1. Determine which listed material below is the best candidate for a cylindrical rod of 200mm and having a diameter 20.0mm and subject to a tensile load of 55000N, The cylindrical rod should not experience plastic deformation or diameter reduction of 0.015mm. Justify your answer. Material Modulus of Elasticity (GPa) Yield Strength (MPa) 400 600 800 1300 Poisson's Ratio 140 202 0.33 0.34 0.30 414 D 214 0.34

1. Determine which listed material below is the best candidate for a cylindrical rod of 200mm and having a diameter 20.0mm and subject to a tensile load of 55000N, The cylindrical rod should not experience plastic deformation or diameter reduction of 0.015mm. Justify your answer. Material Modulus of Elasticity (GPa) Yield Strength (MPa) 400 600 800 1300 Poisson's Ratio 140 202 0.33 0.34 0.30 414 D 214 0.34

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 0.013 m diameter, 0.5 m long cylindrical metal bar is subjected to a compressive force of 8,500 N. This load does not exceed the yield strength of the material. Determine its diameter under this load. You will need some of the following properties of the metal to solve the problem: modulus of elasticity = 207 GPa, Poisson’s ratio = 0.30, yield strength = 180 MPa, tensile strength = 380 MPa, ductility = 23% elongation.
Experiments were conducted in a tension testing machine to evaluate the material properties of two metallic rods both having diameter equal to 10 mm. First rod having modulus of rigidity of the material equal to 400 tonnes/cm2 when subjected to an axial tensile force of 6 kN, the change in its diameter was observed to be 0.0018 cm. The value for the bulk modulus of the second metallic rod is same as that of the first one but modulus of elasticity 18% more. Based on the material properties calculate and compare the values of different moduli as well as Poisson’s ratio for both metallic rods. Justify your answer with reasons.
A cylindrical rod 500 mm long, having a diameter of 12.7 mm, is subjected to a tensile load of 30,000 N. The rod is to experience an elongation not more than 1.3 mm and FOS ≥ 1.5 setting yield strength as a criteria. Additional constraints to be met are max specific stiffness and %EL not more than 0.15. Which of the below listed materials are possible candidates? Justify your choice(s) by making a table of constraints.
10. A torsion test shows that the shear modulus of an aluminumspecimen is 4.6 x 106psi. When the same specimen is used in atensile test, the modulus of elasticity is found to be 12.2 x 106psi. Find the Poisson’s ratio for the specimen.
Draw the tensile curves of the following materials, taking into account the appropriate elongation at break, modulus of elasticity and tensile stress, on the side stress-strain graph. a)Low carbon steel (Ecelik=200Gpa),(Syield=300MPa),(Stensile=400MPa) b)High carbon steel (Esteel=200GPa),(Stensile=700MPa) c)Aluminum (Ealuminum=70GPa), (Syield=200MPa),(Stensile=300MPa) d)Cast iron (Ecast iron=120GPa),(Stensile=200MPa)
a) Compression tests are generally performed on brittle materials-why?b) How a cast iron specimen fails under compression load?c) Define secant modulus?
Figure 6.23 shows the tensile engineering stress– strain curve in the elastic region for a gray cast iron. Determine (a) the tangent modulus at 25 MPa (3625 psi) and (b) the secant modulus taken to 35 MPa (5000 psi).
A 1.64 m long rectangular AISI 1020 cold rolled steel bar (10 mm x 25 mm) is subject to a torsional load of 76.6 N·m. What is the safety factor against yielding? (Use Shigley for material properties.)
A material has the following properties, ultimate Sul = σul = 350mpa, the strain hardening exponent n=0.20. Determine the value for the strength coefficient K.
6. Discuss the different types of volume change in concrete at early and long-term ages. 8. A center-point loading flexural test was performed on a concrete beam having a size of100×100×500 mm. The beam is sitting on two supports located at 25 mm from each edge ofbeam. If the failure load was 17.5 kN, find the flexural strength.9. Considering the two tests of flexure, 3-points and 4-points, which one is more suitable forbending test and why?10. The compression strength test was performed on several samples of concrete molded in fourtypes of molds cubes of 0.100 m×0.100 m ×0.100 m and of 0.150 m×0.150 m × 0.150 m, andcylinders having a cross section of d=100 mm by H=200 mm and d=150 mm by H=300 mm,respectively. If the weight of the samples and the loads at failure are as given in the Table. Bothcubes and cylinder samples are cast from the same concrete batch under the same conditionsand subjected to the same curing method.11. Calculate the density (in kg/m3) and the compressive strength…
Steel springs must have a modulus of resilience of at least 2.0 MPa. What should be the minimum yield strength (in MPa) of a 10mm diameter spring used to support a load of 10,000 N if elongation is 1mm for every 100mm length?
information: "When performing a tensile test of a metal, these values were found for stress and strain. the yield strength (YS) is stress at 0.2% plastic strain" The task: A 5 meter long rod of this material is loaded axially with a stress of 244 MPa.i. How long is the rod under load?ii. Then the bar is relieved, how long is it now?