1. For the frame shown, determine the reactions at the supports and the horizontal and vertical components of the pin forces acting on member ABCD. Also, find the internal axial load (P), shear force (V), and bending moment (M) at point H located 2 feet to the left of point C. 12 A B 6 3 kips 4 kips

1. For the frame shown, determine the reactions at the supports and the horizontal and vertical components of the pin forces acting on member ABCD. Also, find the internal axial load (P), shear force (V), and bending moment (M) at point H located 2 feet to the left of point C. 12 A B 6 3 kips 4 kips

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter9: Application Of Influence Lines

Section: Chapter Questions

Problem 11P

See similar textbooks

Similar questions

Beams ABC and CD are supported at A, C,and D and are joined by a hinge (or moment release)just to the left of C. The support at A is a sliding support(hence reaction Ay = 0 for the loading shownbelow). Find all support reactions; then plot shear (V)and moment (M) diagrams. Label all critical V andM values and also the distance to points where eitherV and/or M are zero.
Compute the support reactions of the given beam below. Also, determine the maximum value of the positive and negative shear as well as the moment. Note: pt. a is hinge support, pt. b is roller support, pt. c is internal hinge support, pt. d is internal roller support, pt. e is roller support, and pt. f is a hinge support. Hint: Try to expose the internal reaction/s of the internal hinge support at pt. c as well as for pt. d internal roller support. For the units, the forces are in kN, then for the distances, take it as meters
The belt passing over the pulley is subjected toforces F1 and F2, each having a magnitude of 40 N. F1 acts inthe -k direction. Replace these forces by an equivalent forceand couple moment at point A. Express the result in Cartesianvector form. Set θ = 0° so that F2 acts in the -j direction.
Compute the force in member BD in kN. P1=186kN, P2=107 kN and x = 7.9 m. Write numerical value only and in 2 decimal places
(a) Determine the reactions at the supports and draw the bending moment diagram for the following structures. (b) Repeat problem (a) if there are a support movement of A to left by 10mm and a support settlement at D by 12mm. Given E=200GPa, I=107mm4 .
Determine the internal normal force, shear force, andbending moment in the beam at points C and D. Assumethe support at A is a roller and B is a pin.
5. Rod AB is fixed to a smooth collar D, which slides freely along the vertical guide. Determine the internal normal force, shear force, and bending moment at point C, which is located just to the left of the 60-lb concentrated load. Use the sign convention discussed.
The ends of the triangular plate are subjected to three couples. Given that F1= 600 N, F2 = 255 N, and α= 50°, determine the magnitude of the force F so that the resultant couple moment is 400 N.m clockwise.
The 30m long compound beam has an internal hinge at point E and is supported by pin C roller D and roller F. The pin is subjected to the loading as shown in the image. Find the internal normal force (N), shear (V) and moment (M) at points A and B.
Force F acts on the frame such that its componentacting along member AB is 650 lb, directed from Btowards A. Determine the required angle Φ (0° ≤ Φ ≤ 45°)and the component acting along member BC. Set F = 850 lband θ = 30°.
The ends of the triangular plate are subjected to three couples. Determine the magnitude of the force F so that the resultant couple moment is 500 N.m clockwise Choices are: 682.85 N 982.85 N 729.71 N 829.71 N
Rod AB is fixed to a smooth collar D, which slides freely along the vertical guide. Determine the internal normal force, shear force, and moment at point C, which is located just to the left of the 60-lb concentrated load.