1. The cylinders are piled in a rectangular ditch as shown. Neglecting friction, determine the reaction between cylinder A and the vertical wall. Cylinder Weight (Ib) Radius (in) A 15 4 В 40 20 lb 20 Neglect friction = smooth surface 40 lb 15 lb 18"-

1. The cylinders are piled in a rectangular ditch as shown. Neglecting friction, determine the reaction between cylinder A and the vertical wall. Cylinder Weight (Ib) Radius (in) A 15 4 В 40 20 lb 20 Neglect friction = smooth surface 40 lb 15 lb 18"-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: If H = 4 m, D = 10 m, h = 0.4 m, k = %3D 0.0001 cm/s and y = 0.2 m, the porewater pressure at C is…

A: Given data in question Coefficient of permeability Upstream head Downstream head To find out Pore…

Q: Based on the provided differential-type manometer, calculate the difference in the pressure between…

A: To find :- the pressure difference between points A & B.

Q: Water flows into the atmosphere from a nozzle and strikes a vertical plate as shown in the figure…

A: Diameter of pipe (D1) = 0.3m Area of pipe (A1) = Πd2/4 = 0.0706 m2 Diameter of the nozzle (D2) =…

Q: The water in the pipe given in the Figure Flows uniformly in sections I and 2. 1. Pipe diameter in…

A: Given information in question Diameter 1 = 20 cm V1 = 20 m/s Diameter 2 = 4 cm Density of fluid =…

Q: A tank with vertical sides is 1.30 m square (horizontal section), 3 m high and is filled with water…

Q: The diverging tube shown in the figure discharges water when h =5 ft. Area A is 1.5 times Ao.…

Q: Two hydraulic cylinders in a hydraulic system are shown in Figure 3.2. The inner diameters of the…

A: In piston A, given Velocity of flow = V1 = 1.25 m/s diameter = d1 = 75 mm = 0.075 m…

Q: P.3.5 Three pipes A, B. and C at the same level connected by a multiple differential manometer shows…

A: Let Density of water be ρw = 1000 kg/m3 Density of mercury = ρHg = 13500 kg/m3 Differential…

Q: T ту S e12 m 7. Prove that the most efficient hydraulic trapezoidal cross section envelopes a…

A: Most efficient hydraulic trapezoidal cross section has the following properties 1. Side slope m = 13…

Q: Oil flows from a tank through a 150mm diameter pipe and then discharges into air as shown. If the…

A: Given:- head loss from point 1 to point 2= 600mm diameter=150mm SG of oil=0.84 flow=17L/s To find:-…

Q: 36 " chinge Linseed Oil А (SG = 0.938) Castor Oil 32 feet (SG = 0.96) 7 feet 11ater В

Q: Based on the provided differential-type manometer, calculate the difference in the pressure between…

Q: A square tank 1.20m on each side, 3m deep is filled to a depth of 2.70m with water. A wooden cube…

Q: Determine the load that can be lifted by the hydraulic system shown. Use g = 9.81 m⁄s2 .

A: According to Pascal's law, In a fluid at rest in a closed container, a pressure change in one part…

Q: Analyze the rectangular block shown in Figure, subjected to a uniform pressure P = 30 + (2506/1000)…

A: Given, P=30+25061000=32.506 psi The given pressure is same in all directions. Thus σx=σy=σz=-32.506…

Q: Question- A circular shaped hatch closes the out flow of a tank. a) Determine the mass m, such that…

Q: 61 pipes were packed in a cylinder. Calculate the shell hydraulic diameter? 0.75 D6.80 D0.60 H0.75 -

A: Step 1

Q: Oil flows through a smooth pipe of diameter D = 4 cm between points (1) and (2) that are 4 m apart…

Q: For the below figure, find pressure head, total head, datum head at point A. Assume velocity head is…

A: Given: The seepage length is 5m. Consider the figure.

Q: The cylinder shown in the figure extends 9 ft into the paper. If the cylinder has the radius of 4…

A: Given Data: Length of cylinder is L=9 ft=2.743 m. Radius of cylinder is R=4 ft=1.219 m. Specific…

Q: A vertical rectangular gate 1.8m wide and 4.2m high is submerged in oil (SG-0.88) with its bottom…

Q: Oil (sg=0.87) flows from A to E as shown. The head loss is assumed to be as follows: A to B = 0.45…

A: To Determine Pressure at point C in Psi.

