1. The input signal in Figure 1(a) is applied to the comparator in Figure 1(b).Draw theoutput showing its proper relationship to the input signal. Assume the maximum outputlevels of the comparator are (+/-)12 V. Values of R₁ and R₂ are as follows.(a) R₁ = 8 K Ohm, R₂ = 12 K Ohm(b) R₁ = 12 K Ohm, R₂ = 8 K OhmnFigure 1(a)5 V-Vin 02. Find Output Voltage Vour for the circuit in figure - 2, below.R₁VINI = +1 VOM100 K OhmR₂VIN2 = +2 VOM200 K OhmR3VIN3+3 VC www300 K OhmR4VIN4+4 VO www400 K OhmR₂www50 K Ohm+10 VoltFigure - 2Figure 1(b)VOUTVout 3. Determine the bandwidth of each of the amplifiers in Figure 3. Both op-amps have anopen-loop gain of 200 dB and a unity-gain bandwidth of 1.2 MHz.VincR₁147 ΚΩR₁3 ΚΩFigure - 3R₂ww1.0 knR₁www1.0 ΚΩ4. Find the values of the input and output impedances in Figure - 4. Also, determinethe closed-loop voltage gain. The op-amp has the following parameters: ZIN = 2MQ2;and ZouT= 200 22. AOL = 50,000.www50 ΚΩFigure - 5www47 ΚΩFigure - 45. (a) Determine the input and output impedances of the amplifier in Figure - 5. Theop-amp datasheet gives ZIN = 2 M2, Zour = 100 92, and AOL = 100,000.(b) Find the closed-loop voltage gain.R₁out96ΚΩ4kfV outout

The input signal and the comparator circuit is shown below, The maximum output levels of the…

1. The input signal in Figure 1(a) is applied to the comparator in Figure 1(b).Draw the output showing its proper relationship to the input signal. Assume the maximum output levels of the comparator are (+/-)12 V. Values of R₁ and R₂ are as follows. (a) R₁ = 8 K Ohm, R₂ = 12 K Ohm (b) R₁ = 12 K Ohm, R₂ = 8 K Ohm SV- +10 Volt R₁ W

1. The input signal in Figure 1(a) is applied to the comparator in Figure 1(b).Draw the output showing its proper relationship to the input signal. Assume the maximum output levels of the comparator are (+/-)12 V. Values of R₁ and R₂ are as follows. (a) R₁ = 8 K Ohm, R₂ = 12 K Ohm (b) R₁ = 12 K Ohm, R₂ = 8 K Ohm SV- +10 Volt R₁ W

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

proof the equation 10.8 which represents the gain of inversting amplifer ... the proof is already exist in page 621 but there are some expressions were missed before the equation 10.7, you should start this proof from the begining and adding that missed expressions.
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: INDUSTRIAL ELECTRONICSTOPIC: FEEDBACK OSCILLATORS NOTE: Please solve in this way. 1. Please have a good handwriting, some of the answers are not readable. Thank you!2. GIVEN. (Include symbols and units)3. ILLUSTRATION (Required).4. Step-by-step SOLUTION with Formulas and Symbols. No Shortcut, no skipping, and detailed as possible5. FINAL ANSWERS must be rounded up to two decimal places with corresponding unit. PROBLEM:An amplifier has an input of 0.2W. it has an internal gain of -500 with a 10% distortion. If negative feedback is added with β = 0.05, determine the following:A. Percent reduction in distortionB. Reduction in output power due to feedback expressed in %
Figure Q. 3(b) shows an op amp circuit for linear amplifier application. (i) Determine the value of current I3.(ii) Find the value of R if the output current, Io is given as 2 mA.(iii) Explain what will happen to output voltages, V01 and V02 if the supplyvoltages, +VCC and -VCC are connected to +10V and -10V.
The circuit shown can be used as a simple 3-bit digital-to-analog converter (DAC). The individual bits of the binary input word (b1 b2 b3) are used to control the position of the switches, with the resistor connected to 0 V if bi = 0 and connected to VREF if bi = 1. (a) What is the output voltage for the DAC as shown with input data of (011) if VREF = 5.0 V? (b) Suppose the input data change to (100). What will be the new output voltage?(c)Makeatablegivingtheoutputvoltagesfor all eight possible input data combinations.
For circuit shown ini the pic. below, assuming VBE = 0.7 V.Determine: (a) IBQ(b) VB(c) ICQ(d) VE(e) VC(f) VCEQ
Discrete Signals and Discrete Time systemsx[n1] = (values) 9 any random integer values from -10 to 5x[n2] = (values) 9 any random integer values from -5 to 5 a. Plot the graph setting the middle integer value at n = 0 showing the all samples.b. Plot the graph x[-n] showing all the samples.c. Plot the graph x[n-3] showing all the samples.d. Plot the graph x[n+2] showing all the samples.e. Plot the graph x[2n] showing all the samples.f. Plot the graph x[n/3] showing all the samples.g. Evaluate the convolution of x[n1] and x[n2].
Digital system must often be interfaced with analog equipment where digital signal is one that has only two discrete voltage level, meanwhile an analog signal is one that varies continuously from a minimum to a maximum voltage or current. Figure 3 illustrates a typical situation in which the digital processing unit or system has analog inputs and outputs. The input on the left is a continuous voltage ranging from 0 to 5 V. i) State the name of X and Y.ii) State the difference between X and Y respectively.
please need correct answer and fast please Q2) The certain operational amplifier has the following data sheet specifications: IOS= 0.80 µA and IBIAS= 2 µA. The value of Current I1 at the inverting terminal will be____ µA and the value of current I2 at non- inverting terminal will be -------
8.15 MECT361 Mechatronics Components and Instrumentation 8.15. Using the Internet, look up the specifications for the National Semiconductor ( www.national.com ) ADC0800 8-bit A/D converter. Determine the maximum sam- pling rate and the method for performing the conversion. Also define each of the inputs and outputs. PLEASE GIVE ME THE REFRENCE I Will get zero if you didn't put the refrence
The circuit shown in Figure1, given that R C = 3 KΩ, R L=1KΩ, V CC = 15 V, voltage gain Av=10v and IB = 10mA. The circuit has an input signal vin of =2v. Determine the value of IC.
Plz I need the answer of this question in digital system design
Q1. for the circuit shown, if the output peak voltage = 6 V. find VB? Vin Your answer Q2. find ICQ?