1. How much voltage is generated due to residual flux in the poles? 2. How much voltage is generated at no-load with field resistance Rf1? 3. How much voltage is generated at no-load with field resistance Rf2? 4. Which line represents a field resistance higher than the critical field resistance? How much voltage does the machine generates at this field resistance.

1. How much voltage is generated due to residual flux in the poles? 2. How much voltage is generated at no-load with field resistance Rf1? 3. How much voltage is generated at no-load with field resistance Rf2? 4. Which line represents a field resistance higher than the critical field resistance? How much voltage does the machine generates at this field resistance.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A self-excited DC shunt generator is delivering20 A to a 100-V line when it is driven at 200 rad/s.The magnetization characteristic is shown inFigure. It is known that Ra = 1.0 Ω andRf = 100Ω . When the generator is disconnectedfrom the line, the drive motor speeds up to 220 rad/s.What is the terminal voltage?
No. 8 problem A shunt generator has the following open-circuit characteristic at 800 r.p.m. Field amperes : 0.5 1.0 1.5 2.0 2.5 3.0 3.5E.M.F. Volt : 54 107 152 185 210 230 245 Armature and shunt field resistances are respectively 0.1 Ω and 80 Ω. The terminal p.d. falls to 175 V when the armature current is 100 A. Find the O.C. volts and the volts lost due to (i) reduction in the field current(ii) armature resistance (iii) armature reaction.
Two generators, each having no-load voltage of 500 V, are connected in parallel to a constant resistance load consuming 400 kW. The terminal p.d. of one machine falls linearly to 470 V as the load is increased to 850 A while that of the other falls linearly to 460 V when the load is 600 A. Find the load current and voltage of each generator. If the induced e.m.f. of one machine is increased to share load equally, find the new current and voltage.
An 8 pole, lap connected armature has 500 conductors and its generated e.m.f is 120V. If theflux per pole is 20 mWb, then the speed of machine is, Choose the correct answer (a) 105 rpm (b) 420 rpm (c) 180 rpm (d) 720 rpm
A 30 kW, 300 V , 4- pole lap series generator has 160 conductors and the resistance of each conductor is 0.005 Ω if mechanical efficiency is 95% and electrical efficiency is 95.45% Find: a- The losses in armature resistance. b- The resistance of series field. c-rotational losses
1-The power output of the three phase machine is greater than the single phase machine. (TRUE/FALSE) 2-In thermocouple, when both the junctions are at the same temperature, the potential difference developed across both junction is zero. (TRUE/FALSE) 3-Due to decreased armature m.m.f., the armature reaction during load condition will increase and hence field flux will be distorted. (TRUE/FALSE) 4-While applying voltage in CRO, the grid is positive with respect to cathode. (TRUE/FALSE) 5-Losses in transformers are generally low and thus efficiency is high. (TRUE/FALSE)
The following sequential statements, when completed, describe the operation of a DC separately-excited generator. Complete each statement by inserting the most appropriate word from among those provided in the word list below. Note: A word cannot be used more than once. There are more words than required.Word list: forces, load, voltage-regulation, speed-regulation, commutator, linearly, exponentially, induces, voltage, constant, property, current, prime-mover, wave, accelerate, alternating, Faraday’s, torque, motor, Ohm’s, direct, higher, rated, Lenz’s, power, brushes, rectified, voltage-drop mechanical, speed, counter, slip, no-load, full-load, lap, rotating, oppose, power, increase, speed, lower, direction, rotating, commutator. Most generators operate at constant speed and the output terminal voltage is adjusted by varying the stator field ______________. When a load is connected across the terminals a load current will be established in accordance with Faraday’s The armature…
Problem details: A 15 kW, 280V, 1200 rpm washing machine needs to be fed by a generator in your home. You have a friend in a generator manufacturer company. He gave you different options and as you’re studying in EE department, he asked you to choose the best one from those! The generator details are as shown Type of Generator: Series Armature resistance (Ω) = 0.8 Field resistance (Ω) = - Series Resistance (Ω) = 2.2 Hysteresis loss (kW) = 1.1 Eddy current loss (kW) = 1.7 Rotational loss (kW) = 1.2 Calculate the following things for each of the generator types: a) The generated voltage b) The field circuit voltage c) The developed torque d) The efficiency Also neatly draw the circuit diagram for all of them.
Q2: A500 kW, 500 V, 10 poles d.c generator has lap wound armature Find the electrical angle shift of brushes when AT4 / pole = 208 AT. If the ATC for same generator when connected as wave wound is 2600 AT when the brushes on G.N.A.
A 220V shunt generator has an armature resistance of 0.02ohms and a shunt field resistance of 44ohms. at rate load, the driving engine develops 62.26hp. If the iron and friction losses amount to 1600W, how much is the current delivered to the load at this condition? (Our subject is ELECTRICAL MACHINE 1, and our lesson is Losses and Efficiency on the DC MACHINE) (I need a clean solution ma'am/sir. Thank you do much)
Electrical Engineering Dep. Electrical Machine Lab. NO LOAD CHARACTERISTIC OF DC MOTORS DISCUSSION 1- Comment on the curves obtained . 2- What are the types of the losses in the DC machines?
A shunt generator delivers 195 A at terminal p.m. of 250 V. The armature resistance and shunt field resistance are 0.02 ohm and 50 ohm respectively. The iron and friction losses equal 950 W. Find (a) E.M.F. generated (b) Cu losses (c) output of the prime mover (d) commercial, mechanical and electrical efficiencies.