Q: For the tank shown in the figure, compute the pressure at points A & B. AIR 2m ail 2m water s0.82 3m…

Q: 5. A circular pipe of radius 7 cm is used for water flow transmission. This pipe is moulded into…

A: Given data- Radius of circular pipe (R) = 7cm Pipe is moulded in sqaure ,where keeping the length…

Q: A 3m Oil: 2m S.g. = 0.9 %3D (F), B 2m Water (F,

Q: 1. Determine the difference in pressure between points A and B. Use unit weights for water and oil…

Q: 5. If the pressure in a tank of oil (sp gr 0.85) is 3yx kN/m2, what is the equivalent head (a) in…

Q: Refer to the given figure. Given: a = 42cm, b= 15cm, and c= 34cm Water a C 40 cm Gate Unknown liquid…

Q: 7. For the Pitot Tube below, determine the height that the fluid rises, L, in the column if water is…

A: Velocity of flow through pitot tube is given and it has been asked to determine height of fluid…

Q: Q1: Calculate the pressure at point A in a water flow. If the pressure at B is 87 kPa. Assume all…

A: As per guidelines plz post Q 2 separately

Q: The figure shows a cylinder of 4 m dlameter in equilibrium. Calculate the vertical component of…

Q: An inverted differential manometer is connected to two pipes A and B which convey water. The fluid…

A: I have followed usual notations of inverted manometer

Q: 8) Estimate the height to which water will rise in a capillary tube of diameter 3mm. Use o =0.0728…

Q: A container 10 m wide and 10 m long contains water 2 m high and is accelerating to the right at a…

Q: Refer to the given figure. Given: a = 36cm, b = 24cm, and c = 29cm Water ← b с Į 40 cm Gate Unknown…

A: use simple method just find force by individual fluid and make net force zero on the gate

Q: In figure 2.5, if the pressure of gas in bulb A is 50 cm Hg vacuum and Patm = 76 cm Hg, the height…

Q: 1.0m 0.20m O(pivot) W= 35 KN 6o cm diam 5 Cm iam h= 7m oil (2) (s = 0.85)

A: diameter of the plungerd=7.5 cmarea of the plungera=π47.52a=44.17 cm2diameter of the ramD=40 cmarea…

Q: Air flows through a pipe at a rate of Q (L/s). The pipe consists of two sections of diameters D1…

Q: n the figure,which fluid will a pressure of 700kPa first be achieved? P. = 90kPa ethyl alcohol,p =…

Q: The flow rate of water flowing out of an 80mm diameter nozzle shown in Figure 1 is 60 litre/s. The…

Q: In the figure below, determine the force F (newton) to balance the weight of the cylinder. Cylinder…

Q: 5. The container is partially filled with oil. Water and air as shown. Determine the pressures at A,…

Q: ischarge of the system shown in the figure given below is 15 + It/sn. The flow is opened to the…

A: It means the size of the force. It is the sum of all forces acting on a body. If two forces act in…

Q: and n, in feet of fluid A, when: A. Fluid A is gasoline (sp gr 0.715), the gage liquid is mercury,…

A: Writing pressure equation:Pm+γA4.2+z-γgz=PnHead diff=Pm-PnγA=4.2+z-γgγAz

Q: Given: 4 tank full of water and oil (Set 0.S0), as shown. Find: The pressure at the oil water…

Q: 0.20 m h 0.20 air m y 0.60 m 0.60 (0.60) = 0.40 I 0.30 m 0.30 m 0.30 0.30

Q: Q1: Calculate the pressure in A, B, C, D in Pascal. Air A Air 0.6m P1 0.3m Oil 0.6m S=0.9 water 1m…

Q: Q.4) Determine the range of cylinder mass m for which the system is in equilibrium. The coefficient…

Q: 1. The cylinders are piled in a rectangular ditch as shown. Neglecting friction, determine the…

A: Given that ,WA=15 lb ; RA=4 inWB=40 lb ; RB=6 inWC=20 lb ; RC=5 in…

Q: For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two…

A: Specific gravity of linseed oil, SG1=0.938Specific gravity of castor oil, SG2=0.96The value of z =…

Concept explainers

Site Plan Requirements

A site plan (also known as a plot plan) is a diagram or process to show the proposed improvements on an existing property. A site plan is important, as it provides information regarding the landscape features of a given plot of land. Zoning is done or can be understood with the help of a site plan.

