1. The block shown reaches a velocity of 12m/sec. in 30m. starting from rest. Compute the coefficient of kinetic friction between the block and the ground. V₁ =0 Wo W = 70 kg P= 24 kg F 30 m V₂ = 12 m/s W N=W F=UN

1. The block shown reaches a velocity of 12m/sec. in 30m. starting from rest. Compute the coefficient of kinetic friction between the block and the ground. V₁ =0 Wo W = 70 kg P= 24 kg F 30 m V₂ = 12 m/s W N=W F=UN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Given below is the result of a sieve analysis done on a soil sample. Sieve No. Diameter Percent…

Q: A tube 3.6 mm thick has an elliptical shape with a major axis length = 151 mm and minor axis length…

Q: Coarse aggregates from two stockpiles having coarse aggregate angularity (crushed faces) of 40% and…

A: Using equation X=P1x1+P2x2X=percent of crushed aggregate of blendP1,P2= proportion of…

Q: Reinforced concrete structure is a composite material consist of concrete and steel reinforcing bar,…

Q: wo beams, one having square cross section and another circular cross-section, are ubjected to the…

A: Solution:- Considering the case when both beams have the same cross-sectional area, one with a…

Q: Solve for the member forces only. Do not include the support reactions in solving for the member…

A: Given data

Q: 2m WIDE PI 3m Find the magnitude of the hydrostatic force. a. 146.7 kN b. 199.3 kN Im 4m c. 294.3 KN…

Q: 40gal/min of water is pumped and the energy loss in the discharge line is 13.5 feet and at the…

Q: A bucket is hanging from a horizontally moving crane. Calculate the maximum allowable speed (m/s) of…

Q: Calculate the bending stresses in the beam using the transformed area method. Use a concrete…

A: Given values: b = 14 in D = 24 in Area of steel bars, 6#9 bars = 1 in2 * 6 = 6 in2 n =8 M = 110 ft-k…

Q: Find the critical buckling load (SI unit) for a long column with a length of 3 m and a fixed -…

Q: B Figure P-109 30- W 50⁰

Q: Problem 5.82 (Figure 1) Figure 1 2f Express your answers using three significant figures separated…

A: Given that :

Q: Use the virtual work method to determine the vertical deflection and the horizontal deflection at…

Q: Structural steel is used in hot-rolled structural shapes, plates, and bars. Structural steel is used…

A: Rolling structural steel segments are steel segments created in rolling mills to be used as…

Q: A built-up shape is shown in Figure 1, a) determine the elastic section modulus; b) determine the…

Q: Three reservoirs are connected in a common junction. Following are the pertinent information:…

A: Reservior-1ZA=90 mL1=1800 mD1=0.4 mf1=0.02Reservior-2ZB=50 mL2=2000 mD2=0.5…

Q: Determine the slope and displacement at the end C of the beam. El is constant. Use the Double…

Q: If the diameter of a shaft subjected to torque alone is doubled, then the horse power P can be…

A: Given data- Diameter of shaft is doubledHorse level=PTo Find-Incresed horse power.

Q: The water is flowing through a P, 39.24 N/cm D, 20 cm Problem 6.4 pipe having diameters 20 cm and 10…

Q: STRENGTH OF MATERIALS UPVOTE WILL BE GIVEN. Please write the complete solutions legibly. Answer in 3…

Q: Determine the forces in members BE and CE of the loaded truss. A 3m 45° 5 kN 3m E BC=CD 3 kN 3m

Q: Explane of Heat Treatment.

A: A method called "heat treatment" is used to change a material's physical characteristics for the…

Q: Please round to the nearest One Tenth (i.e., 0.1). No comma! Moist unit weight of soil, gamma = 108…

Q: Problem-7 A pre-tensioned rectangular concrete beam 150 mm wide and 300 mm depth is prestressed with…

A: Given- width=150 mmdepth=300 mmarea=50 mm2stress=1200 N/mm2modluar ratio m=6

Q: Situation 4: A uniform 80-m pipe that weighs 960 kN is supported entirely by a cable AB of…

Q: From Figure 1 shown below, Determine the following (Absolute value): A Than 5.00 meter W- 37.09-…

Q: A hollow concrete masonry unit has actual gross dimensions of 190 mm * 190 mm* 390 mm (width *…

A: Gross area =190×390=74,100mm2Net area =Vh=6106190=31,578.947mm2

Q: A pre-tensioned rectangular concrete beam 150 mm wide and 300 mm depth is prestressed with three…

Q: A sample of dry soil is coated with a thin layer of paraffin and has a mass of 460 g. It displaced…

A: Given data: A sample of soil with, Mass of soil + paraffin = 460 g Volume of soil + Volume of…

Q: Determine the forces in members BE and CE of the loaded truss. A 3m 45° 5 kN B 3 kN D

A: Given :

Q: 1. The cantilever beam in Figure 1 is fixed at A, and is loaded with a distributed load from A to B…

Q: Determine the z-coordinate of the mass center of the homogeneous paraboloid of revolution shown.

A: Given: r= 8in. and h= 20in.

