Questiond Calculate the center of mass of the top spherical segment (h R/3). Assume the mass density is uniform.

Q: An open rectangular tank 18 m long, 4 m wide and 3m deep is filled with liquid. How much liquid will...

A: Given L=18mw=4md=3ma=3m/s  

Q: Determine the magnitude and coordinate direction angles of the resultant force acting at A. Where F ...

A: Find the magnitude and direction of resultant force. Given data : -  Fab = 800 N Fac = 650N

Q: If the 80 kg cyclist took 3.00 m horizontal distance to reach 5. 20 m elevation above the ground. Wh...

A:

Q: The following figure shows a journal bearing supports a radial load of 10 kN at speed of 2400 RPM. B...

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts f...

Q: A 250 lb refrigerator is being pushed. You do not know what force P should be applied. The coefficie...

A: μs=0.4W=250lbd1=4.5ftd2=1.5ftd3=2.5ftd4=3.5ft To-Find:- 1) Force (P)=............lb2) Location (x)=....

Q: A bucket is suspended from a traveling crane which is moving with the speed the crane carriage sudde...

A: Given

Q: The following data are obtained from a tensile test of a copper specimen. - The load at the yield p...

A: Note: As per policy, we can solve the first three subparts. Please resubmit the remaining parts. The...

Q: [Assume any missed Data] The input shaft of the gear train, shown below, drives gear 2 at 1xx RPM (x...

A: Since we only answer upto 3 subparts, we will answer the first 3.please resubmit the question and sp...

Q: e. Determine the maximum allowable value of P

A: Determine the maximum allowable value of  p

Q: (Problem 2) Alcohol (specific gravity = 0.80) is flowing through a horizontal pipe which is 10 inche...

A: Write the Bernoulli's equation between the smaller cross-section pipe and the larger cross-section. ...

Q: life of the ball bearing

A: Given: If the load on a ball bearing is reduced to half, the life of the ball bearing ? Therefore; B...

Q: The Link at AB rotates with an angular velocity of Wab to move piston C. da B OAB di A d1 = 0.4m d2 ...

A: For solution refer below images.

Q: Select all forces that will NOT have an effect (moment) at point O. Assume each space is a 1x1 unit ...

A: Product of force and perpendicular distance between point and application of force is known as momen...

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension, negat...

A: It is required to determine force in each member of loaded truss

Q: ahas a maximum Value &

A: solution of above problem is below:  

Q: Two designs for a beam are to be considered. Determine which one will support a moment of M= 150 kN....

A: Given:  Bending Moment, M=150 kN-m M=150×106 N-mm

Q: (4 blanks) An ice-making machine operates in a Carnot cycle. It takes heat from water at 0.0 °C and ...

A:

Q: The inlet of a centrifugal pump is 7 ft above a water surface level. The reentrant inlet (KIN = 1) i...

A: when V  is flow velocity through pipe head required by pump is equal to head loss ue to friction and...

Q: Q5. A mercury barometer located in a room at 25°C has a height of 0.750 m. The density of mercury at...

A: GIVEN DATA- h=0.750m ρ=13534 kgm3 WE HAVE TO CALCULATE PRESSURE

Q: What is the resulting gage pressure when one pound of air at a gage pressure of 15 torr and 95°C is ...

A:

Q: 2. Draw the complete shearing force and bending moment diagrams. 10 K 10 K 3 ft 8 ft 3 ft

A:

Q: A tensile load of 330,000 N is applied to a copper pipe with maximum allowable stress of 110 MPa and...

A: Answer: The thickness of the pipe is 10.55 mm. Hence, the correct answer is option (D).  

Q: Problem 204. In an 11.2 dm high cylindrical container, whose base area is 1 dm², a frictionless pist...

A:

Q: 2. The truss in Fig. Q6 supports the vertical in members HG and HB of the truss and state if the mem...

A:

Q: The number of degree of freedom

A: Given; The number of degree of freedom of a planar linkage:  22 links and 27 simple revolute joints....

Q: Two components of a two-dimensional flow in polar coordinates are given as  Vr = Vocosθ [1 – (a/r)^2...

A: For checking flow is steady incompressible or not, we applied steady flow condition and incompressib...

