformation of the steel rod in mm. (b) the deformation of the brass bar in mm. (c) total elongation of the assembly. For steel, E= 200 GPa, and for brass, E= 90 GPa.

A solid circular steel rod 5 mm in diameter and 500 mm long is rigidly fastened to the end of a square brass bar 25 mm on a side and 400 mm long, the geometric axes of the bars lying along the same line. An axial tensile force of 5 kN is applied at each of the extreme ends. Determine (a) the deformation of the steel rod in mm. (b) the deformation of the brass bar in mm. (c) total elongation of the assembly. For steel, E= 200 GPa, and for brass, E= 90 GPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A composite shaft shown, composed of a steel (G = 77 GPa) core inside an aluminum (G = 25 GPa) jacket, carries a torque, T = 10 kN-m. The shaft is designed such that the aluminum jacket will fail first upon the application of the torque. 1) If the allowable shear strength of aluminum is 45 MPa, determine the minimum thickness, t, of the aluminum jacket, that can carry the torque.2) What must be the minimum shear strength of steel such that the aluminum jacket will fail first?3) Determine the maximum angle of twist that can be applied to the shaft.
It is intended to manufacture a circular bar to resist torque; however, the bar is made elliptical in the process of manufacturing, with one dimension smaller than the other by a factor k as shown. Determine the factor by which the maximum shear stress is increased.
Question 1For the steel truss (E= 200 GPa) and loading shown in the figure, determine the deformations of members AB and AD, knowing that their cross-sectional areas are 2400 mm2 and 1800 mm2, respectively.
A standard tension test is used to determine the properties of anexperimental plastic. The test specimen is a 15 mm diameter rod and it issubjected to a 3.2 kN tensile force. Knowing that an elongation of 11 mmand a decrease of diameter of 0.625 mm are observed in a 120 mm gagelength, determine the modulus of elasticity, the modulus of rigidity, andPossion’s ratio of the material.
The rigid bar ABD is connected to the rod BD which consists of a single bar with a width of 25,0 mm and a thickness of 13 mm. Knowing that each pin has a diameter of 10 mm determine the value of the maximum average normal stress on rod BD considering the angle θ=90°. Calculate the deformation in the BD rod knowing that it is made of steel with an elastic modulus equal to 210GPa. Knowing that pins A, B and D are made of steel with a limit stress of 180Mpa, calculate the smallest allowable diameter so that they support the load applied to them considering an overall safety factor of 2,8.
The rod ABC is made of aluminum for which E = 70 GPa. Force P = 42 kN and Q = 6 kN. Rod AB is 20 mm in diameter and 0.40 m long while Rod BC is 60 mm in diameter and 0.50 m long. Determine the deformation in mm of (a) rod AB and (b) rod ABC.
(a) A 25 mm diameter bar is subjected to an axial tensile load of 100KN. Under the action of this load a 200 mm gauge length is found to extend 0.19 x 10-mm. Determine the modulus of elasticity for the bar material. (b) If, in order to reduce weight whilst keeping the external diameter constant, the bar is bored axially to produce a cylinder of uniform thickness, what is the maximum diameter of bore possible given that the maximum allowable stress is 240 MN/mo? The load can be assumed to remain constant at 100kN. (c) What will be the change in the outside diameter of the bar under the limiting stress quoted in (b)? (E = 210 GN/m2 and 1 = 0.3).
A standard tension test is used to determine the properties of an experi-mental plastic. The test specimen is a 58-in.-diameter rod and it is subjected to an 800-lb tensile force. Knowing that an elongation of 0.45 in. and a decrease in diameter of 0.025 in. are observed in a 5-in. gage length, determine the modulus of elasticity, the modulus of rigidity, and Poisson’s ratio for the material
A rectangular aluminum block is 100 mm long in the x direction, 75 mm wide in the y direction and 50 mm thick in the z direction. It is subjected to a triaxial loading consisting of a uniformly distributed tensile forces of 200 kN in the x direction and uniformly distributed compressive forces of 160 kN in the y direction and 220 kN in the z direction. If n = 1/3 and E = 70 GPa, determine the resultant deformation in the x, y and z direction. Determine also a single distributed loading in the x direction that would produce the same z deformation as the original loading.
The ABD rigid bar is connected to the BD rush which consists of a single bar with a width of 25.0 mm and a thickness of 13 mm. Knowing that each pin has a diameter of 10 mm determine the value of the maximum average normal stress on rod BD considering the angle θ= 90°. Calculate the deformation in the BD rod knowing that it is made of steel with an elastic modulus equal to 210 GPa. Knowing that pins A, B and D are made of steel with a limit stress of 180 Mpa, calculate the smallest allowable diameter so that they support the load applied to them considering an overall safety factor of 2.8.
A rectangular piece of wood, 50mm by 100mm in cross section, is used as a compression block shown. Determine the axial force P that can be safely applied to the block if the compressive stress in wood is limited to 25 MPa and the shearing stress parallel to the grain is limited to 10 MPa. The grain makes an angle of 20° with the horizontal, as shown.
A steel pipe of 400-mm outer diameter is fabricated from 10-mm thick plate by welding along a helix that forms an angle of 20° with a plane perpendicular to the axis of the pipe. Knowing that a 280-kN axial force P is applied to the pipe, determine the normal and shearing stresses in directions respectively normal and tangential to the weld. (Input the answer with the appropriate sign.)