1. In a breakwater that is 580 meters long un the shape of a slop, what is the area, perimeter and the total volume of the structure? 2. what is the area, perimeter and total volume of the main mantle and secondary mantle? 3. what is the distances of a,b, c and H from the cross section drawing

Q: What is the coefficient of volume change (using change in void ratio method) for pressure range 100…

A:

Q: How do metamorphic rocks that form deep inside the Earth under ductile conditions get exposed to the…

A: The conditions required to form a metamorphic rock are very specific. The existing rock must be…

Q: Continent |(density 2800 kg/m³) mg Mantle rock (density - 3300 kg/m) Problem 5: The figure above on…

A: Solution;

Q: After filling the tank shown in Figure 3a, the plane of the major principle stress in element A will…

A: A cylindrical tank of dia 10m, and surcharge stress of 100 KP a.Unit wt of soil = 16 KN/m3Depth of…

Q: The upstream pressure on a rock sample is 0.113MPa and the downstream pressure is 0.1MPa. Under this…

A: Darcy's law : Darcy's law is a mathematical formula that defines how fluid flows through a porous…

Q: Explain the lithification process in the formation of the sedimentary rock

A:

Q: Point loads of magnitude 10O, 200, and 400 kN act at A, B, and C, respectively. the increase in…

A:

Q: q= 21,358 kN/m² H1= 1,871 m B Yn= 18,557 kN/m³ H2=1 m Yn= 19,557 kN/m³ H3= 5,871 m Yn= 20,557 kN/m³…

A: Pore water pressure :-   It is the pressure generated around the soil particles due to the presence…

Q: write a full report about rock mass properties. About Methodology . With details

A: Rock mass is a matrix which is made up of rock material and rock discontinuities. Rock mass…

Q: Consider two series of triaxial compression test data, one for Rock A and one for Rock B. Which of…

A: As we know the elastic behavior of any material is dependent on th modulus of elasticity of…

Q: The pore water pressure (kPa) at D due to capillary rise is y = 16.0 kN/m? Ysat = 16.5 kN/m3 0.5 m D…

A:

Q: 1. Some geophysical (dynamic) tests were performed in the field on a rock layer, and the velocity of…

A:

Q: 9.30 A laminar boundary layer velocity profile is app by the two straight-line segments indicated in…

A:

Q: Find the vertical stress at depth 10m below point A on the loaded area shown in figure if Aq=100…

A: GIVEN  Radius , R=10m  Depth , Z=10 m   △q=100KN/m2

Q: What is the intensity of active earth pressure at a depth of 10.0 m in dry sand with an angle of…

A: Angle of shearing resistance = 30o and unit weight of 18 kN/m3.

Q: 1. Some geophysical (dynamic) tests were performed in the field on a rock layer, and the velocity of…

A:

Q: change (using chan method) for pressure range 100 kN/m to 200 kN/m ? (Consider o' = 100 kN/m , e =…

A: Given data : ∆σ = 100 kN/m2 e0 = 1.121 ∆e = -0.157 where, ∆σ = change in effective stress. e0 =…

Q: Present proposals for subsurface structures in response to the hydrostatic pressure of a given…

A: There are a number of options to consider when designing subsurface structures that can withstand…

Q: The elastic settlement below the center of the tank at z = 0 and 3m. The elastic settlement at (i) z…

A:

Q: What is the effect on the eddy formation if surface roughness is more?

A: We have to mention the effect on the eddy formation if surface roughness is more.

Q: A thin walled cylindrical pressure vessel having a radius of 0.5 m and wall thickness of 25 mm is…

A:

Q: What is the coefficient of volume change (using change in void ratio method) for pressure range 100…

A: Given data, Change in effective stress, ∆σ = 100 kN/m2 Initial void ratio, e0 = 1.121 Change in void…

Q: Calculate the stress distribution with depth below the center of the dam, and the stres distribution…

A:

Q: )The Mohr circles representing the states of stress at two points, A and B, and in the same rock…

A: "Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: For the dam spillway shown in Figure 1, draw a flownet at a scale of 1 inch = 10 meters. Using this…

A: The values and diagram given in the question are as follows Permeability(K)=1.8*10-4 cm/sec…

Q: A confined aquifer of 15 m constant thickness is sandwiched between two aquicludes as shown in the…

A: Given- Thickness of the aquifer B=15 m, Heads h1=55.2 m & h2=34.1 m, Hydraulic conductivity k=80…

Q: Sketch and briefly explain the formation of different main beddings in sedimentary rocks.

A:

Q: A spherical ball of volume 106mm³ is subjected to a hydrostatic pressure of 90 kN/m². If the bulk…

A: Given- Volume of spherical ball V=106 mm3 Hydrostatic pressure P=90 kN/m2 Bulk modulus K=180 MPa It…

Q: A single rectangular opening 10 ft in height is driven in rock having strengths of fc=18000 lb/in2…

A: A rigid composite system's moment of inertia is equal to the sum of the moments of inertia of its…

Q: How far apart must two 20 m diameter tanks be placed such that their combined stress overlap is not…

A: Given; Depth =10m 20 m diameter tanks   10% of the surface contact stress

Q: What is the coefficient of volume change (using change in void ratio method) for pressure range 100…

A:

Q: Qi! For the soil profile shown in the figure (1): 1- Calculate total vertical stress at the middle…

A:

Q: Along the depth for the floor profile given below; Plot graphically the total vertical stress, pore…

A: At point A-Total stress σ=q=30 kPaPore pressure μ=0Effective stress σ¯=σ-μ=30 kPaAt point B-Total…

Q: 9.) If a rock has a permeability of 1 millidarcy, how much water will flow through it per unit of…

A: step 1-

Q: Calculate the added vertical stress at points A and B as deep as Z = 8 m, under the rectangular load

A:

Length and Length related Variables

Length can de defined as the measurement or extent of physical quantities or objects from one terminal to another terminal. Stone age humans used finger length, step length, and so on to measure the size or displacement of an object. Nowadays, depending on how precise the measurement requires to be and the object’s size is measured, we use measuring devices for measurements like rulers and steel tape. Most people have used a ruler or tape measure to measure a particular distance or the size of an object. For more precise measurements of tiny objects, the development of measurement tools such as the Vernier caliper, which permits us to measure dimensions within 1/1000 of an inch. In the last few decades, electronic distance measuring instruments (EDMI) have been implemented that permit us to measure distances from a few feet to many miles with reasonable accuracy.