Q: Please round to the nearest Tenth (i.e., 0.1). Moist unit weight of soil, gamma = 103 pcf The factor…

Q: The discharge in a channel with bottom width 3 m is 12 m³ s. If Manning's n is 0.013 m-1/3 nd the…

A: The given data is: Channel width, b=3 m Discharge, Q=12 m3/s n=0.013 m-1/3 s Slope, S=1 in 200=0.005…

Q: 13.A simply supported steel beam of length 2.5 m. and height 15 cm. is bent by couples M at the…

Q: Using the Cantilever Method, determine the Moment Reaction at point B of the given Frame. Answer…

Q: circular footing is 2.73 meters in diameter. The bottom of the footing is 2.75 m. below the ground…

A: Diameter of footing = D= 2.73m Depth of Foundation of Footing =Df= 2.75m Moist unit weight of soil =…

Q: The central angles of a compound curve are 30° and 40° respectively. In addition, the degrees of the…

A: Curves: Curves are the regular bends which are provided in continuation of roads, railways etc.…

Q: A 46-kN axial load P is applied to a short wooden post that is supported by a concrete footing…

A: Given P = 46 KN = 46*10³ N Required Maximum size of footing for average bearing stress of 141 KPa…

Q: The discharge in a channel with bottom width 3 m is 12 m³ s. If Manning's n is 0.013 m-3 s and the…

Q: Type of Heat Treatment.

A: Heat treatment is the procedure of heating metal without allowing it to reach its molten, or…

Q: Draw the shear, moment, elastic curve, and axial force diagram of this frame. Provide the summary of…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: The spherical grit particles, having a radius of 0.01mm and specific gravity of 3.0, need to be…

A: Given- radius=0.01 mmG=3g=9.81 m/s2density ρ=1000 kg/m3

Q: Q1/ For the footing shown in Figure (1). estimate the pile group capacity. 0.6m dia bored pile Clay…

A: Ultimate load carrying capacity of pile: It is the maximum load which can be applied on pile without…

Q: A wide variety of shapes can be produced by cold-forming and manufacturers have developed a wide…

A: A forging process called cold forming often referred to as the cold roll formation process, is being…

Q: Analyze the structure using slope deflection method solve for the reaction at support A and support…

A: Slope Deflection Method A and B are the fixed end supports and C has a vertical reaction at L/2 from…

Q: 1. From the given cross-section notes, compute the volume of earthworks between the two stations.…

A: Solution: 1. Given data: Station = 12+440 m h1 = 4 m h2 = 8 m h = 6 m Slope = 2:1 L = 20 m B = 20 m…

Q: A sample of dry soil is coated with a thin layer of paraffin and has a mass of 460 g. It displaced…

Q: Draw the Influence Line for the for the truss member KJ and JE. L 1680 B K i C 8 ft 8 ft 8 ft J To…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

1. The block shown reaches a velocity of 12m/sec. in 30m. starting from rest.
Compute the coefficient of kinetic friction between the block and the
ground.
V₁ = 0
Wa
I
W = 70 kg
P= 24 kg
30 m
V₂ = 12 m/s
W
N=W
FUN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

If the body starts from rest at A and slides 200 ft down the 30° incline, how far will it then move along the other incline? What will be the velocity when it returns to B? Coeff fr= 0.20. please use energy-work method.
8. A tank has a length of 2.5 m and width of 2.0 m and contains water at a depth of 1.15 m. If the tank is subjected to an linear acceleration of 4.25 m/s-2 parallel to the length of the tank, determine the height of the sides such that no water will be spilled.
Compute the horizontal and vertical components of the hydrostatic force (magnitude and direction) on the half cylinder AB for a unit distance normal to paper. γ1 = 8 kN/m3, γ2 = 12 kN/m3 h1 = 4 m, h2 = 2 m R = 2 m
If the block reaches point C at a speed of 6m/s, what is the horizontal distance X betweenB and C? (Note: v0=4 m/s, calculate using theWork and Energy Method. The frictioncoefficient is 0.25 on all surfaces)
1. A tank, under a head h, has a circular orifice located at its vertical side. The diameter of the orifice is Imm. The center of the orifice is 8m above a level ground and the jet strike the ground 20m from the orifice, measured horizontally. Neglect air friction and assume a value of Cv = 0.90.
A thin flat plate 55 by 110 cm is immersed in a 5.6-m/s stream of SAE 10 oil at 20°C. Compute the total friction drag if the stream is parallel to: a. the long side. b. the short side.
Determine the drag on a paddle with an area of 0.06 sq.m. moving horizontally at 0.8 m/s. CD = 0.45.
For figure, determine the volume of solid generated by the revolution of this area around a vertical axis passing through the left edge of the figure. Also determine the centroid of the generated solid. A=218 B=41 C=11
A closed cylindrical tank 1.845m high and 0.945m in diameter contains water of height 1.35m. When the angular velocity is constant at 20rad/sec , If it is rotated at 15rad/sec and the air has a pressure of 200kPa what is the minimum pressure at the bottom of the tank in KPa? CHOICES a.) 220.48 b.) 22.48 c.) 202.48 d.) 248.22
The tank shown in figure is of a depth d = 48.8 cm and width w =24.4 cm accelerated by ax = 3.43m/sec2 to the right, find the allowable water height (h) to avoid spill of water during acceleration
A tanker contained with water is pushed horizontally at constant acceleration of 5.0 m/s?. If the tank is 10 m long and the depth of the water is 3 m when at rest, Calculate; a) The angle of water surface to the horizontal. b) The maximum pressure intensity on the bottom How far below the water surface should the top side of a vertical square 1 m on each side should be immersed so that the center of pressure will be 70 mm below the center of gravity? complete solution needed
Oil flows through a small standard 25m diameter orificce under a head of 5.4 m at the rate of 0.0031 m3/s. The jet strikes a wall 1.52 m away and 0.119 m vertically below the centerline of the contracted section of the jet. Compute the coefficient of velocity.