I need the answer as soon as possible A multi disc clutch transmits 55KW of power at 1800 rpm. Coefficient of friction forthe friction surface is 0.1. Axial intensity of pressure is not to exceed 160KN/m². Theinternal radius is 80 mm and is 0.7 times the external radius. Find the number ofplates needed to transmit the required torque assuming uniform wear conditions.

Answered: Image /qna-images/answer/d006e189-342f-4a71-b774-403090456621.jpg

A multi disc clutch transmits 55kW of power at 1800 rpm. Coefficient of friction for the friction surface is 0.1. Axial intensity of pressure is not to exceed 160kNIm. The internal radius is 80 mm and is 0.7 times the external radius. Find the number of plates needed to transmit the required torque assuming uniform wear conditions.

A multi disc clutch transmits 55kW of power at 1800 rpm. Coefficient of friction for the friction surface is 0.1. Axial intensity of pressure is not to exceed 160kNIm. The internal radius is 80 mm and is 0.7 times the external radius. Find the number of plates needed to transmit the required torque assuming uniform wear conditions.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A single disc clutch is used to transmit 12kW power at 1000rpm. The axial pressure is limited to 0.08 N/mm2. If the external diameter of the friction lining is 1.25 times the internal diameter, find the required dimensions of the friction lining. Assume uniform wear conditions. The coefficient of friction may be taken as 0.3.
A soft cone clutch has a cone pitch angle of 10°, mean diameter of 300 mm and a face width of 100 mm. If the coefficient of friction is 0.2 and has an average pressure of 0.07 N/mm2 for a speed of 500 rpm, find : (a) the force required to engage the clutch; and (b) the power that can be transmitted. Assume uniform wear. [Ans. 1470 N ; 10.4 kW]
A multiplate clutch has three pairs of contact surfaces. The outer and inner radii of the contact surfaces are 100 mm and 50 mm respectively. The maximum axial spring force is limited to 1 kN. If the coefficient of friction is 0.35 and assuming uniform wear, find the power transmitted by the clutch at 1500 r.p.m.
The coefficient of friction of a disk clutch with two pairs of contact surfaces is 0.25. The maximum pressure under working conditions is 220kPa only. The clutch is used to connect two 25mm solid shafts with allowable shearing stress of 69 MPa. The inner and outer diameter of the clutch face is 60 mm and 120mm, respectively. What is the power in kW transmitted at 1000 rpm?
The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.
A friction clutch is to transmit 8kW at 2600 rpm. It is to be a single plate type with both sides of the plate effective, the axial pressure being limited to 0.09 N/mm2. The coefficient of friction is 0.3. If the external diameter of the friction lining is 1.4 times the internal diameter. By assuming uniform wear conditions analyze all the given parameters to determine the required dimensions of the friction lining
A cone clutch has an angle of 12 dgrees and coefficient of friction of 0.42. Find the axial forcerequired if the capacity of the clutch is 8 KW at 500 rpm. The mean diameter of the active conicalsections is 300 mm. Use uniform wear method.
A multiplate disc clutch transmits 55 kilowatt of power at 1800 rpm. Coefficient of friction for the friction surface is 0.1. Axial intensity of pressure is not to exceed 160 KN/m2. The internal radius is 80mm and is 0.7 times external radius. Find the number of plates needed to transmit the required torque.
A conical Clutch transmits rotation from one rotating shaft to another though frictional forces on the conical face. The following data is for a conical clutchInside Diameter 25.0 mmOutside Diameter 100 mmCoefficient of Friction 0.33Axial Force 1000NIncluded angle 100 degreeRotational speed 1500rev/minuteCalculate the Torque and Power that can be transmitted without slipping using both Uniform Pressure Theory and Uniform Wear Theory
A cone clutch is to transmit 7.5 kW at 900 rpm. The cone has a face angle of 12o. The width of the face ishalf of the mean radius and the normal pressure between the contact faces is not exceeding0.09Nmm2⁄. Assuming uniform wear and the coefficient friction between contact faces as 0.2. Find themain dimensions of the clutch and the axial force required to engage the clutch.
A cone clutch is mounted on a shaft which transmits power at 200 rpm. The small diameter of the cone is 200 mm, the cone face is 50 mm and the cone face makes an angle of 12 degrees with the horizontal. Determine the axial force necessary to engage the clutch to transmit 7 kW if the coefficient of friction of the contact surfaces is 0.15. What is the maximum pressure on the contact surfaces assuming uniform wear?
...A plate clutch with single driving plate with contact surfaces on each is required to transmit 35 kW at 2400 rpm. Given that μ = 0.29, R = 1.25r, Pmax = 0.2 MPa, determine the inside radius of the frictional surface in mm. Assume the uniform wear conditions.