1. The aluminum shaft shown has a constant diameter, with 1000 N-m applied at gear A, 1200 N-m removed at gear B, 800 N-m applied at gear C, and 600 N-m removed at gear D. Determine the minimum diameter of the shaft if the allowable shearing stress of the shaft is 25 MPa and the angle of rotation of gear A relative to gear D is limited to 40.

1. The aluminum shaft shown has a constant diameter, with 1000 N-m applied at gear A, 1200 N-m removed at gear B, 800 N-m applied at gear C, and 600 N-m removed at gear D. Determine the minimum diameter of the shaft if the allowable shearing stress of the shaft is 25 MPa and the angle of rotation of gear A relative to gear D is limited to 40.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The drive shaft AB of an automobile is made of a steel having allowable shear stress of tallow = 8 ksi. If the outer diameter of the shaft is 2.5 in. and the engine delivers 200 hp to the shaft when it is turning at 1140 rev>min, determine the minimum required thickness of the shaft’s wall.
The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. 1.) Determine the maximum shear stress in the shaft in ksi. (Answer in 2 decimal places) 2.) Determine the angle of twist in degrees of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible. (Answer in 3 decimal places)
The 6-hp reducer motor can turn at 1200 rev>min. If the allowable shear stress for the shaft is tallow = 6 ksi, determine the smallest diameter of the shaft to the nearest 1 16 in. that can be used.
A hollow shaft for a rotary compressor is to be designed to transmit a maximum torque of 4750 N-m.The shear stress in the shaft is limited to 50 MPa. Determine the inside and outside diameters of theshaft, if the ratio of the inside to the outside diameter is 0.4. [Ans. 35 mm ; 90 mm]
A flange coupling is to be designed, using 6 bolts at a distance of 149mm from thecenter of the shaft, allowable shearing stress on the bolt is 103 MPa. If the shaft is totransmit 5485 hp at a speed of 1200 rpm, (a) determine the bolt diameter required inmm. (b) If the shaft is made of the same material as the bolt, determine the requireddiameter of the shaft in mm.
A hollow bronze shaft of 75 mm outer diameter and 50 mminner diameter is slipped over a solid steel shaft 50 mm indiameter and of the same length as the hollow shaft. The twoshafts are then fastened rigidly at their ends. Find the maximumshearing stress developed in the bronze by end torque of 3 kN.mFor bronze G = 35 GPa and for steel G = 83 GPa.
A solid steel shaft AB, shown in Fig. is to be used to transmit 5 hp fromthe motor M to which it is attached. If the shaft rotates at v = 175 rpm andthe steel has allowable shear stress of tallow = 14.5 ksi, determine therequired diameter of the shaft to the nearest 18 in.
Question twoa) Shafts and tubes having circular cross sections cannot be used to transmit powerdeveloped by a machine. True or False? b) Explain the concept of torsion. c) If the applied torque on shaft CD is T = 75 N.m, determine the absolute maximumshear stress in each shaft. The bearings B, C, and D allow free rotation of the shafts,and the motor holds the shafts fixed from rotating
The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C.a)Determine the maximum shear stress in the shaft in ksi.b)Determine the angle of twist in degrees of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible.
A 40-mm diameter hole is drilled 3-m deep into the steel shaft. When the first torque is removed at point B with 6000-N-m and the second torque is applied at point C with 2000-N-m, determine the following:a) The Maximum Shear Stress in the shaft.b) The angle of rotation of the free end of the shaft.
The 2-in.-diameter drive shaft AB on the helicopter is subjected to an axial tension of 10 000 lb and a torque of 300 lb # ft. Determine the principal stresses and the maximum in-plane shear stress that act at a point on thethe surface of the shaft.
The steel shaft DF consists of three concentric tubes and is supported by smooth bearings at D and E. It is coupled to a motor at F, which delivers 15 kW of power to the shaft while it is running at 55 rev/ sec. The gears A, B, and C remove 4 kW, 5 kW, and 6 kW, respectively. The shaft is free to turn in its support bearings D and F. Determine the shearing stress developed in segments BC and CE