A hollow bronze shaft of 75 mm outer diameter and 50 mm inner diameter is slipped over a solid steel shaft 50 mm in diameter and of the same length as the hollow shaft. The two shafts are then fastened rigidly at their ends. Find the maximum shearing stress developed in the bronze by end torque of 3 kN.m For bronze G = 35 GPa and for steel G = 83 GPa.

A hollow bronze shaft of 75 mm outer diameter and 50 mm inner diameter is slipped over a solid steel shaft 50 mm in diameter and of the same length as the hollow shaft. The two shafts are then fastened rigidly at their ends. Find the maximum shearing stress developed in the bronze by end torque of 3 kN.m For bronze G = 35 GPa and for steel G = 83 GPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.3.12P: A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable...

See similar textbooks

Similar questions

A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A 40-mm-diameter solid shaft is subjected to an axial force of P = 2790 N, a vertical force of V = 1650 N, and a concentrated torque of T = 50 N-m, acting in the directions shown. Assume L = 130 mm. Determine the horizontal shear stress τxy at point K.
A hollow steel shaft, 6 ft long, has an outer diameter of 3 in. and an inner dieter of 1.5 in. The shaft is transmitting 200 hp at 120 rev/min. Determine (a) themaximum shear stress in the shaft; and (b) the angle of twist in degrees. Use G =12 x 106 psi for steel. complete solution
A circular composite shaft is made of a 50-mm-diameter brass (G = 40 GPA) and a 80-mm-outside diameter aluminum (G = 25 GPA) jacket. This shaft is 1.5-m-long and both ends are rigidly mounted so they cannot twist. What is the shear stress at the outer surface of this shaft when a 100 N-m torque is applied at the center?
A steel shaft (G = 80 GPa) with an external drive of 30mm must transmit a torque of 2700 N-m. The allowable shear stress in torsion is 120 MPa and the allowable rotation for the member is 0.1 rad / m. Design to the nearest millimeter the internal radius required for the steel drive
A hollow steel shaft of length 1.75 m transmits 2000 kW of power at a speed of150 rev/min. The inside diameter is to be 0.75 times the outside diameter. Themaximum allowable torsional shear stress for the steel is 130 MN/m2and themodulus of rigidity (G) for the steel is 83 GN/m2. Given that a factor of safety of2 is required for the shaft, determine:i) the torque acting on the shaft;ii) the required external and internal diameters for the shaft; iii) the torsional shear stress set-up in the shaft material at the inside surfaceof the hollow shaft, and sketch the stress distribution through the shaftwall;iv) the angle of twist (in degrees) due to the torque.
A keyed gears delivers a torque of 912.4 N-m thru its shaft of 63.5 mm outside diameter. If the key has thickness of 15.875 mm and width of 11.1125 mm, find the length of the key. Assume permissible stress value of 61.2 MPa for shear and tension at 99.8 MPa
A hollow steel shaft, 6 ft long, has an outer diameter of 3 in. and an inner diameter of 1.5 in. The shaft is transmitting 200 hp at 120 rev/min. Determine (a) themaximum shear stress in the shaft; and (b) the angle of twist in degrees. Use G =12 x 106 psi for steel
Determine the minimum diameter that can be used for a solid circular steel shaft which is limited to an allowable shear stress of 70 MPa and a maximum angle of twist of 1.5o (degrees) per meter length. Applied maximum torque is 25 KN-m and the overall shaft length is 1.25 meters. Shear modulus = G= 80 GPa Note: When using torsion stress formulas, you must convert the angle of twist from degrees to radians.