1. For the following friction materials used for clutches, find the values of dry and wet friction coefficient from online resources (website). Carbon graphite Leather on steel Molded asbestos Wood on steel or or cast iron on steel on steel cast iron 2. Name the different types of clutches. Give at least one practical application for each. 3. What is woven asbestos friction material? Why asbestos friction materials are prohibited in many countries?

1. For the following friction materials used for clutches, find the values of dry and wet friction coefficient from online resources (website). Carbon graphite Leather on steel Molded asbestos Wood on steel or or cast iron on steel on steel cast iron 2. Name the different types of clutches. Give at least one practical application for each. 3. What is woven asbestos friction material? Why asbestos friction materials are prohibited in many countries?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the maximum, minimum and average pressure in a plate clutch when the axial force is 3.3kN. The inside radius of the contact surface is 81mm and the outside radius is 110 mm. Assume uniform wear.
A local utility vehicle production company have considered using in one of its design a multi-disc clutch consisting of a 9 steel disc and 8-bronze discs with effective outside and inside diameter of 220mm and 160mm, respectively. If the shaft turns at 150rpm and an axial force of 600N is applied, find the horsepower capacity, considering a coefficient of friction of 0.25
A single plate friction clutch with both sides of plate being effective is used to transmit power at an engine speed of 200rpm. It has outer and inner radii 10cm and 8cm respectively. Find maximum power transmitted and the corresponding axial thrust, if the maximum intensity of pressure is not to exceed 0.08N/mm2 . Assume coefficient of friction as 0.25.
4) In a single plate clutch both sides are effective. The clutch transmits 10 Kw power. The maximum torque is 120 Nm, the maximum axial force should not be more that 100 KN/m2. The outer diameter of the clutch plate is 1.3 times of the inner diameter. Find out the axial load exerted by the spring and outer and inner diameters of the clutch plate.
An multi axial plate clutch used in injection molding machine consist of a three pairs of contact surfaces for engaging and disengaging power from the engine. The engine used for power has a maximum torque capacity of 120 N-m and is transmitted to machine without losses. The permissible intensity of pressure is 350 kPa and the coefficient of friction is 0.35 for the clutch system used in the machine. It was determined that the machine will operate on maximum capacity of torque if the ratio of inner diameter to outside diameter of the axial clutch is 0.577. Assuming uniform wear theory, calculate the inner and outer diameters of the friction lining.
A pulley 590 mm in diameter transmits 50 kW at 520 rpm. The arc of contact between the belt and pulley is 144 degrees, the coefficient of friction between the belt and pulley is 0.35 and the safe working stress of the belt is 2.2 MPa. Find the width of the belt used if its thickness is 8 mm.
The factor of safety against slipping in the friction clutch = 1.3; coefficient of friction=0.3; working speed= 600 rpm; friction surface number= 2; If required clamping force = 2917 N, clutch outer diameter = 400 mm, clutch inner diameter = 160 mm, what is the transmitted power?
An electric motor running at 1200 rpm drives a punch press shaft at 100 rpm by means of a 130 mm wide and 8 mm thick belt. When the clutch is engaged, the belt slips. To correct this condition, an idler pulley was installed to increase the angle of contact, but the same belt and pulley were used. The original contact angle on the 200 mm motor pulley is 160 degrees. The original tension ratio is 2.4 and the net tension is 12 N/mm of the belt width. If an increase in transmission capacity of 20 % will prevent slippage, determine the new angle of contact. Please show your correct and complete solution to this problem. ASAP! Thanks.
The factor of safety against slipping in the friction clutch = 1.3; coefficient of friction=0.4;working speed= 600 rpm; friction surface number= 2; required closing force= 712 N, clutch outerIf diameter = 300 mm, clutch inner diameter = 120 mm, how much power is transmitted?
a single-start, square-threaded power screw with the following parameters: PARTS A - D circle final answers for each part A - A weight of 1500 N must be lifted. What is the total required torque necessary to lift this weight? Give your answer in units of N m. Part B - if the available power to drive the screw is 1,011 Watts, determine the fastest speed at which the weight can rise. Give your answer in units of mm/s, Part C - The efficiency of the preceding power screw (expressed as a number between 0 and 1, not as a percentage) is ? Part D - Suppose a high-quality thrust bearing was used to eliminate the collar friction. The efficiency of the screw would now be?
The coefficient of friction of a disk clutch with two pairs of contact surfaces is 0.25. The maximum pressure under working conditions is 220kPa only. The clutch is used to connect two 25mm solid shafts with allowable shearing stress of 69 MPa. The inner and outer diameter of the clutch face is 60 mm and 120mm, respectively. What is the power in kW transmitted at 1000 rpm?
1. A jack having square threads of 50 mm nominal diameter and 10 mm pitch is supporting a load of 89 kN. A double thread is used and the coefficient of friction maybe as low as 0.10 or as high as 0.15.a. Will this screw always self-locking?b. What is the highest torque necessary to raise the load?