1. The following Flat Belt Drive Shown below was found in a certain machine, Bench Grinder Machine. The Following was investigated. Grinder Shaft Speed = 3,000 Rpm, Clockwise Pulley 1 Diameter 2 inches %3D Pulley 2 Diameter = 4 inches Pulley 4 Diameter = 3 inches %3D Center to Center Distance, Pulley 4 and 3 = 2 feet Center to Center Distance, Pulley 2 and 1 = 1.5 feet Train Value = 3 Find: 1. The Speed of the Electric Motor Rotating in RPM 2. The Diameter of the Pulley 3 3. The Length of the Belt 1 4. The length of belt 2 Pulley 4 Electric Motor Shaft Belt 2, Crossed Belt Pulley 2 Pulley 3 Belt 1, Crossed Belt Pulley 1 Grinder Shaft

1. The following Flat Belt Drive Shown below was found in a certain machine, Bench Grinder Machine. The Following was investigated. Grinder Shaft Speed = 3,000 Rpm, Clockwise Pulley 1 Diameter 2 inches %3D Pulley 2 Diameter = 4 inches Pulley 4 Diameter = 3 inches %3D Center to Center Distance, Pulley 4 and 3 = 2 feet Center to Center Distance, Pulley 2 and 1 = 1.5 feet Train Value = 3 Find: 1. The Speed of the Electric Motor Rotating in RPM 2. The Diameter of the Pulley 3 3. The Length of the Belt 1 4. The length of belt 2 Pulley 4 Electric Motor Shaft Belt 2, Crossed Belt Pulley 2 Pulley 3 Belt 1, Crossed Belt Pulley 1 Grinder Shaft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Simple Machines Give the detailed sketch how we determined the displacement of the output (SO) that was used in calculating the Mechanical Advantage of the Four Pulley System. Write the equation. Label your sketch properly.
2- Figure (2) shows an epicyclic gear train suitable for lifting machine with the following particular: Gear A is the mounted on the motor shaft and the load spindle is attached to the arm 7. planet wheels C and Ci are compound. The number of teeth on wheels A and Ci are 20 The internal wheel B is fixed. A speed reduction of about 12 is required. Find the suitable number of teeth ror C and B and the exact value of speed ratio which these give. Z as
The figure below shows a two-stage helical gear set. Pinion 2, which is in the converter position, transfers a certain rotation moment from the shaft to gear 3 in the first stage by rotating in the direction of the clock in the front view (or in the Z direction) shown in the figure. on shaft B, the pinion gear No. 4 is positioned with gear No. 3, which receives and/or transmits the drive from different gears. The number 4 Pinion in the second stage drives the number 5 gear, converting the input moment in the system to the output moment and providing movement transfer. Answer the figure in the table as follows by determining the direction of rotation of Gears 3, 4 and 5 and the Helix direction of each gear when looking at the left side view of the figure from the left (i.e. from the-z direction).Also, briefly explain how the concept of a module in Gears is determined by showing the basic dimensions on a tooth form and what the main law of gears refers to by drawing a figure.
The figure below shows a two-stage helical gear set. Pinion 2, which is in the converter position, transfers a certain rotation moment from the shaft to gear 3 in the first stage by rotating in the direction of the clock in the front view (or in the Z direction) shown in the figure. on shaft B, the pinion gear No. 4 is positioned with gear No. 3, which receives and/or transmits the drive from different gears. The number 4 Pinion in the second stage drives the number 5 gear, converting the input moment in the system to the output moment and providing movement transfer. Answer the figure in the table as follows by determining the direction of rotation of Gears 3, 4 and 5 and the Helix direction of each gear when looking at the left side view of the figure from the left (i.e. from the-z direction).
= Given the crank-slider linkage shown in Figure 1 with the linkage lengths as follows: L₂= 500 mm, L32 250 mm, and L₁= 550 mm. The distance between the supports is L₁ = 500 mm. When the angles of the links are 8₂ 36.87° and 83 53.13° the rotational angle rates of the links are wz 8 rad/s and w3 = -11.8859 rad/s. If the link R, is rotating in counterclockwise (CCW) direction with a rotational acceleration of az 5 rad/s², determine the rotational acceleration of links R₂ and the acceleration of the slider R2 03 R₁ R3 isin) R4
TRUE OR FALSE The figure below shows a gear train used in a toy car. The input shaft connects directly to the wheels of the car. When a child rolls the car over the ground the wheels act through the gearbox to spin a flywheel that stores energy. To store as much energy as possible, we would like the flywheel to spin just as fast as possible--therefore, we use the gearbox in a so-called "speed multiplier" configuration with the wheels as the input and the flywheel as the output. The tooth counts on the gears are as follows: N1 = 38 teeth N2 = 14 teeth N3 = 28 teeth N4 = 16 teeth Based on this description, the wheels should be attached to shaft B. TRUE OR FALSE ?
Shaft A Shaft B Pinion wheel Rotor 2 Shaft C Rotor 1 Gear wheel Figure Q2 Figure Q2 shows two rotors (Rotor 1 and Rotor 2), a pinion wheel and a gear wheel rigidly fixed to shafts A, B and C. The gear wheel rotates at half the speed of the pinion wheel. Polar moments of inertia of the rotors about relevant rotating axes and thestiff nesses of the shafts are given below. Rotor/Wheel Polar moments of inertia Shaft Torsional Stiffness (Nm/rad) (kgm²) Rotor 1 I A K Rotor 2 I B K C 2K Pinion wheel Negligible moment of inertia Gear wheel 61 Working from fundamentals, obtain the frequency equation for torsional oscillations of the system.
7. A typical drive train for a 'geared' bicycle meant to be used on paved road (see a representative image) has 48 teeth on front sprocket (Crank side), the diameter of front sprocket being 10.5 inches. The rear wheel has a cassette with a cluster of 6 sprockets, with number of teeth on Sprocket #1 (lowest gear) to Sprocket # 6 (highest gear) being 30, 26, 23, 20, 16 and 12, respectively. (Ignore wind resistance and friction between machine elements) (a) If the rider is pedaling at a constant 105 rpm with an effective force of 28 lb acting on periphery of front Sprocket (at 5.25 inch radius length, the force location indicated by red arrow), and is engaged in Sprocket #5, what would be the torque acting on Sprocket # 5, and the RPM at which the rear wheel is spinning? (b) For the condition as described in (a), If the diameter of wheels is 26 inches, what is the speed of the bicycle? &
Find the output speed and cycle rate, since the input speed in the gear mechanism in the figure is 900 rpm, r2=20cm, r3=8cm, r4=12cm, r5=26cm, r6=32cm, r7=6cm `input 2 out 4 5
Find the angle of contact on the small pulley for a crossed belt drive with center distance of 73", if pulley diameters are 7" and 14", respectively. Also find the difference in length if anopen belt is used instead.
Match the items in columnsI and II. Column I P. Addendum Q. Instantaneous center of velocity R. Section modulus S. Prime circle Column II 1. Cam 2. Beam 3. Linkage 4. Gear (a) P-4, Q-2, R-3, S-1 (b) P-4, Q-3, R-2, S-1 (c) P-3, Q-2, R-1, S-4 (d) P-3, Q-4, R-1, S-2
What will be the centre distance of two meshing gears il module is 4 and no ofteeths are 25 and 75?