Q: 1200kg • A rectangular boat with additional load at the center of 7200 kg is submerged in water by 1...

A:

Q: What will be max. height that the water tank that will become full if the max. tangential stress is ...

A: Given  maximum tensile stress = 11700 psi Thickness of the tank = 0.5 in width of the tank = 15 ft =...

Q: B. A Highway Engineer tabulates the following ADT for the Highway that will be constructed. the dail...

A: AADT* k factor = hourly volume design The k factor is the hourly volume adjustment factor for the de...

Q: What will be max. height that the water tank that will become full if the max. tangential stress is ...

A: Given data Maximum Tangential Stress =  σt = 11700 psi = 11700 x 12 x 12 = 1684800 lb/ft3Given speci...

Q: Air passes along an insulated horizontal pipe of 0.05 m2 cross sectional area. In the pipe it passes...

A: Given data Area of insulated pipe = 0.05 m2Temperature at entry = T1 = 20°C = 293 KPressure at entry...

Q: A Carnot engine delivers 130 kW of power by operating between temperature reservoirs at 160°C and 16...

A: GivenPower P=130kWT1=160oC=160+273=433KT2=1660oC=1933Kt=26min =26×60 s

Q: A tube with 45 meters long, and a diameter of 1.8 meters and 2.3 meters, inlet and outlet respective...

A: The rate of change in velocity with respect to its length is -0.3014 s-1.

Q: A vessel is initially connected to a reservoir open to the atmosphere. The connecting valve is close...

A:

Q: Two axial members are used to 4.3 m support a load P applied at joint B. Member (1) has a cross-sect...

A:

Q: A 10-ft boom is acted upon by the 840-lb force shown. Determine the tension in each cable and the re...

A:

Q: The Drag Polar Equation of an General Aviation Aircraft in clean configuration can be written as: Cp...

A: Given: W = 2300 lb CD = 0.027 + Cl2/32.787  

Q: Explain the importance of a cone clutch with an application.

A: GIVEN DATA- CONE CLUTCH GIVEN WE HAVE TO EXPLAIN ITS IMPORTANCE AND APPLICATION

Q: Water flows through a constricted pipe at a uniform rate. At one point, the diameter of the pipe is ...

A:

Q: Calculate the amount of energy required in BTU to heat the air in a house 30 by 50 by 40 ft from 10 ...

A:

Q: Superheated steam at 7.585 MPa (1100 psia) and 616.3 K (650 F) enters the high-pressure turbine of a...

A: At state 1 : Saturated water and P1=7kPa h1=163.3655 kJ/kg v1=.0010075 m3/kg Wp1=h2-h1=v1∆P h2-163.3...

Q: y F1 02 F2 F3 Three forces act at the same point as shown. Determine the magnitude (N) of the result...

A: Given Data

Q: A solid mctal ball is falling in a long liquid column and has attained terminsal velocity-2 m's l'in...

A: the body approaches terminal velocity when there is no net force on the body , i.e. drag due to visc...

Q: Three masses, m, =3 kg, m2 = 5.5 kg, and m3 = 2 kg, are attached to springs, k1 = 50 N/m, k2 = 35 N/...

A:

Q: A piston-cylinder containing steam at 700 kPa and 250o C undergoes a constant pressure process until...

A:

Q: 2. The spherical steel weighs 15 kN with a diameter of 6 m. The length of distance AB is 8 m. Determ...

A: Given data:- weight of sphere = 15 kN Diameter = 6 m Find the tension at A And reaction at B

Q: receives 15,400 kg/h of Bled steam. If the condenser pressure is 0.005 MPa and the open heater press...

A:

Q: 3. For the rotational system shown below, find the transfer function, G(s) = "L(s) T(s) IN-ms/rad IN...

A: Given : To find : Transfer function

Q: A tank open to the atmosphere contains oil of sp. gr. = 0.80, gasoline sp.gr. =0.90 and seawater sp....

A:

Q: A person is pushing on a uniform block of wood as shown in the figure and parameter table. The block...

A: Given: mass of the wood=140Kg coefficient of static friction of wood(μw)=0.25 so the weight of the w...

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.