ELEVATION 20MELEVATION30mAIR Po?150mmøSG-0.84Oil flows from a tank through a 150mm diameter pipe and then discharges into air as shown. If the head loss from point 1 to point 2is 600mm, determine the pressure needed at point 1 to cause 17L/s to flow (SG of oil = 0.84)(А) 82.19 КРав) 87.74 КРас) 98.23 КРаD) 93.30 КРаE) 76.49 KPa

Given:- head loss from point 1 to point 2= 600mm diameter=150mm SG of oil=0.84 flow=17L/s To find:-…

Answered: Oil flows from a tank through a 150mm…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Refer to Fig. P5.4. Water at 10°C flows up AB (5 m long, 40 mm diameter),then along BC (3 m long, 30 mm diameter). The measured pressure at A is 275kPa. (a) Find the pressure at C if the flow rate is 2.0 L/s. Neglect pipe frictionand energy losses. 6) Repeat for the same flow rate in the opposite direction.Table A.1 for water at 10°C: y = 9.804 kN/m².Vertical
A pump draws water from a 20 cm diam suction pipe and discharges through a15 cm diam pipe in which the velocity is 3.60 m/s. The pressure is – 34. 465 kPaat A in the suction pipe. The 15 cm diam pipe discharges horizontally into air atC. To what height h above B can the water be raised if B is 1.8 m. above A and20 hp is delivered to the pump? Assume that the pump operates at 80 %efficiency and that the frictional loss in the pipe between A and C is 3 m. Determine the inclination angle at point C for the water stream to reach a range of 50 m. Also, calculate the maximum height that the water can go from the selected datum plane.
oil (SG = 0.88) dischargesfrom a pipe (D = 13 in.) through a sharp-crested, round orifice (diameter = 5 in.), as shown. the coefficients of contraction and velocity are 0.619 and 0.967, respectively. find the actual velocity (in ft/s) in the jet. Point (1) is a point collinear with the orifice at point (2). Point (3) is the free surface of the manometer containing mercury. use h = 2.84 ft., and y = 7.42 in.
Water enters the bottom of the cone in Fig. P3.24 at auniformly increasing average velocity V = Kt . If d is verysmall, derive an analytic formula for the water surface rise h ( t )for the condition h = 0 at t = 0. Assume incompressible fl ow.
For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids - castor oil (0.96) and water. Considerinh a unit-width of the gate, apoly the PRESSURE PRISM CONCEPT (Illustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z = 20ft.
A reservoir contains water has a vertical circular orifice 25.2mm diameter and is first plugged up to measure any displacing force, the tank is suspended in a particular way. The horizontal force is required to keep the tank in place on the removal of the plug. The opposite applied force to the orifice is 16.8N. The volume per time was found as 141lt/minute. It is assumed that the level of the water is maintained at a constant height of 2.785m above the orifice. Calculate Cc, Cv, and Cd for the orifice.
Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. a.12.9517 b.39.5136 c.30.4889 d.99.9358 What gage pressure p1 in kPa, is needed to provide the given flow rate? a.1692 kPa b.1121 kPa c.1328 kPa d.1725 kPa
Two compartments A and B are connected by a standard orifice of 30 cm^2 with C = 0.60 in a prismatic vessel. A has a horizontal cross-section of 30m^2 and B has a horizontal cross-section of 40m^2. At one point in time, the water in A is 6 meters above the orifice's center, whereas the water in B is 3 meters. When will the water's surface be 1 meter apart? Answer : 49 secs
Fluid mechanics, i need solutions in 10 minutes please. Q/Q2 The 4 -m- diameter circular gate of Fig. E2.6a is located in the inclined wall of a large reser voir containing water (y = 9.80 kN / m³). The gate is mounted on a shaft along its horizon tal diameter. For a water depth of 10 m above the shaft determine: (a) the magnitude and lo cation of the resultant force exerted on the gate by the water, and (b) the moment that would have to be applied to the shaft to open the gate.
A pump draws water from a 20 cm diam suction pipe and discharges through a 15 cm diam pipe in which the velocity is 3.60 m/s. The pressure is – 34. 465 kPa at A in the suction pipe. The 15 cm diam pipe discharges horizontally into air at C inclined at 30 degrees. Find the maximum height and range that the water can reach if B is 1.8 m. above A and 20 hp is delivered to the pump? Assume that the pump operates at 80 % efficiency and that the frictional loss in the pipe between A and C is 3 m.
A 75 mm horizontal pipe of circular cross section conveying water under a pressure of 0.75bars has its diameter reduced from 75 mm to 2 mm by means of a short transition 30 mm in length. The pipe empties into the atmosphere. The discharge is 0.14m3.s-1, what is the percentage change in mean velocities? The pipe is anchored to a pillar with the anchoring having a factor of safety of 1.5. What force must the anchor withstand to achieve the above?
A tank has one of its side inclined inward at an angle of 30° with horizontal. The free surface of the contained water is at Elev 15.25 m. The orifice located on the inclined side issues a jet, having it's vena contracta at Elev 10.70 m. If the highest point in the trajectory of the jet is at Elev 14.00 m, find the actual velocity of the jet air friction. Neglect air friction. Include fbd.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Oil flows from a tank through a 150mm diameter pipe and then discharges into air as shown. If the head loss from point 1 to point 2 is 600mm, determine the pressure needed at point 1 to cause 17L/s to flow (SG of oil = 0.84)