Question

Please answer the problem on the attached photo.

1. The cylinders are piled in a rectangular ditch
as shown. Neglecting friction, determine the
reaction between cylinder A and the vertical
wall.
Cylinder
Weight (Ib)
Radius (in)
A
15
4
В
40
20 lb
20
Neglect friction = smooth surface
40 lb
15 lb
18"-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Water flows through a new cast iron pipe at a velocity of 1.8 m/s. The pipe is 480 m long and has a diameter of150mm. Determine the head loss due to friction using Manning’s formula with n = 0.012.
3. Two concrete pipes are connected in seriesThe flow rate of water through the pipes is 0.14 m/s with a total friction loss of 14,10 m for both pipes. Each pipe has a length of 300 m. If one pipe has a diameter of 300 mm, what is the diameter of the other one? Neglect minor losses Use dot f = 0.021
Show the necessary figures (if applicable) 2.3) Points A and B are separated by 915 m of new 152.4 mm diameter cast iron pipe. 50 lps of water flow from point A to point B. Point B is 18.5 m above point A. What must be the pressure at point A if the pressure at point B is 345 kPag and the head loss between A and B is 54 m? 2.4) A pipe discharges 142 lps of water into a reservoir at a point 1.85 m below the water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm. If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
Points A and B are 5km apart along a new 60cm diameter cast iron pipe carrying water. A is 9m higher than B. If the pressure at B is 140KPa greater than at A. f=0.019. Determine the head loss in meters. a. 5.27 b. 7.52 c. 2.75 d. 7.25
If DA = 20cm, DB = 11cm and L = 6m, and if oil is flowing at a rate of 0.05 m3/ s, determine the difference in pressure between sections A and B. Neglect head losses.
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. A. 12.9517 B. 39.5136 C. 99.9358 D. 30.4889 What gage pressure p1 in kPa, is needed to provide the given flow rate? A. 1121 kPa B. 1725 kPa C. 1692 kPa D. 1328 kPa
Q2. A 200 mm x 100 mm venturimeter is provided in a vertical pipeline carrying oil of S = 0.9. The flow is in the upward direction. The throat is above the inlet by 0.25 and the differential manometer shows a gauge deflection of 0.25 m of Hg. Determine,(a) Discharge of oil (b) The pressure difference in N/m”2 between entrance and throat by using basic Bernoulli's equation. Take Cd = 0.98*
. A pump draws water from a reservoir and conveys it to another reservoir 30 m above. The sucLon pipe is 100 mm in diameter and 10 m long while the delivery pipe is 100 mm in diameter and 150 m long. if the velocity in the pipe is 3 m/s, the fricLon factor of the pipe 0.008, and the pump and motor efficiencies 85 % and 92 %, respecLvely. See Figure Q6.1. Calculate:(a) Gauge pressure at the pump's inlet (at C) (10)(b) Gauge Pressure at the pump's outlet (at D) (10)(c) input power to motor (5)
Given: a= 1.57m b= 1.16m c=0.68m Carbon tetrachloride,sg=1.60 Determine the pressure difference (kPa) between points A and B. Neglect sign
Oil (SG = 0.87) discharges from a pipe (D1 = 13 in.) through a sharp-crested, round orifice (D2 = 4 in.) as shown. The coefficients of contraction and velocity are 0.632 and 0.904, respectively. Find the actual discharge in the orifice in ft3/s. Use x = 7.8 in., y = 2.3 ft. Round off to four decimal places.
Derive a formula for capillary rise (h) between two concentric glass tubes of radiuses RI and R2. determine its value for water if ((ro)Gw. = 0.072 N/m, RI=30mm, & R2=36mm) (Take smooth and very clean glass tubes).
Water is flowing at the rate of 4.7 cu.m./min. through a 150mm-dia. pipe which slopes downwardsuch that a 75mm-dia. exit orifice is 0.60m lower than the upper end. Assume no friction loss. The sharp edged orificehas a coefficient of contraction of 0.65. What is the pressure at the point A in KPa?